(Difference between revisions)
(Created page with "{{CRLtemplate|File:SL_vader_esb_gloves.jpeg|Gloves| *The gloves are black leather (or leather-like material) and mid-forearm length. *The upper surface is quilted in lines spaced...")
Line 3: Line 3:
*The upper surface is quilted in lines spaced approximately one inch apart which run parallel to the arm and start just behind the knuckles.
*The upper surface is quilted in lines spaced approximately one inch apart which run parallel to the arm and start just behind the knuckles.
*The palm side has no quilted lines.
*The palm side has no quilted lines.
-
*[http://www.501st.com/databank/File:SL_vader_esb_gloves2.jpg Additional View 1], [http://www.501st.com/databank/File:SL_vader_esb_gloves3.jpg Additional View 2].|
+
*[http://www.501st.com/databank/File:SL_vader_esb_gloves2.jpg Additional View 1], [http://www.501st.com/databank/File:SL_vader_esb_gloves3.jpg Additional View 2].
 +
*Click '''here''' to view glove comparison and details.|
*The gloves should be made of leather (more specifically, it should match the leather of the body suit).
*The gloves should be made of leather (more specifically, it should match the leather of the body suit).
-
*The gloves should flare out at the end opening on the outside (little finger side), but not on the inside (thumb side).
+
*The gloves should '''flare out''' at the end opening on the outside (little finger side), but not on the inside (thumb side).
-
*There should be six rectangular sections created by the quilted lines on the upper surface; they are not of uniform width (the outer sections are smaller than the middle sections).|
+
*There should be six rectangular sections created by the quilted lines on the upper surface; they are not of uniform width (the outer sections are smaller than the middle sections '''View'''). |
-
*The quilted lines should be very finely stitched, and the upper surface should be padded minimally.
+
*The quilted lines should be very finely stitched, and the upper surface should be '''padded minimally'''.
-
*The quilted lines in the flared section are stitched as a "V" turning the sixth (outermost) section into a "Y".
+
*The '''quilted lines in the flared section''' are stitched as a "V" turning the sixth (outermost) section into a "Y".
-
*The stitching on the gloves, with the exception of the quilted lines, should be external.
+
*The '''stitching''' on the gloves, with the exception of the quilted lines, should be external.
-
*The top and bottom of the glove in the flared section should not be directly sewn together; an intermediate triangular section should adjoin them starting at the wrist bone. It should be approximately two inches in width at the end opening of the glove.
+
*The top and bottom of the glove in the flared section should not be directly sewn together; a '''gusset''' should adjoin them starting at the wrist bone. It should be approximately two inches in width at the end opening of the glove.
-
*The finger portion (not including the thumb) of the glove should be constructed in a typical glove fashion and contain three fourchettes-one between each set of fingers.}}
+
*The finger portion (not including the thumb) of the glove should be constructed in a typical glove fashion and contain three '''fourchettes'''-one between each set of fingers.}}

Revision as of 20:40, 27 March 2013

SL vader esb gloves.jpeg Gloves
For 501st approval:
  • The gloves are black leather (or leather-like material) and mid-forearm length.
  • The upper surface is quilted in lines spaced approximately one inch apart which run parallel to the arm and start just behind the knuckles.
  • The palm side has no quilted lines.
  • Additional View 1, Additional View 2.
  • Click here to view glove comparison and details.
For level two certification (if applicable):
  • The gloves should be made of leather (more specifically, it should match the leather of the body suit).
  • The gloves should flare out at the end opening on the outside (little finger side), but not on the inside (thumb side).
  • There should be six rectangular sections created by the quilted lines on the upper surface; they are not of uniform width (the outer sections are smaller than the middle sections View).
For level three certification (if applicable):
  • The quilted lines should be very finely stitched, and the upper surface should be padded minimally.
  • The quilted lines in the flared section are stitched as a "V" turning the sixth (outermost) section into a "Y".
  • The stitching on the gloves, with the exception of the quilted lines, should be external.
  • The top and bottom of the glove in the flared section should not be directly sewn together; a gusset should adjoin them starting at the wrist bone. It should be approximately two inches in width at the end opening of the glove.
  • The finger portion (not including the thumb) of the glove should be constructed in a typical glove fashion and contain three fourchettes-one between each set of fingers.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.