Databank - User contributions [en]

Costuming:TI 181st dress uniform

2013-05-21T01:50:56Z

Muppet:

{{CRLheader|181st Fighter Wing, Dress Uniform|File:181st_dress.jpg|TI-5435 Tom Hobson|Briana Petersen|}}

{{CRLdetinfo| 1102 |181st Fighter Wing, Dress Uniform|TI|Star Wars Expanded Universe. The 181st Imperial Fighter Group is an elite unit that served in the Imperial navy, handpicked by Baron Soontir Fel and feared throughout the galaxy as the best TIE pilots in the Empire. Their elite status is denoted by distinctive red stripes sewn onto their uniforms and painted onto the solar wing arrays of their TIE/In Interceptor series starfighters. | }}

{{CRLjrslevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:181st_tunic.jpg|Tunic,Olive|
*Fabric should be a medium weight suiting material exactly matching the pants and hat. Gabardine style weave is most accurate.
*Tunic is double-breasted with a left over right closure on the tapered yoke.
*Yoke comes up across the shoulder to the top shoulder seam.
*The standing collar has square corners and is about 1.25" (31.8mm) tall and closes snugly and includes a modesty panel behind closure. Collar edges are closed with 2 eye hooks.
*There are code cylinder pockets on both outside panels of the jacket from about half way between the top and bottom on the arm hole.
*Sleeves are long, and without cuffs or buttons,containing 2 seams, one along the bottom and one along the back.
*Red blood stripes 1" (25.4mm) to 1.5" (38.1mm) wide extend from the base of the collar to the wrist. A second pair of red stripes 1" (25.4mm) to 1.5" (38.1mm) wide appears on either side of the collar closure and are offset from the shoulder stripes.
*Collar stripes must be the same width as the sleeve stripes.
*Tunic should be constructed with no top-stitching (stitches visible on the exterior surface of fabric)|
*There is a dart of about 2" (50.8mm) in the top cener of the yoke.
*Additionally there is a seam running the entire circumference of the tunic, dividing it along a line hidden by the uniform belt.
*The back of the tunic has princess seams that run vertically and turn outward to intersect the arm-hole seam at the vertical center.| | }}

{{CRLtemplate|File:ID_pants.jpg|Jodphur Trousers, Olive|
*Fabric should be a medium weight suiting material exactly matching the tunic. Gabardine style weave is most accurate.
*Flared riding breeches are canon, with semi-stiff flares to the hip/thigh area for olive officer types. Breeches must be worn with boots (see below).
*Pockets are acceptable, though they should not be visible with the tunic on.
*There are no noticeable cuffs on the pants.||}}

{{CRLgreyimperialhat}}

{{CRLtemplate|File:ID_rankbar.jpg|Rank Bar|
* See the [[Costuming:Imperialrankbar|Imperial Rank Bar page]] for more information.
*Worn on the left side of the tunic over the heart.
*Rank consists of colored plastic tiles mounted on metal bar.
*Each bar is 1" (25.4 mm) height, length is determined by chosen rank
*Rank tile dimensions are 1/2" (12.7 mm)width x 3/4" (19 mm) height and about 1/8" (3.2 mm).
*Tiles should be mounted with 1/4" (6.4 mm) spaces between them.
*Rank tiles are translucent. Color quantity and combinations are determined by rank, and should be appropriate to uniform type (examples: no 181st officer had orange rank tiles, no 181st officer had a single-row rank bar, no 181st officer wore a black uniforms etc) |
*Double-row ranks should be constructed from separate pieces of one row each, rather than two rows of caps on a single metal backing piece.
* Double row rank bars are not allowed for staff (black) officers.
|}}

{{CRLtemplate|File:code_cylinders.jpg|Code Cylinders|
*Between 1 to 4 per costume may be worn.
*Code cylinders are dosimeter style: silver tube with short clip, top should be coloured blue.|
* Only real or replica dosimeters may be used, not chalk holders.
||}}

{{CRLofficerbelt}}

{{CRLgeneric-black-boots}}

{{CRLfooter|JRS_CRL|T}}

Costuming:TI 181st dress uniform

2013-05-18T07:15:51Z

Muppet: Protected "Costuming:TI 181st dress uniform" ([edit=sysop] (indefinite) [move=sysop] (indefinite))

{{CRLheader|181st Fighter Wing, Dress Uniform|File:181st_dress.jpg|Tom Hodson|Briana Petersen|}}

{{CRLdetinfo| 1102 |181st Fighter Wing, Dress Uniform|TI|Star Wars Expanded Universe. The 181st Imperial Fighter Group is an elite unit that served in the Imperial navy, handpicked by Baron Soontir Fel and feared throughout the galaxy as the best TIE pilots in the Empire. Their elite status is denoted by distinctive red stripes sewn onto their uniforms and painted onto the solar wing arrays of their TIE/In Interceptor series starfighters. | }}

{{CRLjrslevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:181st_tunic.jpg|Tunic,Olive|
*Fabric should be a medium weight suiting material exactly matching the pants and hat. Gabardine style weave is most accurate.
*Tunic is double-breasted with a left over right closure on the tapered yoke.
*Yoke comes up across the shoulder to the top shoulder seam.
*The standing collar has square corners and is about 1.25" (31.8mm) tall and closes snugly and includes a modesty panel behind closure. Collar edges are closed with 2 eye hooks.
*There are code cylinder pockets on both outside panels of the jacket from about half way between the top and bottom on the arm hole.
*Sleeves are long, and without cuffs or buttons,containing 2 seams, one along the bottom and one along the back.
*Red blood stripes 1" (25.4mm) to 1.5" (38.1mm) wide extend from the base of the collar to the wrist. A second pair of red stripes 1" (25.4mm) to 1.5" (38.1mm) wide appears on either side of the collar closure and are offset from the shoulder stripes.
*Collar stripes must be the same width as the sleeve stripes.
*Tunic should be constructed with no top-stitching (stitches visible on the exterior surface of fabric)|
*There is a dart of about 2" (50.8mm) in the top cener of the yoke.
*Additionally there is a seam running the entire circumference of the tunic, dividing it along a line hidden by the uniform belt.
*The back of the tunic has princess seams that run vertically and turn outward to intersect the arm-hole seam at the vertical center.| | }}

{{CRLtemplate|File:ID_pants.jpg|Jodphur Trousers, Olive|
*Fabric should be a medium weight suiting material exactly matching the tunic. Gabardine style weave is most accurate.
*Flared riding breeches are canon, with semi-stiff flares to the hip/thigh area for olive officer types. Breeches must be worn with boots (see below).
*Pockets are acceptable, though they should not be visible with the tunic on.
*There are no noticeable cuffs on the pants.||}}

{{CRLgreyimperialhat}}

{{CRLtemplate|File:ID_rankbar.jpg|Rank Bar|
* See the [[Costuming:Imperialrankbar|Imperial Rank Bar page]] for more information.
*Worn on the left side of the tunic over the heart.
*Rank consists of colored plastic tiles mounted on metal bar.
*Each bar is 1" (25.4 mm) height, length is determined by chosen rank
*Rank tile dimensions are 1/2" (12.7 mm)width x 3/4" (19 mm) height and about 1/8" (3.2 mm).
*Tiles should be mounted with 1/4" (6.4 mm) spaces between them.
*Rank tiles are translucent. Color quantity and combinations are determined by rank, and should be appropriate to uniform type (examples: no 181st officer had orange rank tiles, no 181st officer had a single-row rank bar, no 181st officer wore a black uniforms etc) |
*Double-row ranks should be constructed from separate pieces of one row each, rather than two rows of caps on a single metal backing piece.
* Double row rank bars are not allowed for staff (black) officers.
|}}

{{CRLtemplate|File:code_cylinders.jpg|Code Cylinders|
*Between 1 to 4 per costume may be worn.
*Code cylinders are dosimeter style: silver tube with short clip, top should be coloured blue.|
* Only real or replica dosimeters may be used, not chalk holders.
||}}

{{CRLofficerbelt}}

{{CRLgeneric-black-boots}}

{{CRLfooter|JRS_CRL|T}}

Costuming:TI - 181st

2013-05-18T07:15:18Z

2013-05-18T05:53:40Z

Muppet:

{{CRLheader|181st Imperial Fighter Group |File:181_full.jpg|Tyler P. Huffman|Allison Lipka|}}

{{CRLdetinfo| 1102 |TIE Pilot, 181st Imperial Fighter Group|TI|Star Wars Expanded Universe. The 181st Imperial Fighter Group is an elite unit that served in the Imperial navy, handpicked by Baron Soontir Fel and feared throughout the galaxy as the best TIE pilots in the Empire. Their elite status is denoted by distinctive red stripes sewn onto their uniforms and painted onto the solar wing arrays of their TIE/In Interceptor series starfighters. | }}

{{CRLjrslevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate-nolevels|File:TI_rotj_helmet.jpg|Helmet|
*See the [[Costuming:TI_TIE_Pilot_Helmet-detail|TIE Helmet Detail page]] for more views and information about canon paint schemes.
*Helmet may have flat or bubbled lenses in Dark Gray or Dark Green.
*The helmet must also have imperial disks (greeblies) on the ear wells.
*Two 2.75" diameter Imperial Emblems in either white or silver should be on the crest of the helmet as seen in the diagrams below.
*The frown between the teeth may optionally be drilled out. If the teeth are cut out, the openings must be backed by material so that the face is not seen.
*Colours of markings may range from chrome to silver, brushed aluminum to light gray to dark gray (gun metal), but must be consistent - pick a colour and stick with it.| | }}

{{CRLtemplate-nolevels|File:181st_hose.jpg|Hoses|
*Black Ribbed Hoses with a 1.25" diameter and 18" to 21" in length from the helmet hose port to connect to the chestbox upper hose ports.
*A third hose exits the bottom of the Type A box and the Type B box, and is wrapped with a black communications cable. See descriptions of both chestboxes for hose sizes required.| | }}

{{CRLgeneric-balaclava}}

{{CRLtemplate|File:181st_flightsuit.jpg|Black Imperial Flight Suit|

*See the [[181st Flightsuit guide]] page
* One piece black coverall/jumpsuit/flight suit with a front invisible zipper.
* Approximately 1.5" (38.1mm) tall mandarin collar with a chevron shaped, left-over-right velcro closure.
* A silver or white "imperial cog" emblem on a black background must be present on both shoulders. The cog should be 3" or 3.5" in diameter, and 1" from the shoulder seam affixed over the blood stripe.
*Red blood stipers 1" (25.4mm) to 1.5" (38.1mm) wide extend from the base of the collar to the wrist closure, and begins at the armpit seam and extends to the hem of the pant leg. See attached graphic.
* On the left forearm there is a com-pad pocket approximately 5" (127mm) wide by 5.75" (146.05mm) tall with no flap and a 2.25" (57.15mm) window in it.
* On the left bicep, below the cog emblem, there is a code cylinder pocket with no flap, and vertical stitching dividing it into pen sleeves.
* The bottom front corner of the pocket is cut off at a bevel on the side pointing in view direction with the broader upside forming the border of the pen sleeves.
* The right sleeve has a cargo pocket on the bicep, approximately located below the cog emblem.
* 2 large chest pockets and 2 large front pockets below the belt without any zipper or flaps.
* 2 leg pockets with flaps similar in proportion as the one on the right arm sleeve. Size may differ. (Usually the width of the front pockets equals the width of the leg pockets)
* Rank bars of any kind are not permitted.| |
* In the films, the Imperial patches on the shoulders were printed vinyl.
* The suit should have a pointed collar in the back. }}

{{CRLtemplate|File:181st_arm_braces.jpg|Arm Bracers|
*Bracers closely resemble soccer shinguards and shall be gloss or satin black in colour.
*Communications pad is not required when the bracers are worn.
*the bracers must fit down inside the gauntlet of the glove.| | }}

{{CRLtemplate|File:181st_flak_vest.jpg|Grey Flak Vest|
*The grey, ribbed flak vest should consist of nylon or nylon like fabric.
* There are a total of 9 correctly spaced ribs on the front with a gap between the 2 upper and 9 lower ribs. 8 "flat" ribs are sewn into the vest between the upper and lower ribs, and are left flat.
* There are 13 evenly space ribs in the back.
* Tubing should be permitted to create the illusion that the ribs are filled.
* Leather or leather like tabs with correct buckle hardware connects the front to back near the wearer's waist. A 1" (25mm) adjustment strap with adjustment tab buckle detail is found at the back of the vest. Two 2" (48mm) shoulder straps with horizontal rib stitching detail connect the front and back of the vest.| | }}

{{CRLtemplate|File:181st_harness.jpg|Web harness and optional web belt|
*The web harness and belt is the classic US Military A.L.I.C.E load bearing system. Grey or black is accepted. A.L.I.C.E belt must match harness in colour.
*The Chestbox is connected directly to the harness via hooks, magnets or other method that will securely mount the box to the suspenders.
*The web belt is optional on this uniform, and may be worn alone or in combination with the standard Officer's belt and buckle.
* If only the web belt is to be worn, a standard Officers type buckle with affixed greeblie shall be mounted directly to the web belt buckle.| | }}

{{CRLtemplate|File:181st_type_A_chestbox.jpg|Type A Chestbox|
*Two types of chestbox are approved for 501st Legion use.
*The chestbox will have the same configuration as shown in the photo.
*Type A box is rectangular in shape, not square. It is permissible to have a flange that extends ½ “ (12.5mm) around the backside of the chestbox.
*The third hose connection exits the bottom of the box, slightly to the left of wearer’s center. The third hose shall be 1.25” in diameter. The free end of the bottom hose shall be worn connected to the belt at the wearers left hip and terminate in a quick-disconnect assembly, black-painted thermal detonator/O2 canister, or other means of hiding the hose’s opening..
* A communications wire exits the box to the right of the third hose exit point and will be wrapped around the third hose.
*Two curved 45 degree, angled hose connectors exit at the sides of the box, just above the angle of the bottom plate. These may swivel to accommodate the hose when the helmet is worn.
*The box has 4 1" square x 1/8th" thick detail pieces. surrounded by a ⅛” wide white stripe. Accepted colors are grey, white, blue , blue.
*Three rocker switches are mounted to the wearer’s left front of the box. correct colors are grey, white, grey.
*Two circular red and white “lights” are mounted near the top of the front of the box. | | }}

{{CRLtemplate|File:181st_type_B_chestbox.jpg|Type B Chestbox|
*The chestbox is required to have the same configurations as seen in the photo.
*Type B box front vertical plate is rectangular with a beveled lower plate angling toward wearer. The beveled plate has the communications wire connection near the hose mount. The communications wire shall be wrapped around the third hose.
*Two curved 45 degree, angled hose connectors exit at the sides of the box, just above the angle of the bottom plate. These may swivel to accommodate the hose when the helmet is worn.
*A third hose is mounted to its own connector at the bottom of the box, slightly to the left of wearers center. The hose is worn draped to the left, terminating on the wearers left hip and terminate in a quick-disconnect assembly, black-painted thermal detonator/O2 canister, or other means of hiding the hose’s opening.. Hose size shall be between 1.25” and 2” diameter.
*The box has four rectangular plates mounted to the wearer’s left. One white, three grey are accepted. A ⅛” wide white rectangular strip surrounds these.
*The box has 6 white rocker switches, on the wearer’s right side of the box.
*A single greeblie similar to a audio jack is mounted on the front of the box.
*Two circular white “lights” are mounted above the rocker switches. | | }}

{{CRLtemplate|File:181st_harness.jpg|Ejection Harness|
*Gray 2” webbing extending from the below front flak vest to the back vest below the crotch.
*Two loops wrap around each leg at the knees and are attached to the rest of the webbing below the crotch.
*Gray 2” elastic may be substituted for grey webbing.| | }}

{{CRLofficerbelt}}

{{CRLblack-gauntlet-gloves}}

{{CRLgeneric-black-boots}}

{{CRLaccessories}}

{{CRLcommpad}}

{{CRLdl44}}

{{CRLgeneric-e11}}

{{CRLgenericholster}}

{{CRLtemplate|File:TK_anh_stunt_neckseal.jpeg|Neck Seal|
*Artwork depicts pilots of the 181st Fighter Group with a Stormtrooper style neckseal worn under the flight suit.
*Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to the top of the Adam's apple.| | }}

{{CRLtemplate|File:no picl.jpg|Kneepads|
*Kneepads as depicted in the original artwork are optional . The art depicts them as similar to Biker Scout kneepads with no indentations and small extensions at the sides.| | }}

{{CRLfooter|JRS_CRL|T}}

181st Flightsuit guide

2013-05-18T05:53:29Z

Muppet: Created page with "500px"

[[File:181st_flightsuit_guide.jpg|500px]]

181st Flightsuite guide

2013-05-18T05:50:01Z

Muppet: Created page with "500px"

[[File:181st_flightsuit_guide.jpg|500px]]

181st:

2013-05-18T05:39:51Z

2013-04-14T07:57:17Z

Muppet:

File:Snaggletooth full.jpg

2013-04-14T07:57:17Z

Muppet:

2013-04-05T07:47:41Z

Muppet:

Costuming:TA AT-AT Commander

2013-04-03T23:03:14Z

Muppet:

{{CRLheader|AT-AT Commander|File:AT-AT_Commander.jpg| TA9408|Ian Parlett}}

{{CRLdetinfo| 1106 |AT-AT Commander|TA|Star Wars Episode V|These officers command the Imperial Walkers. }}

{{CRLacdlevels}}

{{CRLwipgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:AT-AT_Commander_Helmet.jpg|Helmet|
* Open face helmet based on the shell of Snowtrooper/Snow Cmdr. and AT-ST Driver. The base consists of the dome with rim and helmet skirt.
* The helmet is to be painted in Grey-Green or Gray colour.
* Imperial Code Disks are positioned on both sides of the helmet skirt.
* A "Rangefinder" is attached centered to the right side of the dome aligned to the rim
* A black trim is covering the edge of the helmet skirt and forehead of the dome
* Black elastic/fabric Chin strap. Please not there is NO chin cup unlike the AT-ST helmet.
* There are 6 screw cover greeblies positioned equally around the bottom of the helmet skirt (3 on each side)
* Silver/metallic cylindric 'Spine shaped Greeblie' bar in the rear centre of the helmet skirt. The bar is divided in 11 segments with the thicker 6 segments ideally fitting into the 6 depressions of the helmet skirt.
* There are 5 flat rectangular clips, positioned equally around the helmet where the dome meets the skirt. (1 in the centre, 2 on each side)|
* Fold down comm-link Microphone, attached to RH inner side of helmet in a curved shape with a small conical end. Painted in Black | }}

{{CRLtemplate|File:AT-AT_Commander_Goggles.jpg|Goggles|
*Black trimmed military style goggles, with a Light Gray/Tan strap.|
*Goggles should be angular, and not rounded in shape.
*Strap should be light Gray, and approx 1.5cm in width, with a small buckle on both sides.| }}

{{CRLtemplate|File:AT-AT_Commander_Armour.jpg|Armor|
* Snowtrooper Chest plate, painted to match the Helmet.
* There are 2 Red square greeblies on the right of the centre depression, and 2 White squares on the left side (refer to illustration)
* Three gray knobs and one red knob on the right side of the chest plate
* Red, Gray and White knobs on the left side, just to the left of the centre depression.
* TIE/AT-AT driver style back armor (similar to TK but with a larger, flat box on the rear), painted to match the Helmet.
* Circuit Board detail plate on rear of back armor, with Custom back detail and greeblies (refer to illustration)
* Snowtrooper Style ribbed shoulder bridges connecting the front and back armour plates, painted to match the helmet and armor. There are 3 small screw cover greeblies in a triangular formation at the front of the strap, and one at the rear of each strap.|
*Green/Olive webbing approx 1.5cm in width, passing under the arm, connecting chest & back plates. There is a silver popper on the webbing approx 1" from the back-plate. | }}

{{CRLtemplate|File:ID_tunic.jpg|Tunic|
*Fabric should be a medium weight suiting material exactly matching the pants and hat. Gabardine style weave is most accurate. Color must be olive-greyish green.
*Tunic is double-breasted with a left over right closure on the tapered yoke.
*Yoke comes up across the shoulder to the top shoulder seam.
*The standing collar has square corners and is about 1.25" (31.8 mm) tall and closes snugly and includes a modesty panel behind closure. Collar edges are closed with two eye hooks.
*There are code cylinder pockets on both outside panels of the jacket from about half way between the top and bottom on the arm hole.
*Sleeves are long, and without decoration, cuffs or buttons, containing 2 seams, one along the bottom and one along the back.
*Tunic should be constructed with no top-stitching (stitches visible on the exterior surface of fabric)|
*There is a dart of about 2" (50.8 mm) in the top center of the yoke.
*Additionally there is a seam running the entire circumference of the tunic, dividing it along a line hidden by the uniform belt.
*The back of the tunic has princess seams that run vertically and turn outward to intersect the arm-hole seam at the vertical center.|}}

{{CRLtemplate|File:AT-AT_Commander_Rank_Badge.jpg|Rank Buttons|
* Worn on the top left section of the chest.
* Rank consists of coloured plastic tiles, mounted directly onto the chest armour (no metal bar).
*Any rank upto a General, but no higher.
* Tile dimentions are, H 1/2" (12.7mm). W 3/4" (19mm). D 1/8" (3.2mm).
* Each tile spaced approx 3mm appart.
* Rank tiles are translucent. Colour, quantity & combinations are determined by rank. |
*General rank only .
| }}

{{CRLtemplate|File:ID_gloves.jpg|Gloves|
*Black, leather or leather-like, enclosed fingered, non-textured, gauntlet length and fitted.
*No buckles, straps, etc.||}}

{{CRLtemplate|File:AT-AT_Commander_Belt.jpg|Belt|
* Snowtrooper style abdomen plate, painted to match Helmet and Armor, with circular loop pattern in the centre
* Secured by a Black leather belt, approximately 2" wide.
* Visible adjustment holes on the belt are acceptable.| | }}

{{CRLtemplate|File:ID_pants.jpg|Pants|
*Fabric should be a medium weight suiting material exactly matching the tunic and hat. Gabardine style weave is most accurate. Color options are black or olive-greyish green.
*Flared riding breeches are canon, with semi-stiff flares to the hip/thigh area for grey/green officer types. Breeches must be worn with boots (see below).
*''Straight-legged dress trousers are permitted for black-uniformed officers, but must be worn with quality dress shoes.''
*Pockets are acceptable, though they should not be visible with the tunic on.
*There are no noticeable cuffs on the pants.||}}

{{CRLtemplate|File:ID_boots.jpg|Boots|
*Knee-high, black, lace-less, non-textured, leather or leather-like material. Rubber is not acceptable.
*Both green and black uniforms wear high English dress riding style boots
* Black dress shoes may be worn instead of boots with a black officer uniform and straight legged dress trousers.||}}

{{CRLaccessories}}

{{CRLdh17}}

{{CRLgeneric-e11}}

{{CRLdl44}}

{{CRLgenericholster}}

{{CRLfooter|ACD_CRL|T}}

Costuming:TA AT-AT Commander

2013-04-03T21:04:45Z

Muppet:

Costuming:TA AT-AT Commander

2013-04-01T07:40:22Z

2013-03-25T22:12:42Z

Muppet:

{{CRLheader|Stormtrooper, Return of the Jedi|File:TK_rotj.jpg|TK-4625|Jason Kreis}}

{{CRLdetinfo|1116|Stormtrooper, Return of the Jedi|TK|Episode VI: Return of the Jedi|

'''"An entire legion of my best troops awaits them". - Emperor Palpatine (ROTJ)'''

Outfitted with newly designed armor and the new series of BlasTech E11's, the Stormtroopers were the main garrison for the newly constructed, second Death Star. The Emperor stationed the Empires’ finest Legion of Stormtroopers to defend the defense shield for the Death Star. They were the main strike unit during the battle on the Forest Moon of Endor.

These highly trained elite soldiers cannot be bribed or swayed from their dedication to the Empire.

The Stormtroopers are not only the first strike team units sent into critical combat situations, but are also assigned to keep a watchful eye over the Imperial officers who might betray the Emperor’s cause.

Garrisons of Stormtroopers are stationed on worlds throughout the Galaxy to keep order, and stop any Rebel uprisings.

Even though the Stormtroopers are an independent unit, having their own command structure, ranking system and support facilities, they still serve on Imperial vessels, and operate along side the Imperial army and navy.

The Stormtroopers are shielded by hardened, plastoid,composite armor, fitted over a black environmental body glove, with a built-in life support system. The imposing white armor not only protects them from harsh environments, but also gives limited protection from blaster fire.

Stormtroopers carry an array of equipment and weapons ,wielding blaster rifles and pistols with great skill.

The Stormtroopers, having the combined training and battle tactics of both an Army soldier and a Marine, makes them highly adaptable and a very skilled force.

Rebellion slang terms and nicknames for Stormtroopers:

Whitehats

Plastic Soldiers

Boys in White

Plastic Boys

Stormies

}}

{{CRLfisdlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:TK_rotj_helmet.jpg|Helmet|
*Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray.
*Rear traps and tears have vertical black lines.
*Lenses may be flat or bubble, smoke or green in color, sufficiently dark enough to obscure the costumer's eyes.
*The "ear" bars have three or four bumps, and shall be gray or painted gray, with a black outline. Painting the bumps with rank stripes (Highlighted) in black is optional.
*Frown is painted black and overlaps the teeth area. Eight total teeth on the frown are cut out.
*Tube stripes are medium blue, should be 13 per side, but can be between 9 and 16 per side with the curve bends extending backwards.
*Vocoder (vertically ribbed chin detail) is painted black.
*Aerators/Hovi mix tips (cylinders on either side of the vocoder) are black or painted black.
*Tears, traps, and tube stripes should be decals, but can be hand painted, or decals that replicate hand painted.
*Mesh may be used behind the frown to obscure the face of the wearer.
*Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
*Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary. Please visit FISD/whitearmor.net for more info on these modifications.|
*Ears shall have no visible screws per side.
*Traps/tears and tube stripes shall be decals (with the correct ROTJ details), not hand-painted or decals that replicate hand painted.
*Traps/tears may be either ANH gray or a slightly bluer shade of ANH gray.
*The ends of the frown shall be rounded, not tapered to points (not like ANH/ESB) and not squared ended like the ESB MKII.
*Ear bars shall have four bumps only, not three.
*Correct 'Hovi mic' aerator tips.
*FX helmets are not allowed.|
*MRCE and/or EFX PCR helmets are not allowed.
*ANHv2 helmets are not allowed.
*Lenses shall be bubble green only.
*Ear bars shall have only one or two bumps painted in black (rank stripes).
*Neck trim shall be of an s-type profile rather than a u-type profile. }}

{{CRLtemplate|File:TK_anh_stunt_neckseal.jpeg|Neck Seal|
*Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to the top of the Adam's apple.| | }}

{{CRLtemplate|File:TK_anh_stunt_shoulders.jpeg|Shoulder Straps|
*These shall be securely mounted in front and may free float in back. They may be affixed with rivets, Velcro, or adhesive.|
*No visible rivets are allowed.
*Shoulder straps shall not have a flat end at the ends of them. They shall be ribbed 100%.|
*These shall be affixed in the front (no snaps, rivets or brads shall be visible).
*These shall be affixed in the back (no snaps, rivets or brads shall be visible).}}

{{CRLtemplate|File:TK_rotj_shoulderbells.jpg|Shoulder Bells|
*One on each shoulder. The shoulder bells are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders.|
*Shoulder bells are rounded at the corners.
*Shoulder bell straps 1/4"(6.3mm)wide shall be present, worn higher and shall not be visible across the biceps armor like in ANH.|
*Shoulder bells shall have foam padding inside.
*Shoulder bells shall be slightly pinched and should be worn slightly higher, compared to ANH/ESB.}}

{{CRLtemplate|File:TK_anh_stunt_biceps.jpeg|Biceps|
*Biceps are fully closed.| | }}

{{CRLtemplate|File:TK_anh_stunt_forearms.jpeg|Forearms|
*Forearms are fully closed.| |
*No return edge on the inside of the front of the forearm is allowed.
}}

{{CRLtemplate|File:TK_esb_handplates.jpeg|Hand Plates|
*These shall be clam shell, or snowtrooper-style hand plates and not the trapezoidal design seen in A New Hope. The hand plates are mounted securely over the back of the glove.| | }}

{{CRLtemplate|File:TK_anh_stunt_gloves.jpeg|Gloves|
*Black in color, made of either rubber, nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured.| |
*Gloves shall be rubber or rubber like chemical gloves in black.}}

{{CRLtemplate|File:TK_rotj_chest.jpeg|Chest|
*Chest plate overlaps the abdominal plate.
*A white flexible U shaped gasket or molded lip shall be present around all edges.||
*Fabric or elastic strip connecting chest to back shall be either black or not present.
*Ideally the AM/FX style chest plate should be replaced with a more screen accurate type. If using an AM/FX style chest plate, it shall be trimmed at the bottom and sides to eliminate the over elongated appearance and to give a more accurate look (Note: Return edge is not required but shall have the rubber gasket).}}

{{CRLtemplate|File:TK_rotj_back.jpeg|Back|
*Back plate contains a "O II" design.
*A white flexible U shaped gasket or molded lip shall be present around all edges. ||
*Back plate shall have no, or minimal overlap of the kidney plate.
*Ideally the AM/FX style back plate should be replaced with a more screen accurate type. If using an AM/FX style back plate it shall have no, or minimal overlap of the kidney plate and shall be reshaped to emulate a screen used back plate by properly trimming and re-shaping (stretching) the left and right edges of the armor to contour to your body. (Note:Return edge is not required but shall have the rubber gasket). Note: There is currently no tutorial available for this, but you can see an example of this Mod and visual comparison at whitearmor.net}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
*Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs.| | }}

{{CRLtemplate|File:TK_rotj_ab.jpg|Abdomen Plate|
*A white flexible U shaped gasket or molded lip shall be present around all edges.
*The ab plate has a button area that matches the color pattern shown (3 dark blue + 6 charcoal grey or black); buttons are approximately 7/16" (11mm) in diameter. The three dark blue buttons will be the three buttons closest to the belt.
*Ab plate button detail shall be inverted compared to ANH/ESB. |
|
*There shall be no visible split rivet/brad on the cod/crotch and no visible rivets or brads on the left or right side of the ab plate, unlike ANH/ESB.}}

{{CRLtemplate|File:TK_rotj_butt.jpg|Kidney & Butt Plate|
*A white flexible U shaped gasket or molded lip shall be present around all edges.
*A separate kidney/butt plate is not allowed - the kidney and butt plate shall be combined/fused to a single plate/one piece.
*The crotch tab of the butt plate area may or may not have visible snaps.|
*The edges of the hip area should be rounded/curved (not like the straight lines found on the ANH/ESB butt plate).|
*There shall be no visible side rivets on the kidney plate, unlike ANH/ESB suits.
*There shall be no visible snaps, rivets or brads on the crotch tab of the butt plate tab. }}

{{CRLtemplate|File:ROTJ Belt.jpg|Belt|
*Belt face is made of plastic (TK ammo belt).
*The soft belt proper is tightly woven nylon/cordura like/style material or material with a tightly woven nylon/cordura like/style covering. Size must be 2.25" (57mm) to 2.5" (64mm) wide. The color is to be white to off-white.
*The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.|
.|
*There shall be no square buttons covering the belt rivets (there shall be two rivets, one on each side of the ammo belt).
*Corners of ammo belt shall be cut at right angles, not 45 degrees as in ANH/ESB.
*Drop boxes are closed in the back.
}}

{{CRLtemplate|File:TK_anh_stunt_detonator.jpeg|Thermal Detonator|
*(A.K.A. O2 canister) attaches to the center back of the belt. This is an all gray cylinder without silver stickers or silver paint. The cylinder is between 2” (50mm) and 2.68"(68mm) in diameter with white end caps on each end. The white control panel pad faces upwards, with controls/round washer style detail closest to the right end cap. The total length should be approximately 7.50" (190.5mm).
*The thermal detonator shall be attached via metal or metallic-appearing clips approximately 3/4" (19mm) wide.| |
*The thermal detonator control panel shall have correct ROTJ details, not ANH/ESB. }}

{{CRLtemplate|File:TK_anh_stunt_thighs.jpeg|Thighs|
*Thigh armor shall be closed in the back.
*The ammo belt shall be installed on the bottom of the right thigh.| |
*The thigh ammo belt shall be standard rivets.
*The bottom corners of the thigh ammo belt shall be rounded off.}}

{{CRLtemplate|File:TK_anh_stunt_shins.jpeg|Lower Legs|
*Greaves close in the back. The trapezoid knee plate (sniper knee plate) is affixed to the left greave and may have two visible brads or rivets securing it to the greave.
*The AM greaves (shins) shall be on the proper legs, with a new cover strip. The cover strip edge shall be facing the inside of the leg. Note: There is a manufacturer defect with the AM greaves (shins) that may cause you to wear the them improperly. Please see the Tutorial titled :"AM armor shins: the proper way to assemble and wear", on the whitearmor.net| | }}

{{CRLtemplate|File:TK_anh_stunt_boots.jpeg|Boots|
*White leather or leather-like, above ankle height, with a flat sole with a short heel, and small U-shaped elastic sections on both sides of the ankle with no buckles or laces. Jodhpur/Chelsea-type boots or an equivalent style is acceptable. Elvis or Mariachi boots are not allowed. .| |
*There shall be no seam on the front of the boot (e.g. CABoots are not allowed).
*Boots shall be lightly scuffed.
*Boots shall have a white sole (can be painted).}}

{{CRLtemplate|File:ROTJ holster.jpg|Holster|
*Holster may be omitted from the costume. If a holster is worn, it must be made of completely black leather or leather-like material, and worn on the right side of belt and be attached via the straps behind the belt using two fasteners in the middle of the belt .The fasteners may be rivets, snaps, or Chicago screws. (note: the straps are a little longer for the ROTJ holster, then seen on the other Original Trilogy Stormtroopers).
.|

.|
.}}

{{CRLaccessories}}

{{CRLtemplate|File:TK_rotj_e11.jpg|BlasTech E-11|
*Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.|
*Folding stock (does not need to function).
*No ammo counter shall be present.
*D-ring mounted on the rear.
*Correct style scope.
*No power cylinders on the magazine housing.
*Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 7 U shaped channels on blaster (all holes on barrel shall be covered).
*If using the popular commercially available Stormtrooper blasters, you shall grind off the T-tracks and replace them with U shaped channels and cover the open rows of holes (total of 7 U shaped channels in all).
*Correct greeblies on the left rear area shall be present (door catch and two "hammers").|
*Hasbro blasters are not allowed, even conversions.
*Forward D-ring shall be mounted underneath the front sight on the left side of the barrel.
*Use of the correct front sight (which differs from ANH and ESB).
*The scope rail is unique to ROTJ E11 and is not like the normal open ANH/ESB scope rails, but is a solid, one piece, with a unique sight design on the front. The scope connects to the notched out area of the solid rail. The scope shall be the correct design (as the ones seen in ROTJ), and shall attach to the scope rail via one scope mount.
*The muzzle will be unlike the normal ANH style. It shall be flat with two counter sunk Allen bolts (one located at the four o’clock position and one located at the ten ‘o’clock position).
*The door catch shall be correct, not a "close enough" attempt as seen on the Cinemastery blaster.
}}

{{CRLfooter|FISD_CRL|T}}

Costuming:TK esb

2013-03-25T22:11:47Z

Muppet:

{{CRLheader|Stormtrooper, Empire Strikes Back|File:ESBtk.jpg|TK-7795|Jason M Kreis TK-4625}}

{{CRLdetinfo|1116|Stormtrooper, Empire Strikes Back|TK|Episode V: The Empire Strikes Back|

'''“It would be unfortunate if I had to leave a garrison here”. - Darth Vader (ESB)'''

The Stormtroopers were the main force during the capture and interrogation of the Rebels, Han Solo, Princess Leia Organa, Chewbacca and their droid C3PO on the Cloud City of Bespin.

These highly trained elite soldiers cannot be bribed or swayed from their dedication to the Empire.

The Stormtroopers are not only the first strike team units sent into critical combat situations, but are also assigned to keep a watchful eye over the Imperial officers who might betray the Emperor’s cause.

Garrisons of Stormtroopers are stationed on worlds throughout the Galaxy to keep order, and stop any Rebel uprisings.

Even though the Stormtroopers are an independent unit, having their own command structure, ranking system and support facilities, they still serve on Imperial vessels, and operate along side the Imperial army and navy.

The Stormtroopers are shielded by hardened, plastoid,composite armor, fitted over a black environmental body glove, with a built-in life support system. The imposing white armor not only protects them from harsh environments, but also gives limited protection from blaster fire.

Stormtroopers carry an array of equipment and weapons ,wielding blaster rifles and pistols with great skill.

The Stormtroopers, having the combined training and battle tactics of both an Army soldier and a Marine, makes them highly adaptable and a very skilled force.

Rebellion slang terms and nicknames for Stormtroopers:

Whitehats

Plastic Soldiers

Boys in White

Plastic Boys

Stormies

}}

{{CRLfisdlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:TK_esb_helmet.jpeg|Helmet|
*Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray.
*Rear traps and tears have vertical black lines.
*Lenses are a flat smoke or green sufficiently dark enough to obscure the costumer's eyes.
*The “ear” bars have three or four bumps and should be gray or painted gray, with a black outline. Painting the bumps with rank stripes (highlighted) in black is optional.
*Frown is painted black and does not leave the teeth area. Eight or six total teeth on the frown are cut out.
*Tube stripes are medium blue, should be 13 per side, but can be 9 and 16 per side with the curve bends extending backwards.
*Vocoder (vertically ribbed chin detail) is painted black.
*Aerators/Hovi mix tips (cylinders on either side of the vocoder) are black or painted black.
*Tears, traps, and tube stripes should be decals but can be hand painted, or decals that replicate hand painted.
*Mesh may be used behind the frown to obscure the face of the wearer.
*Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
*Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary. Please visit FISD/whitearmor.net for more info on these modifications. |
*Ears shall have three screws used per side, one above and below the ear bar and one at the base of the helmet.
*Traps/tears and tube stripes shall be decals (with the correct ESB details), no hand-painting or decals that replicate hand painted.
*Traps/tears may be either ANH gray or a slightly bluer shade of ANH gray.
*Ear bars shall have four bumps only, not three.
*Correct 'Hovi mic' aerator tips.
*FX helmets are not allowed.|
*MRCE and/or EFX PCR helmets are not allowed.
*ANHv2 helmets are not allowed.
*Ear bars shall have only two bumps painted in black (rank stripes).
*Neck trim shall be of an s-type profile rather than a u-type profile. }}

{{CRLtemplate|File:TK_anh_stunt_neckseal.jpeg|Neck Seal|
*Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to the top of the Adam's apple.| | }}

{{CRLtemplate|File:TK_anh_stunt_shoulders.jpeg|Shoulder Straps|
*These shall be securely mounted in front and may free float in back. They may be affixed with rivets, Velcro, or adhesive.|
*No visible rivets are allowed.|
*These shall be glued in front.
*These shall be affixed in the back (no snaps, rivets or brads shall be visible).
*Straps shall not have a white elastic band securing the shoulder straps to either the chest/back.}}

{{CRLtemplate|File:TK_anh_stunt_shoulder.jpeg|Shoulder Bells|
*One on each shoulder. The shoulder bells are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders.|
*Ideally no shoulder bell straps across the biceps.If there is a shoulder bell strap, it shall not be visible across the biceps. | }}

{{CRLtemplate|File:TK_anh_stunt_biceps.jpeg|Biceps|
*Biceps are fully closed.| |}}

{{CRLtemplate|File:TK_anh_stunt_forearms.jpeg|Forearms|
*Forearms are fully closed.| |
*No return edge on the inside of the front of the forearm is allowed.
}}

{{CRLtemplate|File:TK_esb_handplates.jpeg|Hand Plates|
*These shall be clam shell, or snowtrooper-style hand plates and not the trapezoidal design seen in A New Hope. The hand plates shall be mounted securely over the back of the glove.| |
*If rubber gloves are worn the hand plates shall be affixed via an elastic strap over the palm.
*If silk or satin gloves are worn, the hand plates shall have the correct visible stitching pattern using black cotton, with a five point/star pattern, equally spread out with 2 on each side and 1 in the middle front, and needs to be double stitched at each point.
}}

{{CRLtemplate|File:TK_anh_stunt_gloves.jpeg|Gloves|
*Black in color, made of either rubber, nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured. | |
*Gloves shall be black rubber or rubber- like chemical gloves or black silk or satin.
}}

{{CRLtemplate|File:TK_anh_stunt_chest.jpeg|Chest|
*Chest plate overlaps the abdominal plate. | |
*Chest and back shall be connected with a white fabric or preferably elastic strap at the shoulders.
*Ideally the AM/FX style chest plate should be replaced with a more screen accurate type. If using an AM/FX style chest plate, the bottom and sides shall be trimmed and a new return edge shall be added at the bottom to eliminate the over elongated appearance and to give a more accurate look. See the tutorial: http://www.whitearmor.net/fisd/Tutorial-chestback
}}

{{CRLtemplate|File:TK_anh_stunt_back.jpeg|Back|
*Back plate contains a "O II" design.| |
*Back plate shall have no, or minimal overlap of the kidney plate.
*Ideally the AM/FX style back plate should be replaced with a more screen accurate type. If using an AM/FX style back plate it shall have no, or minimal overlap of the kidney plate. and shall be reshaped to emulate a screen used back plate by properly trimming and re-shaping (stretching) the left and right edges of the armor to contour to your body. Note: There is currently no tutorial available for this, but you can see an example of this Mod and visual comparison at whitearmor.net
}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
*Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs.| | }}

{{CRLtemplate|File:TK_anh_stunt_ab.jpeg|Abdomen Plate|
*The ab plate has a button area that matches the color pattern shown (3 blue + 6 gray); buttons are approximately 7/16"(11mm) in diameter. |
*Any gap between the ab and kidney plate shall be no more than 1/2"(12.5mm) wide. Any shims used to achieve this effect should be of a similar material and color as the ab and kidney plate. Shims shall fit flush and seams are allowed.|
*Ideally there should be no gap between the ab and kidney plates, just a single visible seam line.
*Rivets on the left side of the ab plate: a total of three rivets, the heads should be approximately 5/16" (8mm) diameter and equally spaced out along the depth of the armor and about 10mm from the edge. They may be painted white, or not. Note:For the original used TK armor, this type of rivets where, bifurcated rivets or split rivet.
*A single male snap on the top right corner of the ab plate shall be present.
*A single split rivet or brad shall be present on the crotch tab of the ab plate. It does not need to be functional.
}}

{{CRLtemplate|File:TK_anh_stunt_kidney.jpeg|Kidney Plate|
*A separate kidney plate shall be present, split from the butt plate. |.|
*Three rivets shall be present on the left side of the kidney plate, the heads should be approximately 5/16"(8mm) diameter and equally spaced out along the depth of the armor and about 10mm from the edge. They may be painted white, or not. Note: For the original used TK armor, this type of rivets where, bifurcated rivets or split rivet.
}}

{{CRLtemplate|File:TK_anh_stunt_butt.jpeg|Butt Plate|
*A separate butt plate is required, split from the kidney plate. |
.|
*Two male snaps shall be present on the crotch tab of the butt plate. They do not need to be functional.
}}

{{CRLtemplate|File:TK_anh_stunt_belt.jpeg|Belt|
*Belt face is made of plastic (TK ammo belt).
*The soft belt proper is made of canvas, or material with a canvas covering. Size must be 2.75” (70 mm) to 3.25”(83 mm) wide and not wider than the plastic portion of the belt. The color is be white to off-white.
*The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.|
*There shall be three square buttons, one centered in the middle and one on each end of the plastic ammo belt.|
*Drop boxes are closed in the back.
*The corners of the of the plastic ammo belt shall be trimmed at a 45 degree angle.}}

{{CRLtemplate|File:TK_anh_stunt_detonator.jpeg|Thermal Detonator|
*(A.K.A. O2 canister) attaches to the center back of the belt. This is an all gray cylinder without silver stickers or silver paint. The cylinder is between 2” (50mm) and 2.68"(68mm) in diameter with white end caps on each end. The white control panel pad faces upwards, with controls/round washer style detail closest to the right end cap. The total length should be approximately 7.50" (190.5mm).
*The thermal detonator shall be attached via metal or metallic-appearing clips approximately 1" (25mm) wide. || }}

{{CRLtemplate|File:TK_anh_stunt_thighs.jpeg|Thighs|
*Thigh armor shall be closed in the back.
*The small ammo belt is installed on the bottom of the right thigh.| |
*The thigh ammo belt shall be connected by brads/split rivets only – but not by standard rivets.
*The bottom corners of the thigh ammo belt shall be rounded off.}}

{{CRLtemplate|File:TK_anh_stunt_shins.jpeg|Lower Legs|
*Greaves close in the back. The trapezoid knee plate (sniper knee plate) is affixed to the left greave and may have two visible brads or rivets securing it to the greave.
*The AM greaves (shins) shall be on the proper legs, with a new cover strip. The cover strip edge shall be facing the inside of the leg. Note: There is a manufacturer defect with the AM greaves (shins) that may cause you to wear the them improperly. Please see the Tutorial titled :"AM armor shins: the proper way to assemble and wear", on the whitearmor.net | |
*Ideally there should be no visible rivets or brads used to secure the sniper plate to the left greave.}}

{{CRLtemplate|File:TK_anh_stunt_boots.jpeg|Boots|
*White leather or leather-like, above ankle height, with a flat sole with a short heel, and small U-shaped elastic sections on both sides of the ankle with no buckles or laces. Jodhpur/Chelsea-type boots or an equivalent style is acceptable. Elvis or Mariachi boots are not allowed.| |
*There shall be no seam on the front of the boot (e.g. CABoots are not allowed).
*Boots shall be lightly scuffed.}}

{{CRLtemplate|File:TK_esb_holster.jpeg|Holster|
*Holster is worn on right side of belt. Holster will be made of completely black leather or leather-like material and be worn on the right and affixed via two black loops over the belt (no fasteners).|

.| }}

{{CRLaccessories}}

{{CRLtemplate|File:TK_esb_blaster1.jpeg|BlasTech E-11 (canon)|
*Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.|
*Folding stock (does not need to function).
*No ammo counter shall be present.
*D-ring mounted on the rear.
*Correct style scope.
*No power cylinders on the magazine housing.
*Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 6 T-tracks on blaster (leaving the lowest row on the magazine housing side uncovered).
*If using the Hasbro E11 toy blaster and you cover all the rows of holes, the blaster will have 7 T-tracks total. But, if you want to have the correct number of T-tracks (6 total) with the lower row of open vent holes on the magazine housing side, then you shall cover the pre-existing rows of holes with T-tracks, and grind off the lower integrated T-track on the magazine housing side and drill a new row of holes in its place. |
*Hasbro blasters are not allowed, even conversions.}}

{{CRLtemplate|File:TK_esb_blaster2.jpeg|BlasTech E-11 (promo)|
*Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.|
*Folding stock (does not need to function).
*No ammo counter shall be present.
*Correct style scope.
*No power cylinders on the magazine housing.
*Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 6 T-tracks on blaster (leaving the lowest row on the magazine housing side uncovered).
*If using the Hasbro E11 toy blaster and you cover all the rows of holes, the blaster will have 7 T-tracks total. But, if you want to have the correct number of T-tracks (6 total) with the lower row of open vent holes on the magazine housing side, then you shall cover the pre-existing rows of holes with T-tracks, and grind off the lower integrated T-track on the magazine housing side and drill a new row of holes in its place.
*Two greeblies on the left rear area.
*Three studs on the right rear area.
*Add two scope block greeblies.
*Remove front bayonet muzzle disk.
*Remove magazine housing parts.
*Remove D-Ring mount.
*Swoosh trim on right side above the pistol grip.|
*Hasbro blasters are not allowed, even conversions.}}

{{CRLfooter|FISD_CRL|T}}

Costuming:TK anh hero

2013-03-25T22:10:55Z

Muppet:

{{CRLheader|Stormtrooper, ANH Hero|File:TK_anh_hero.jpeg| TK-2886|Terry Chui}}

{{CRLdetinfo|1116|Stormtrooper, ANH Hero|TK|Star Wars Episode IV: A New Hope|

'"This station is now the ultimate power in the universe. I suggest we use it!" - Admiral Motti (ANH)'

Admiral Motti was incorrect in this statement above, about the Death Star. The true ultimate power in the Universe, that the Empire possesses, is the Stormtrooper.

The Stormtroopers (Hero) were a part of the capture of Rebel leader, Princess Leia Organa on the Rebel blockade runner the Tantive IV. They were also dispersed among the main garrison on the first Death Star. The Rebels, Luke Skywalker and Han Solo, stole two of these suits and impersonated TK’s as they were trying to free Princess Leia Organa and escape from the Death Star.

These highly trained elite soldiers cannot be bribed or swayed from their dedication to the Empire.

The Stormtroopers are not only the first strike team units sent into critical combat situations, but are also assigned to keep a watchful eye over the Imperial officers who might betray the Emperor’s cause.

Garrisons of Stormtroopers are stationed on worlds throughout the Galaxy to keep order, and stop any Rebel uprisings.

Even though the Stormtroopers are an independent unit, having their own command structure, ranking system and support facilities, they still serve on Imperial vessels, and operate along side the Imperial army and navy.

The Stormtroopers are shielded by hardened, plastoid,composite armor, fitted over a black environmental body glove, with a built-in life support system. The imposing white armor not only protects them from harsh environments, but also gives limited protection from blaster fire.

Stormtroopers carry an array of equipment and weapons, wielding blaster rifles and pistols with great skill.

The Stormtroopers, having the combined training and battle tactics of both an Army soldier and a Marine, makes them highly adaptable and a very skilled force.

Rebellion slang terms and nicknames for Stormtroopers:

Whitehats

Plastic Soldiers

Boys in White

Plastic Boys

Stormies

}}

{{CRLfisdlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Tk_anh_hero_helmet.jpg|Helmet|
*Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray.
*Rear traps and tears have vertical black lines.
*Lenses may be flat or bubble, green or smoke, sufficiently dark enough to obscure the costumer's eyes.
*The “ear” bars may have three or four bumps and should be gray or painted gray, with a black outline. Painting the bumps with a rank stripe (highlighted) in black is optional.
*Frown is painted gray and does not leave the teeth area. Six total teeth on the frown are cut out and the frown is tapered at the ends.
*Tube stripes are medium blue, should be 11 or 13 per side but can be between 9 and 16 per side with the curve bends extending backwards.
*Vocoder (vertically ribbed chin detail) is painted black.
*Aerators/Hovi mix tips (cylinders on either side of the vocoder) are black or painted black.
*Tears, traps, and tube stripes may be hand painted, decals, or decals that replicate hand painted.
*Mesh may be used behind the frown to obscure the face of the wearer.
*Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
*Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary. Please visit FISD/whitearmor.net for more info on these modifications.|
*Lenses must be green bubble or smoke bubble only.
*Ears shall have two screws per side, one above the ear bar and one at the base of the helmet.
*Ear bars should have three bumps only, not four.
*Traps/tears and tube stripes shall have the correct ANH TK details.
*Correct 'Hovi mic' aerator tips.
*FX helmets are not allowed.|
*MRCE and/or EFX PCR helmets are not allowed.
*ANHv2 helmets are not allowed.
*Ear bars shall have only one or two bumps painted in black (rank stripes).
*Neck trim shall be of an s-type profile rather than a u-type profile.
*Tears/traps shall be hand painted or use decals that emulate hand painted (with correct ANH TK details). }}

{{CRLtemplate|File:TK_anh_stunt_neckseal.jpeg|Neck Seal|
*Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to the top of the Adam's apple.| |
*Neck seal shall include a front and back fabric bib that goes over the undersuit, but does not cover the sides of the body.
}}

{{CRLtemplate|File:TK_anh_stunt_shoulders.jpeg|Shoulder Straps|
*These shall be securely mounted in front and may free float in back. They may be affixed with rivets, Velcro, or adhesive.|
*No visible rivets are allowed.|
*These shall free float in back.
*These shall be glued in front.
*The plastic shoulder straps need to be held down in the back via a white elastic band to the white fabric that connects/bridges the chest and back piece.}}

{{CRLtemplate|File:TK_anh_stunt_shoulder.jpeg|Shoulder Bells|
*One on each shoulder. The shoulder bells are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders and should have a black elastic strap that wraps around the inside of the bicep.| |
*If your shoulder bells have the swoop, the left shoulder bell ” swoop” should point forward toward the chest, and the right shoulder bell ”swoop” should point backwards toward the back plate.
}}

{{CRLtemplate|File:TK_anh_stunt_biceps.jpeg|Biceps|
*Biceps are fully closed.| |}}

{{CRLtemplate|File:TK_anh_stunt_forearms.jpeg|Forearms|
*Forearms are fully closed.| |
*No return edge on the inside of the front of the forearm is allowed.
}}

{{CRLtemplate|File:TK_anh_stunt_handplates.jpeg|Hand Plates|
*Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material.| |
*Hand guards shall be latex or latex-like, painted white, affixed to rubber gloves in lieu of plastic hand guards.
}}

{{CRLtemplate|File:TK_anh_stunt_gloves.jpeg|Gloves|
*Black in color, made of either rubber, nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured.| |
*Gloves shall be rubber or rubber-like chemical gloves, in black. }}

{{CRLtemplate|File:TK_anh_stunt_chest.jpeg|Chest|
*Chest plate overlaps the abdominal plate | |
*Chest and back shall be connected with a white fabric or preferably elastic strap at the shoulders.
*Ideally the AM/FX style chest plate should be replaced with a more screen accurate type. If using an AM/FX style chest plate, the bottom and sides shall be trimmed and a new return edge shall be added at the bottom to eliminate the over elongated appearance and to give a more accurate look. See the tutorial: http://www.whitearmor.net/fisd/Tutorial-chestback
}}

{{CRLtemplate|File:TK_anh_stunt_back.jpeg|Back|
*Back plate contains a "O II" design.| |
*Back plate shall have no, or minimal overlap of the kidney plate.
*Ideally the AM/FX style back plate should be replaced with a more screen accurate type. If using an AM/FX style back plate it shall have no, or minimal overlap of the kidney plate. and shall be reshaped to emulate a screen used back plate by properly trimming and re-shaping (stretching) the left and right edges of the armor to contour to your body. Note: There is currently no tutorial available for this, but you can see an example of this Mod and visual comparison at whitearmor.net
}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
*Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs.| | }}

{{CRLtemplate|File:TK_anh_stunt_ab.jpeg|Abdomen Plate|
*The ab plate has a button area that matches the color pattern shown (3 blue + 6 gray); buttons are approximately 7/16" (11mm) in diameter. |
*Any gap between the ab and kidney plate shall be no more than 1/2" (12.5mm) wide. Any shims used to achieve this effect should be of a similar material and color as the ab and kidney plate. Shims shall fit flush and seams are allowed.|
*Ideally there should be no gap between the ab and kidney plates, just a single visible seam line.
*Rivets on the left side of the ab plate: a total of three rivets, the heads should be approximately 5/16"(8mm) diameter and equally spaced out along the depth of the armor and about 10mm from the edge. They may be painted white, or not. Note:For the original used TK armor, this type of rivets where, bifurcated rivets or split rivet.
*A single male snap on the top right corner of the ab plate shall be present.
*A single split rivet or brad shall be present on the crotch tab of the ab plate. It does not need to be functional.
}}

{{CRLtemplate|File:TK_anh_stunt_kidney.jpeg|Kidney Plate|
*A separate kidney plate shall be present, split from the butt plate. ||
*Three rivets shall be present on the left side of the kidney plate, the heads should be approximately 5/16" (8mm) diameter and equally spaced out along the depth of the armor and about 10mm from the edge. They may be painted white, or not. Note: For the original used TK armor, this type of rivets where, bifurcated rivets or split rivet.}}

{{CRLtemplate|File:TK_anh_stunt_butt.jpeg|Butt Plate|
*A separate butt plate is required, split from the kidney plate|
.|
*Two male snaps shall be present on the crotch tab of the butt plate. They do not need to be functional.}}

{{CRLtemplate|File:TK_anh_stunt_belt.jpeg|Belt|
*Belt face is made of plastic (TK ammo belt).
*The soft belt proper is made of canvas, or material with a canvas covering. Size must be 2.75” (70 mm) to 3.25”(83 mm) wide and not wider than the plastic portion of the belt. The color is be white to off-white.
*The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.|
*There shall be three square buttons, one centered in the middle and one on each end of the plastic ammo belt.|
*Drop boxes are closed in the back.
*The corners of the plastic ammo belt shall be trimmed at a 45 degree angle.}}

{{CRLtemplate|File:TK_anh_stunt_detonator.jpeg|Thermal Detonator|
*(A.K.A. O2 canister) attaches to the center back of the belt. This is an all gray cylinder without silver stickers or silver paint. The cylinder is between 2” (50mm) and 2.68"(68mm) in diameter with white end caps on each end. The white control panel pad faces upwards, with controls/round washer style detail closest to the right end cap. The total length should be approximately 7.50" (190.5mm).
*The thermal detonator shall be attached via metal or metallic-appearing clips approximately 1" (25mm) wide.|
| }}

{{CRLtemplate|File:TK_anh_stunt_thighs.jpeg|Thighs|
*Thigh armor shall be closed in the back.
*The small ammo belt is installed on the bottom of the right thigh.| |
*The thigh ammo belt shall be connected by brads/split rivets only – but not by standard rivets.
*The bottom corners of the thigh ammo belt shall be rounded off.}}

{{CRLtemplate|File:TK_anh_stunt_shins.jpeg|Lower Legs|
*Greaves close in the back. The trapezoid knee plate (sniper knee plate) is affixed to the left greave and may have two visible brads or rivets securing it to the greave.
*The AM greaves (shins) shall be on the proper legs, with a new cover strip. The cover strip edge shall be facing the inside of the leg. Note: There is a manufacturer defect with the AM greaves (shins) that may cause you to wear the them improperly. Please see the Tutorial titled :"AM armor shins: the proper way to assemble and wear", on the whitearmor.net | |
*Ideally there should be no visible rivets or brads used to secure the sniper plate to the left greave.}}

{{CRLtemplate|File:TK_anh_stunt_boots.jpeg|Boots|
*White leather or leather-like, above ankle height, with a flat sole with a short heel, and small U-shaped elastic sections on both sides of the ankle with no buckles or laces. Jodhpur/Chelsea-type boots or an equivalent style is acceptable. Elvis or Mariachi boots are not allowed.| |
*There shall be no seam on the front of the boot (e.g. CABoots are not allowed).
*Boots shall be lightly scuffed.}}

{{CRLtemplate|File:TK_anh_stunt_holster.jpeg|Holster|
* Holster is worn on left side of belt. It must be made of black leather or leather-like material, and be attached via two leather or leather-like material straps to the belt from behind instead of front, with no loops covering the outside of the belt.
* The holster must be affixed with four fasteners (Two per strap) Two at the top and two at the bottom of the belt. The fasteners may be rivets, snaps, or Chicago screws .|

.| }}

{{CRLaccessories}}

{{CRLtemplate|File:TK_anh_stunt_e11.jpeg|BlasTech E-11|
*Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.|
*Folding stock (does not need to function).
*A real or replica ammo counter - based off of a Hengstler counter - shall be present.
*D-ring mounted on the rear.
*Correct style scope.
*Two power cylinders on the magazine housing.
*Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 6 T-tracks on blaster (leaving the lowest row on the magazine housing side uncovered).
*If using the Hasbro E11 toy blaster and you cover all the rows of holes, the blaster will have 7 T-tracks total. But, if you want to have the correct number of T-tracks (6 total) with the lower row of open vent holes on the magazine housing side, then you shall cover the pre-existing rows of holes with T-tracks, and grind off the lower integrated T-track on the magazine housing side and drill a new row of holes in its place.
*No ESB/ROTJ greeblies are allowed on the blaster.|
*Hasbro blasters are not allowed, even conversions.}}

{{CRLtemplate|File:TK_anh_stunt_dlt19.jpeg|BlasTech DLT-19 Heavy Blaster Rifle|
*Based on a real or replica MG-34 machine gun |
*A DLT-19 is an MG-34 with T-tracks on the barrel, ejection port cover added, and a small disk on left side.| }}

{{CRLtemplate|File:Tk_anh_hero_grapplinghook.jpg|Grappling Hook/Comlink|
*Grappling hook and comlink (the grappling hook and comlink should be substituted as a set in the place of the thermal detonator, not worn in addition to it).| | }}

{{CRLtemplate|File:Tk_anh_hero_se14r.jpg|BlasTech SE-14R|
*The SE-14R blaster was only seen on promotional pictures. It should have a correct scope if carried in lieu of the E-11 for informal events.| |}}

{{CRLtemplate|File:Tk_anh_hero_lightsaber.jpg|Stormtrooper Lightsaber|
*The TK lightsaber should be as accurate, as seen in Ralph Mcquarrie’s concept illustrations for the movie script entitled: “Star Wars” or originally known as” The Star Wars” The lightsaber has a white or clear blade. It may be carried for informal events only. | | }}

{{CRLfooter|FISD_CRL|T}}

Costuming:TK commander

2013-03-25T22:09:05Z

Muppet:

{{CRLheader|Stormtrooper Commander|File:TK Commander-full.jpg|TK8020|Erik von Oy TK9838}}

{{CRLdetinfo|1116|Stormtrooper Commander (TKC) |TK|The Force Unleashed|

The Stormtrooper Commanders patrol hostile battlefields, leading their troops into fierce combat on dangerous worlds such as the fungus planet Felucia. With razor-sharp minds and steely resolve, these highly trained Imperial soldiers continue the reputation established by the Clone Wars’ fearsome ARC troopers. Clearly visible in their uniquely detailed armor, the Commanders confront enemies such as the savage Felucians with deadly heavy blaster cannons equipped with a devastating stun setting. They are rewarded for their loyalty with specialized armor fitted with an internal shield generator capable of deflecting nearly any attack, with the exeception of a lightsaber. Most importantly, the Stormtrooper Commanders are entrusted with command over the Empire’s elite Shadow Troopers, with authority to call in reinforcements and trigger ambushes without clearance from Imperial high command. Stormtrooper Commanders typically hang back and stun the most threatening enemy, who is then overwhelmed by Shadow Troopers.
}}

{{CRLfisdlevels}}

{{CRLgmlapproval}}

{{CRLtemplate|File:TK Commander Helmet.jpg|Helmet|
*Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray.
*Rear traps and tears have vertical black lines.
*Lenses are flat material, green in color, sufficiently dark enough to obscure the costumer's eyes.
*The “ear” bars have three or four bumps and should be gray or painted gray, with a black outline. Painting the bumps with rank stripes (highlighted) in black is optional.
*Ears shall have a black horizontal anchor-like detail on each side of the ear bar.
*Frown is painted gray and does not leave the teeth area. Eight total teeth on the frown are cut out.
*Tube stripes are medium blue, numbering between 9 and 16 per side with the curve bends extending backwards.
*Vocoder (vertically ribbed chin detail) is painted black.
*Aerators/Hovi mix tips (cylinders on either side of the vocoder) are black or painted black.
*Tears, traps, and tube stripes may be hand painted, decals, or decals that replicate hand painted.
*Blue stripe detail shall be present on the right side of the helmet, starting from the back of the helmet, and continued on to the bottom of the face (stripe tapers to a point as it goes down the face).
*Mesh may be used behind the frown to obscure the face of the wearer.
*Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
*Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary. Please visit FISD/whitearmor.net for more info on these modifications. |
*Ears shall have three screws per side, one above and one below the ear bar and one at the base of the helmet.
*Ear bars should have four bumps only, not three.
*Traps/tears and tube stripes shall have the correct ANH TK details
*Correct 'Hovi mic' aerator tips.
*FX helmets are not allowed.
*Helmet and details/paint should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD).|
*MRCE and/or EFX PCR helmets are not allowed.
*ANHv2 helmets are not allowed.
*Ear bars shall have only one or two bumps painted in black (rank stripes).
*Neck trim shall be of an s-type profile rather than a u-type profile.
*Tears/traps shall be hand painted or use decals that emulate hand painted (with correct ANH TK details). }}

{{CRLtemplate|File:TK_anh_stunt_neckseal.jpeg|Neck Seal|
*Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to the top of the Adam's apple.| | }}

{{CRLtemplate|File:TK Commander Straps.jpg|Shoulder Straps|
*These shall be securely mounted in front and may free float in back. They may be affixed with rivets, Velcro, or adhesive.|
*No visible rivets are allowed.
*Shoulder straps shall not have a flat end at the ends of them. They shall be ribbed 100%.
*Shoulder straps should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD).|
*These shall be affixed in the front (no snaps, rivets or brads shall be visible).
*These shall be affixed in the back (no snaps, rivets or brads shall be visible).}}

{{CRLtemplate|File:TK Commander Shoulders.jpg|Shoulder Bells|
*One on each shoulder. The shoulder bells are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders.
*The entire shoulder bell shall be blue. |
*Shoulder bells are rounded at the corners.
*No shoulder bell straps across the biceps.
*Shoulder bells/blue Commander details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD).|}}

{{CRLtemplate|File:TK Commander Biceps.jpg|Biceps|
*Biceps are fully closed.
*Two blue vertical stripes shall be present on both biceps (one to the front and one on the side).|
*No shoulder bell straps across the biceps.
*Biceps/blue Commander details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). |}}

{{CRLtemplate|File:TK Commander Forearms.jpg|Forearms|
*Forearms are fully closed.
*Two blue vertical stripes shall be present on both Forearms (one to the front and one on the side). |
*Forearms/blue Commander details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). |
*No return edge on the inside of the front of the forearm is allowed.}}

{{CRLtemplate|File:TK_anh_stunt_handplates.jpeg|Hand Plates|
*Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material.|
*Hand plates should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). |
*Hand guards shall be latex or latex-like, painted white, affixed to rubber gloves in lieu of plastic hand guards.}}

{{CRLtemplate|File:TK_anh_stunt_gloves.jpeg|Gloves|
*Black in color, made of either rubber, nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured.| |
*Gloves shall be rubber or rubber like chemical gloves in black.}}

{{CRLtemplate|File:TK_Commander_Chest.jpg|Chest|
*Chest plate overlaps the abdominal plate.
*A blue detail shall be present in the form of a Y-Shape. The blue Y-Shaped detail will have slanted white stripes, one on each side of the flared upper parts of the Y-shape.
*A white flexible U shaped gasket or molded lip shall be present around all edges. |
*Chest/blue Commander details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). |
*Fabric or elastic strip connecting chest to back shall be either black or not present.
*Ideally the AM/FX style chest plate should be replaced with a more screen accurate type. If using an AM/FX style chest plate, it shall be trimmed at the bottom and sides to eliminate the over elongated appearance and to give a more accurate look (Note: Return edge is not required but shall have the rubber gasket).
}}

{{CRLtemplate|File:TK Commander Back.jpg|Back|
*Back plate contains a "O II" design.
*A blue detail shall be present in the form of a Y-Shape. The blue Y-Shaped detail will have slanted white stripes, one on each side of the flared upper parts of the Y-shape.
*A white flexible U shaped gasket or molded lip shall be present around all edges. |
*The Back plate/blue Commander details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). |
*Back plate shall have no, or minimal overlap of the kidney plate.
*Ideally the AM/FX style back plate should be replaced with a more screen accurate type. If using an AM/FX style back plate it shall have no, or minimal overlap of the kidney plate and shall be reshaped to emulate a screen used back plate by properly trimming and re-shaping (stretching) the left and right edges of the armor to contour to your body. (Note:Return edge is not required but shall have the rubber gasket). Note: There is currently no tutorial available for this, but you can see an example of this Mod and visual comparison at whitearmor.net}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
*Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs.| | }}

{{CRLtemplate|File:TK Commander Ab.jpg|Abdomen Plate|
*Ab plate buttons shall be all black.
*Ab plate button detail shall be inverted compared to ANH/ESB.
*A blue stripe shall be present on the ab section and stops underneath the belt area. The blue stripe is wide at the bottom and narrows toward the top, to match up to the blue Y-Shaped detail of the chest plate.
*A white flexible U shaped gasket or molded lip shall be present around all edges. |
*Ab plate/blue Commander details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). |
*There shall be no split rivet or brad visible on the crotch tab of the ab plate.
*Left vertical row of ab plate buttons should contain five buttons. All buttons shall be of the same size and color and shall be visible (not covered by the belt). The fifth button shall be mounted vertically above the standard four buttons.}}

{{CRLtemplate|File:TK Commander Butt.jpg |Kidney & Butt Plate|
*A separate kidney/butt plate is not allowed - the kidney and butt plate shall be combined/fused to a single plate/one piece.
*A white flexible U shaped gasket or molded lip shall be present around all edges.
*The crotch tab of the butt plate area may or may not have visible snaps.|
*The edges of the hip area should be rounded/curved (not like the straight lines found on the ANH/ESB butt plate).
*Kidney/Butt plate should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD).|
*Two rivets shall be present on each side of the kidney plate, approximately 4mm from the inside edge of the U shaped gasket or molded lip that is adjacent to the ab plate. There will be one rivet near the top and one near the bottom on each side. They may be painted white, or not.
*There shall be no visible snaps, rivets or brads on the crotch tab of the butt plate tab. }}

{{CRLtemplate|File:TKC INC 1.jpg|Belt|
*Belt face is made of plastic (TK ammo belt).
*The soft belt proper is tightly woven nylon/cordura like/style material or material with a tightly woven nylon/cordura like/style covering. Size must be 2.25" (57mm) to 2.5" (64mm) wide. The color is to be white to off-white.
*The drop boxes shall be painted gray and dangle from the sides of the plastic front belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.|
*The belt material should be lightly aged,(battle worn), but not weathered like a Sandtrooper (TD). Leather and vinyl are not acceptable.
*There shall be two square buttons, one on each end of the plastic ammo belt. The center square button is not allowed.
*Belt face(TK ammo belt)and drop boxes should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD). |
*The corners of the plastic ammo belt shall be trimmed at a 45 degree angle.
*Drop boxes are closed in the back.
*The belt proper shall have (eight total) white rivets. Two rivets close to each side of the thermal detonator, and two rivets approximately an inch away from the edge of the ammo belt (The rivets should form a rectangular pattern). }}

{{CRLtemplate|File:TK_anh_stunt_detonator.jpeg|Thermal Detonator|
*(A.K.A. O2 canister) attaches to the center back of the belt. This is an all gray cylinder without silver stickers or silver paint. The cylinder is between 2” (50mm) and 2.68"(68mm) in diameter with white end caps on each end. The white control panel pad faces upwards, with controls/round washer style detail closest to the right end cap. The total length should be approximately 7.50" (190.5mm). The thermal detonator shall be attached via metal or metallic-appearing clips approximately 3/4" (19mm) wide |
*The thermal detonator should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD).|
*The thermal detonator control panel shall have correct ROTJ details, or the "game style" version. The ANH/ESB style is not allowed. }}

{{CRLtemplate|File:TK Commander Thighs.jpg|Thighs|
*Thigh armor shall be closed in the back.
*The ammo belt shall be installed on the bottom of the right thigh.
*The outside half of the right thigh shall be blue with two white semi-horizontal stripes near the top.|
*Thighs/blue Commander details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD).|
*The thigh ammo belt shall be connected by brads/split rivets only - standard rivets are not acceptable.
*The bottom corners of the thigh ammo belt shall be rounded off. }}

{{CRLtemplate|File:TK_Commander_Shins.jpg|Lower Legs|
*Greaves close in the back. The trapezoid knee plate (sniper knee plate) is affixed to the left greave and may have two visible brads or rivets securing it to the greave.
*The AM greaves (shins) shall be on the proper legs, with a new cover strip. The cover strip edge shall be facing the inside of the leg. Note: There is a manufacturer defect with the AM greaves (shins) that may cause you to wear the them improperly. Please see the Tutorial titled :"AM armor shins: the proper way to assemble and wear", on the whitearmor.net
*Only the outside half of the right greave shall be blue.|
*Greaves/blue Commander details should be lightly scuffed,(battle worn), but not weathered like a Sandtrooper (TD).|}}

{{CRLtemplate|File:TK Commander Boots-1.jpg|Boots|
*White leather or leather-like, above ankle height, with a flat sole with a short heel, and small U-shaped elastic sections on both sides of the ankle with no buckles or laces. Jodhpur/Chelsea-type boots or an equivalent style is acceptable. Elvis or Mariachi boots are not allowed.
*Both boots shall have two blue stripes painted, curving across the top of the foot.| |
*There shall be no seam on the front of the boot (e.g. CABoots are not allowed).
*Boots shall be lightly scuffed.}}

{{CRLtemplate|File:TK_anh_stunt_holster.jpeg|Holster|
*Holster must be omitted from this costume.|
.| }}

{{CRLaccessories}}

{{CRLtemplate|File:TK_esb_blaster1.jpeg|BlasTech E-11 (ESB style)|
*Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.|
*Folding stock (should be in the extended position).
*No ammo counter shall be present.
*D-ring mounted on the rear.
*Correct style scope.
*No power cylinders on the magazine housing.
*Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 6 T-tracks on blaster (leaving the lowest row on the magazine housing side uncovered).
*If using the Hasbro E11 toy blaster and you cover all the rows of holes, the blaster will have 7 T-tracks total. But, if you want to have the correct number of T-tracks (6 total) with the lower row of open vent holes on the magazine housing side, then you shall cover the pre-existing rows of holes with T-tracks, and grind off the lower integrated T-track on the magazine housing side and drill a new row of holes in its place.|
}}

{{CRLtemplate|File:TK_rotj_e11.jpg|BlasTech E-11 (ROTJ Style)|
*Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster. |
*Folding stock (should be in the extended position).
*No ammo counter shall be present.
*D-ring mounted on the rear.
*Correct style scope.
*No power cylinders on the magazine housing.
*Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 7 U shaped channels on blaster (all holes on barrel shall be covered).
*If using the popular commercially available Stormtrooper blasters, you shall grind off the T-tracks and replace them with U shaped channels and cover the open rows of holes (total of 7 U shaped channels in all).
*Correct greeblies on the left rear area shall be present (door catch and two "hammers").|
*Folding stock shall be in the extended position.
*Hasbro blasters are not allowed, even conversions. }}

{{CRLtemplate|File:Tk_anh_hero_se14r.jpg|BlasTech SE-14R|
*The SE-14R blaster may be carried. It shall have a correct scope if carried in lieu of the E-11 for informal events.| | }}

{{CRLtemplate|File:1XX_17.jpg‎|Lightsaber (The Force Unleashed)|
*The hilt should be Graflex style or have the characteristics of the Graflex, (reference Luke Skywalker's lightsaber from ANH and ESB). If the lightsaber has a blade, it may be one of the color blades used in the video game, The Force Unleashed. The choice of blade colors are: Black, Blue, Green, Gold, Purple, Red and Yellow.
*Note: Double blades, small Yoda style lightsaber, or inexpensive non-FX Hasbro Lightsaber toys are not allowed.| |
*The hilt shall be made to reference Starkiller's lightsaber (as seen in The Force Unleashed). If the lightsaber has a blade, it may be one of the color blades used in the video game, The Force Unleashed. The choice of blade colors are: Black, Blue, Green, Gold, Purple, Red and Yellow.}}

{{CRLfooter|FISD_CRL|T}}