Databank - User contributions [en]

Costuming:CX CW-animated ARF-Wiley

2013-05-25T15:39:46Z

BLACKSNAKE: Created page with "{{CRLheader|ARF Trooper|File:Missingprofile.jpg|none|non}} {{CRLdetinfo| 1111 |ARF Trooper Wiley|CX|The Clone Wars, seasons 4| ARF Trooper Wiley is a member of the Wolfepack und..."

{{CRLheader|ARF Trooper|File:Missingprofile.jpg|none|non}}

{{CRLdetinfo| 1111 |ARF Trooper Wiley|CX|The Clone Wars, seasons 4|
ARF Trooper Wiley is a member of the Wolfepack under the command of Commander Wolfe. He was first seen in a hangar bay operating an AT-RT. He was then loaded onto an AT-TE and brought down to the system of Aleena.}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blank.jpg|ARF Trooper Wiley Helmet|
*Clone Wars style ARF helmet required. Movie style helmets cannot be combined with animated armor.
*Helmet painted matte or satin white. If weathered, the weathering should be shades of grey.
*Snout and cheeks must be painted blue-grey.
*Smoked black lens.
*Visor painted blue-grey.
*Faceplate around visor as well as dome of helmet painted matte or satin white.
*Sides and back of helmet above lower curved tube section must be painted tan.
*A scarlet red "wolfe" emblem must be on the sides of the visor at the temples.
*Scarlet red "wolfe ears" are painted starting at the front edge of the visor and continues onto the dome of the helmet.
*Consult reference images for further details. ||}}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blank.jpg|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* A dark scarlete stripe is painted down the center of the shoulder.|
* Shoulder bells must be weathered.| }}

{{CRLtemplate|File:Blank.jpg|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*A dark scarlete stripe is painted down the outside of the upper arms in line with the stripe on the shoulders.
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blank.jpg|Forearm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
A dark scarlet stripe is painted down the outside of the armor in line with the stripe on the shoulders and upper arms.
*Left forearm must have a compad painted white that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
*Elbow plate is painted dark scarlet on the outside half and matte or satin white on the inside half. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Hand Plates|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRL-TC_animated_chest}}

{{CRL-TC_animated_back}}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRL-TC_animated_thighs}}

{{CRL-TC_animated_shins}}

{{CRL-TC_animated_boots}}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CC - Commander Fox Phase 2

2013-05-01T02:21:55Z

BLACKSNAKE:

{{CRLheader|Clone Commander Fox, Phase 2|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Commander Fox, Phase 2|CC|The Clone Wars Season 4|Commander Fox appears in the "Deception" episode of Season 4. He is the commander that accepts Hardeen into custody. While never named in the episode, it has been confirmed that it is Fox. Commander Fox appears again in The Clone Wars Season 5 episode "The Jedi Who Knew Too Much" as the head of the Republic detention facility.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.jpg|Helmet|
*Phase 2 Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Low fin with a narrow ridge along each side.
* Grey frown with 3 black teeth either side. Teeth may be cut out and backed with black mesh or painted.
* T shaped visor that extend down to the nose.
* 2 aerators in the front, Aerators are black with a grey detail in the centre.
* Each cheek tube has 6 black stripes.
* 3 dark grey raised bumps on each ear.
* Chin greeblie is painted black or dark grey.
* Helmet is painted crimson.
* Helmet fin is painted satin or matte white, if weathered it should be shades of grey.
* Centre lower jaw is painted satin or matte white, if weathered crimson paint should show underneath the white.
* There are 12 white stripes on the front of each tube, they should be evenly spaced starting at the 12 O’clock position and finishing at the 5 o’clock position for the left and 7 o’clock position for the right.
* The cheeks should be painted satin or matte white and the white should extend around the ear and to the rear recessed areas finishing at the rear raised section.
* There is an antenna behind the right ear, the base starts at the recessed area and finishes. approximately at the top of the ear cap. The antenna then extends from the base.
* Antenna should be painted dark grey or black.
* Bullet shape lamp with white lense on the left hand side of the dome sits just above the visor. Painted dark grey/black.
* A phase 2 animated visor sits on the brow and extends to the back of each ear.
* Visor should be painted dark grey or black with grey details. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.jpg|Shoulder Bells|
* Shoulders are a mirror image of each other in shape.
* Shoulders taper at the centre toward the bottom edge.
* Shoulders are painted satin or matte white, if weathered it should be shades of grey.
* The left hand shoulder has the emblem of the galactic senate painted on it in crimson. |
* Shoulder bells must be weathered.| }}

{{CRLtemplate|File:Blankwhite.jpg|Upper Arm Armor|
* Biceps are cylindrical with no detail/sculptural features.
* Biceps are painted crimson.
* Biceps have 2 white stripes around the entire bicep. The top of the upper stripe should be at approximately half way down the bicep. The bottom stripe sits approximately 1/4” off the bottom of the bicep. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.jpg|Forearm Armor|
* Armour must be painted crimson.
* Right forearm must have a compad with 8 small buttons, 1 large main button, and 1 slightly small rectangular button. The compad must be painted white, if weathered It should be shades of grey.
* Armour must be seamless on the outside edge. Due to the shape of the armour, a butted seam is acceptable on the inside if required.
* Elbow plate is integrated into the forearm and does not extend past the arm. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Hand Plates|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.jpg|Chest Armor|
* Armour must be painted crimson.
* The pecs of the chest are painted satin or matte white, if weathered it should be shades of grey.
* Lower portion of the chest has an angular notch for the abdomen armour to fit into.
* Chest and back plate must match together at the sides and shoulder with no gap.
* Each side has a butted seam line where the front and back halves come together.
*Dark scarlet shoulder straps should be placed underneath the chest to connect to the back. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Back Armor|
*Armour must be painted crimson
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel blocks and the right of the back there should be 3 parallel blocks. All detail painted in dark grey.
*Dark scarlet shoulder straps should be placed underneath the chest to connect to the back. |
*Back armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Ab Armor|
*Armour must be painted crimson.
*Top edge of the armour is angled to match the chest.
*The ab armour protrudes out in the middle to better up with the chest.
*4 inset lines divide the ab plate into segments.
*A butted seam between the ab plate and kidney is acceptable. |
*Ab armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Kidney Plate|
*Armour must be painted crimson.
*A butted seam between ab plate and kidney is acceptable.
*2 inset lines divide the kidney plate into sections. |
*Kidney armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Cod and Posterior Armor|
*Armour must be painted crimson.
*Cod and posterior armour should connect at the hips with a neat butted seam line. |
*Armour must be weathered.|}}

{{CRLtemplate|File:Blankwhite.jpg|Belt and Ammo Box's|
*Belt is approximately 3” tall and divided into 1.75” wide segments. The front segments have a key/slot detail.
*Belt boxes are mounted at the hips. Butted seam are permited at the connection if required.
*Belt and belt boxes must be painted satin or matte white.
*Detonator is centres on the back of the belt with no control buttons. The detonator has 2 lines set in approx. ½”-5/8” from the edges. Lines may be recessed or painted on.
*Detonator is painted crimson.
*The inside of the detonator end caps is painted dark grey. |
*Belt and box's must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Kama|
*The kama must be made of black leather, leather like material, or heavy canvas.
*The kama has primer grey trim.
*The front edges of the kama should line up with the outside edges of the front two panels of the belt.
*The back of the kama is split all the way up to the belt.
*The bottom edges of the kama are rounded.
*The kama should extend to the middle of the knee. | | }}

{{CRLtemplate|File:Animated Holsters.jpg|Holsters|
*Holsters must be painted satin or matte white. If weathered, it should be shades of grey
*Holsters connect to the belt via straps. Straps should be painted matte or satin white. |
*Holsters must be weathered.|}}

{{CRLtemplate|File:Blankwhite.jpg|Thigh Armor|
*Armour must be painted crimson.
*Front thigh armour should have a flat triangular area near the knee with a notch cut out for the knee armour. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Armour must be seamless. No visible traces of how the armour was assembles should be shown.
*Rear of the thigh should have an indentation. |
*Armour must be weathered. |}}

{{CRLtemplate|File:Blankwhite.jpg|Lower Leg Armor|
*Armour must be painted matte or satin white. If weathered, it should be shades of grey.
*Knee armour is intergrated with the lower leg.
*Knee armour must be painted crimson.
*The armour must have a flat centre triangle below the knee plate, with the single point facing downward.
*The calf detail of the armour has a ridge wrapping around the back of the leg.
*Back of the lower legs should have an indentation just under the calf to follow down to the ankle
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
*Armor must be weathered. |
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}

{{CRLtemplate|File:Blankwhite.jpg|Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armour. Boots must be lace-less and have flat soles.
*Boots have a cenre strip running from the toe to the ankle, a strap across the top fo the foot, and 2 flat white discs on either side of the foot, terminating the strap.
*Soles are crimson. |
*Boots must have accurate notched sole.
*Boots must be weathered. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CC - Commander Fox Phase 2

2013-05-01T02:16:53Z

BLACKSNAKE:

{{CRLheader|Clone Commander Fox, Phase 2|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Commander Fox, Phase 2|CC|The Clone Wars Season 4|Commander Fox appears in the "Deception" episode of Season 4. He is the commander that accepts Hardeen into custody. While never named in the episode, it has been confirmed that it is Fox.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.jpg|Helmet|
*Phase 2 Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Low fin with a narrow ridge along each side.
* Grey frown with 3 black teeth either side. Teeth may be cut out and backed with black mesh or painted.
* T shaped visor that extend down to the nose.
* 2 aerators in the front, Aerators are black with a grey detail in the centre.
* Each cheek tube has 6 black stripes.
* 3 dark grey raised bumps on each ear.
* Chin greeblie is painted black or dark grey.
* Helmet is painted crimson.
* Helmet fin is painted satin or matte white, if weathered it should be shades of grey.
* Centre lower jaw is painted satin or matte white, if weathered crimson paint should show underneath the white.
* There are 12 white stripes on the front of each tube, they should be evenly spaced starting at the 12 O’clock position and finishing at the 5 o’clock position for the left and 7 o’clock position for the right.
* The cheeks should be painted satin or matte white and the white should extend around the ear and to the rear recessed areas finishing at the rear raised section.
* There is an antenna behind the right ear, the base starts at the recessed area and finishes. approximately at the top of the ear cap. The antenna then extends from the base.
* Antenna should be painted dark grey or black.
* Bullet shape lamp with white lense on the left hand side of the dome sits just above the visor. Painted dark grey/black.
* A phase 2 animated visor sits on the brow and extends to the back of each ear.
* Visor should be painted dark grey or black with grey details. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.jpg|Shoulder Bells|
* Shoulders are a mirror image of each other in shape.
* Shoulders taper at the centre toward the bottom edge.
* Shoulders are painted satin or matte white, if weathered it should be shades of grey.
* The left hand shoulder has the emblem of the galactic senate painted on it in crimson. |
* Shoulder bells must be weathered.| }}

{{CRLtemplate|File:Blankwhite.jpg|Upper Arm Armor|
* Biceps are cylindrical with no detail/sculptural features.
* Biceps are painted crimson.
* Biceps have 2 white stripes around the entire bicep. The top of the upper stripe should be at approximately half way down the bicep. The bottom stripe sits approximately 1/4” off the bottom of the bicep. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.jpg|Forearm Armor|
* Armour must be painted crimson.
* Right forearm must have a compad with 8 small buttons, 1 large main button, and 1 slightly small rectangular button. The compad must be painted white, if weathered It should be shades of grey.
* Armour must be seamless on the outside edge. Due to the shape of the armour, a butted seam is acceptable on the inside if required.
* Elbow plate is integrated into the forearm and does not extend past the arm. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Hand Plates|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.jpg|Chest Armor|
* Armour must be painted crimson.
* The pecs of the chest are painted satin or matte white, if weathered it should be shades of grey.
* Lower portion of the chest has an angular notch for the abdomen armour to fit into.
* Chest and back plate must match together at the sides and shoulder with no gap.
* Each side has a butted seam line where the front and back halves come together.
*Dark scarlet shoulder straps should be placed underneath the chest to connect to the back. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Back Armor|
*Armour must be painted crimson
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel blocks and the right of the back there should be 3 parallel blocks. All detail painted in dark grey.
*Dark scarlet shoulder straps should be placed underneath the chest to connect to the back. |
*Back armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Ab Armor|
*Armour must be painted crimson.
*Top edge of the armour is angled to match the chest.
*The ab armour protrudes out in the middle to better up with the chest.
*4 inset lines divide the ab plate into segments.
*A butted seam between the ab plate and kidney is acceptable. |
*Ab armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Kidney Plate|
*Armour must be painted crimson.
*A butted seam between ab plate and kidney is acceptable.
*2 inset lines divide the kidney plate into sections. |
*Kidney armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Cod and Posterior Armor|
*Armour must be painted crimson.
*Cod and posterior armour should connect at the hips with a neat butted seam line. |
*Armour must be weathered.|}}

{{CRLtemplate|File:Blankwhite.jpg|Belt and Ammo Box's|
*Belt is approximately 3” tall and divided into 1.75” wide segments. The front segments have a key/slot detail.
*Belt boxes are mounted at the hips. Butted seam are permited at the connection if required.
*Belt and belt boxes must be painted satin or matte white.
*Detonator is centres on the back of the belt with no control buttons. The detonator has 2 lines set in approx. ½”-5/8” from the edges. Lines may be recessed or painted on.
*Detonator is painted crimson.
*The inside of the detonator end caps is painted dark grey. |
*Belt and box's must be weathered. | }}

{{CRLtemplate|File:Blankwhite.jpg|Kama|
*The kama must be made of black leather, leather like material, or heavy canvas.
*The kama has primer grey trim.
*The front edges of the kama should line up with the outside edges of the front two panels of the belt.
*The back of the kama is split all the way up to the belt.
*The bottom edges of the kama are rounded.
*The kama should extend to the middle of the knee. | | }}

{{CRLtemplate|File:Animated Holsters.jpg|Holsters|
*Holsters must be painted satin or matte white. If weathered, it should be shades of grey
*Holsters connect to the belt via straps. Straps should be painted matte or satin white. |
*Holsters must be weathered.|}}

{{CRLtemplate|File:Blankwhite.jpg|Thigh Armor|
*Armour must be painted crimson.
*Front thigh armour should have a flat triangular area near the knee with a notch cut out for the knee armour. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Armour must be seamless. No visible traces of how the armour was assembles should be shown.
*Rear of the thigh should have an indentation. |
*Armour must be weathered. |}}

{{CRLtemplate|File:Blankwhite.jpg|Lower Leg Armor|
*Armour must be painted matte or satin white. If weathered, it should be shades of grey.
*Knee armour is intergrated with the lower leg.
*Knee armour must be painted crimson.
*The armour must have a flat centre triangle below the knee plate, with the single point facing downward.
*The calf detail of the armour has a ridge wrapping around the back of the leg.
*Back of the lower legs should have an indentation just under the calf to follow down to the ankle
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
*Armor must be weathered. |
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}

{{CRLtemplate|File:Blankwhite.jpg|Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armour. Boots must be lace-less and have flat soles.
*Boots have a cenre strip running from the toe to the ankle, a strap across the top fo the foot, and 2 flat white discs on either side of the foot, terminating the strap.
*Soles are crimson. |
*Boots must have accurate notched sole.
*Boots must be weathered. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:TC - Coruscant Guard phase 1

2013-04-24T02:48:54Z

BLACKSNAKE: Created page with "{{CRLheader|Coruscant Guard, Phase 1|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}} {{CRLdetinfo| 1111 |Coruscant Guard, Phase 1|TC|The Clone Wars, seasons 1-3|The Corus..."

{{CRLheader|Coruscant Guard, Phase 1|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Coruscant Guard, Phase 1|TC|The Clone Wars, seasons 1-3|The Coruscant Guard and has appeared in both the series and the original theatrical release. They operated the Diplomatic Escort Group which was charged with protecting diplomats on key missions.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blank.jpg|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*A dark scarlet line about 1 inch wide shall be painted above the brow of the visor from left to right.
*A dark scarlet diamond shall be painted in the center of the forehead of the helmet from the brow of the visor and ends just at the start of the fin.
*A dark scarlet inverted triangle shall be painted below the visor, extending on either side of the "center" of the helmet down the sides about halfway. Consult reference images for more detail.
*The ear caps on the left and rights sides of the helmet shall be painted matte or satin white and weathered.
*A black visor extends down through the entire frown area.
*Narrow fin on dome.
*Raised bump at each ear, 1" - 1.25" in diameter.
*4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
*A grey stripe runs around back of dome.
*Raised satin white circle at the back of the helmet.
*Rectangular indent at the back of the helmet shall be black or heavily weathered grey. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blank.jpg|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* The edges of the shoulders should outlined by a dark scarlet line. The line is about 2 inches wide along the bottom of the shoulder and about 1 inch wide around the rest of the shoulder.|
* Shoulder bells must be weathered.| }}

{{CRLtemplate|File:Blank.jpg|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*On the back of the biceps, there is what appears to be a dark scarlet upsidedown "Y". Consult reference images for more details.
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blank.jpg|Forearm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Left forearm must have a compad painted white that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
*Elbow plate is painted matte or satin white. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Hand Plates|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blank.jpg|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*The Symbol of the Galactic Senate is painted in dark scarlet on the center of chest, with the center of the symbol at the top of the curved notch.
*Extending out from the Senate symbol is a dark scarlet line that moves towards the back armor and expands in size. The line sits under the breast portion of the armor. Consult reference images for more detail.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Matte or satin white shoulder straps must be placed over the chest and back armor at the seams. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Back Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*A two-inch dark scarlet stripe extends from the chest below the arm and ending just on either side of the rear tank.
*Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper.
*Matte or satin white shoulder straps should be placed over the chest and back armor at the seams. |
*Back armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Ab Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*The Ab armor shall have the bottom portion of the Galactic Senate symbol in the center extending down the abs to the belt. Consult reference images for more detail. |
Ab armor must be weathered. | }}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRLtemplate|File:Blan.gif|Belt Boxes|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*2 rectangular boxes are mounted at the hips. The top edge of the box is tapered town toward the outside. There is an inset detail near the top of each box. |
*Armor must be weathered. | }}

{{CRL-TC_animated_thighs}}

{{CRLtemplate|File:Blank.jpg|Lower Leg Armor|
*Armor must be painted matte or satin white with a dark scarlet stripe that wraps around the calf about 2" below the top of the armor and continues down the front center of the armor. Consult reference images for more detail. If weathered, the weathering should be shades of grey.
*Knee armor painted white and is integrated with the lower leg.
*Knee armor has an inverted dark scarlet triangle painted down the center.
*The armor should have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin. |
*Armor must be weathered. | }}

{{CRL-TC_animated_boots}}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|T}}

Costuming:CC CW-animated fox

2013-04-24T01:54:45Z

BLACKSNAKE:

{{CRLheader|Clone Commander Fox|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Commander Fox|CC|The Clone Wars, seasons 1-3|Fox leads the Coruscant Guard, and has appeared in both the series and the original theatrical release.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*An animated visor shall be attached to the helmet just over the lens. the visor shall be painted dark scarlet. Consult reference images for more detail.
*The top of the helmet fin, sides and rear underside shall be painted dark scarlet and weathered.
*The cheek indents of the helmet are painted dark scarlet.
*A dark scarlet inverted triangle shall be painted below the visor, extending on either side of the "center" of the helmet down the sides about halfway. Consult reference images for more detail.
*The ear caps on the left and rights sides of the helmet shall be painted matte or satin white and weathered.
*A black communications antenna shall be attached to the right side of the helmet at the ear cap.
*A white led lamp with a white lens shall be mounted to the left side of the visor.
*A black visor extends down through the entire frown area.
*Narrow fin on dome.
*Raised bump at each ear, 1" - 1.25" in diameter.
*4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
*A grey stripe runs around back of dome.
*Raised satin white circle at the back of the helmet.
*Rectangular indent at the back of the helmet shall be black or heavily weathered grey. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.|
* Shoulder bells must be weathered.| }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*On the back of the biceps, there is what looks like a dark scarlet upsidedown "Y" along with a smaller dark scarlet "swooshes" beginning at the mid-line of each bicep and swooping horizontally back & Upwards. Consult reference images for more details.
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Left forearm must have a compad painted white that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
*Elbow plate is painted matte or satin white. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*The Symbol of the Galactic Senate is painted in dark scarlet on the center of chest, with the center of the symbol at the top of the curved notch.
*Extending out from the Senate symbol is a dark scarlet line that moves towards the back armor and expands in size. The line sits under the breast portion of the armor. Consult reference images for more detail.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Dark scarlet shoulder straps must be placed over the chest and back armor at the seams. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*A two-inch dark scarlet stripe extends from the chest below the arm and ending just on either side of the rear tank.
*Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper.
*Dark scarlet shoulder straps should be placed over the chest and back armor at the seams. |
*Back armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*The Ab armor shall have the bottom portion of the Galactic Senate symbol in the center extending down the abs to the belt. Consult reference images for more detail. |
Ab armor must be weathered. | }}

{{CRL-TC_animated_kidney}}

{{CRLtemplate|File:Blankwhite.gif|Codpiece and belt front|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Belt is approx 3" tall and divided into 1.75" wide segments. The front segments have a key/slot detail.
*Belt is painted dark scarlet.
*Belt boxes are mounted at the hips. Butted seams are permitted at this connection if required.
*Cod and Posterior armor should connect at the hips. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Posterior Armor, belt rear and detonator|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Belt is approx 3" tall and divided into 1.75" wide segments.
*Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.
*Detonator is centered on the back of belt with no control buttons. The detonator has 2 lines set in approx 1/2" - 5/8" from the edges. Lines may be recessed or painted on.
*Belt and Detonator is painted dark scarlet. |
*Armor must be weathered.
*Detonator lines must be recessed.| }}

{{CRLtemplate|File:Blankwhite.gif|Belt Boxes|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*2 rectangular boxes are mounted at the hips. The top edge of the box is tapered town toward the outside. There is an inset detail near the top of each box. |
*Armor must be weathered. | }}

{{CRL-TC_animated_thighs}}

{{CRLtemplate|File:Blankwhite.gif|Kama|
*The kama must be made of black leather, leather like material, or heavy canvas.
*The kama has dark scarlet trim that should match the stripes on the armor.
*The front edges of the kama should line up with the outside edges of the front two panels of the belt.
*The back of the kama is split all the way up to the belt. | | }}

{{CRLtemplate|File:Animated Holsters.jpg|Holsters|
*Holsters must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. |
*Holsters must be weathered.|}}

{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
*Armor must be painted dark scarlet with a white stripe that wraps around the calf about 2" below the top of the armor and continues down the front center of the armor. Consult reference images for more detail. If weathered, the weathering should be shades of grey.
*Knee armor painted white and is integrated with the lower leg.
*The armor should have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Boots|
*Dark Scarlet, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
Boots have a dark scarlet center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat dark scarlet discs on either side of the foot, terminating the strap.
*Sole is white. |
* Boots must have accurate notched sole. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CC CW-animated fox

2013-04-24T01:46:31Z

BLACKSNAKE:

{{CRLheader|Clone Commander Fox|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Commander Fox|CC|The Clone Wars, seasons 1-3|Fox leads the Coruscant Guard, and has appeared in both the series and the original theatrical release.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*An animated visor shall be attached to the helmet just over the lens. the visor shall be painted dark scarlet. Consult reference images for more detail.
*The top of the helmet fin, sides and rear underside shall be painted dark scarlet and weathered.
*The cheek indents of the helmet are painted dark scarlet.
*A dark scarlet inverted triangle shall be painted below the visor, extending on either side of the "center" of the helmet down the sides about halfway. Consult reference images for more detail.
*The ear caps on the left and rights sides of the helmet shall be painted matte or satin white and weathered.
*A black communications antenna shall be attached to the right side of the helmet at the ear cap.
*A white led lamp with a white lens shall be mounted to the left side of the visor.
*A black visor extends down through the entire frown area.
*Narrow fin on dome.
*Raised bump at each ear, 1" - 1.25" in diameter.
*4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
*A grey stripe runs around back of dome.
*Raised satin white circle at the back of the helmet.
*Rectangular indent at the back of the helmet shall be black or heavily weathered grey. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.|
* Shoulder bells must be weathered.| }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*On the back of the biceps, there is what looks like a dark scarlet upsidedown "Y" along with a smaller dark scarlet "swooshes" beginning at the mid-line of each bicep and swooping horizontally back & Upwards. Consult reference images for more details.
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Left forearm must have a compad painted white that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
*Elbow plate is painted matte or satin white. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*The Symbol of the Galactic Senate is painted in dark scarlet on the center of chest, with the center of the symbol at the top of the curved notch.
*Extending out from the Senate symbol is a dark scarlet line that moves towards the back armor and expands in size. The line sits under the breast portion of the armor. Consult reference images for more detail.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Dark scarlet shoulder straps must be placed over the chest and back armor at the seams. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*A two-inch dark scarlet stripe extends from the chest below the arm and ending just on either side of the rear tank.
*Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper.
*Dark scarlet shoulder straps should be placed over the chest and back armor at the seams. |
*Back armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*The Ab armor shall have the bottom portion of the Galactic Senate symbol in the center extending down the abs to the belt. Consult reference images for more detail. |
Ab armor must be weathered. | }}

{{CRL-TC_animated_kidney}}

{{CRLtemplate|File:Blankwhite.gif|Codpiece and belt front|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Belt is approx 3" tall and divided into 1.75" wide segments. The front segments have a key/slot detail.
*Belt is painted dark scarlet.
*Belt boxes are mounted at the hips. Butted seams are permitted at this connection if required.
*Cod and Posterior armor should connect at the hips.
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Posterior Armor, belt rear and detonator|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Belt is approx 3" tall and divided into 1.75" wide segments.
*Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.
*Detonator is centered on the back of belt with no control buttons. The detonator has 2 lines set in approx 1/2" - 5/8" from the edges. Lines may be recessed or painted on.
*Belt and Detonator is painted dark scarlet. |
*Armor must be weathered.
*Detonator lines must be recessed.| }}

{{CRLtemplate|File:Blankwhite.gif|Belt Boxes|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*2 rectangular boxes are mounted at the hips. The top edge of the box is tapered town toward the outside. There is an inset detail near the top of each box. |
*Armor must be weathered. | }}

{{CRL-TC_animated_thighs}}

{{CRLtemplate|File:Blankwhite.gif|Kama|
*The kama must be made of black leather, leather like material, or heavy canvas.
*The kama has dark scarlet trim that should match the stripes on the armor.
*The front edges of the kama should line up with the outside edges of the front two panels of the belt.
*The back of the kama is split all the way up to the belt. | | }}

{{CRLtemplate|File:Animated Holsters.jpg|Holsters|
*Holsters must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. |
*Holsters must be weathered.|}}

{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
*Armor must be painted dark scarlet with a white stripe that wraps around the calf about 2" below the top of the armor and continues down the front center of the armor. Consult reference images for more detail. If weathered, the weathering should be shades of grey.
*Knee armor painted white and is integrated with the lower leg.
*The armor should have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Boots|
*Dark Scarlet, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
Boots have a dark scarlet center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat dark scarlet discs on either side of the foot, terminating the strap.
*Sole is white. |
* Boots must have accurate notched sole. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CC CW-animated fox

2013-04-11T00:49:25Z

BLACKSNAKE:

{{CRLheader|Clone Commander Fox|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Commander Fox|CC|The Clone Wars, seasons 1-3|Fox leads the Coruscant Guard, and has appeared in both the series and the original theatrical release.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*An animated visor shall be attached to the helmet just over the lens. the visor shall be painted dark scarlet. Consult reference images for more detail.
*The top of the helmet fin, sides and rear underside shall be painted dark scarlet and weathered.
*The cheek indents of the helmet are painted dark scarlet.
*A dark scarlet inverted triangle shall be painted below the visor, extending on either side of the "center" of the helmet down the sides about halfway. Consult reference images for more detail.
*The ear caps on the left and rights sides of the helmet shall be painted matte or satin white and weathered.
*A black communications antenna shall be attached to the right side of the helmet at the ear cap.
*A white led lamp with a white lens shall be mounted to the left side of the visor.
*A black visor extends down through the entire frown area.
*Narrow fin on dome.
*Raised bump at each ear, 1" - 1.25" in diameter.
*4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
*A grey stripe runs around back of dome.
*Raised satin white circle at the back of the helmet.
*Rectangular indent at the back of the helmet shall be black or heavily weathered grey. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.|
* Shoulder bells must be weathered.| }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*On the back of the biceps, there is what looks like a dark scarlet upsidedown "Y" along with a smaller dark scarlet "swooshes" beginning at the mid-line of each bicep and swooping horizontally back & Upwards. Consult reference images for more details.
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Left forearm must have a compad painted white that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
*Elbow plate is painted matte or satin white. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*The Symbol of the Galactic Senate is painted in dark scarlet on the center of chest, with the center of the symbol at the top of the curved notch.
*Extending out from the Senate symbol is a dark scarlet line that moves towards the back armor and expands in size. The line sits under the breast portion of the armor. Consult reference images for more detail.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Dark scarlet shoulder straps must be placed over the chest and back armor at the seams. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*A two-inch dark scarlet stripe extends from the chest below the arm and ending just on either side of the rear tank.
*Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper.
*Dark scarlet shoulder straps should be placed over the chest and back armor at the seams. |
*Back armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*The Ab armor shall have the bottom portion of the Galactic Senate symbol in the center extending down the abs to the belt. Consult reference images for more detail. |
Ab armor must be weathered. | }}

{{CRL-TC_animated_kidney}}

{{CRLtemplate|File:Blankwhite.gif|Cod Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Cod armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Butt Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Butt armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Belt and Ammo Box's|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Belt must have two satin white belt box's one on each side the left and right of the belt mirrored images of each other.
*The Thermal detonator shall be painted dark scarlet. |
*Belt and box's must be weathered. | }}

{{CRL-TC_animated_thighs}}

{{CRLtemplate|File:Blankwhite.gif|Kama|
*The kama must be made of black leather, leather like material, or heavy canvas.
*The kama has dark scarlet trim that should match the stripes on the armor.
*The front edges of the kama should line up with the outside edges of the front two panels of the belt.
*The back of the kama is split all the way up to the belt. | | }}

{{CRLtemplate|File:Animated Holsters.jpg|Holsters|
*Holsters must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. |
*Holsters must be weathered.|}}

{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
*Armor must be painted dark scarlet with a white stripe that wraps around the calf about 2" below the top of the armor and continues down the front center of the armor. Consult reference images for more detail. If weathered, the weathering should be shades of grey.
*Knee armor painted white and is integrated with the lower leg.
*The armor should have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Boots|
*Dark Scarlet, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
Boots have a dark scarlet center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat dark scarlet discs on either side of the foot, terminating the strap.
*Sole is white. |
* Boots must have accurate notched sole. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CC CW-animated fox

2013-04-11T00:44:37Z

BLACKSNAKE:

{{CRLheader|Clone Commander Fox|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Commander Fox|CC|The Clone Wars, seasons 1-3|Fox leads the Coruscant Guard, and has appeared in both the series and the original theatrical release.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*An animated visor shall be attached to the helmet just over the lens. the visor shall be painted dark scarlet. Consult reference images for more detail.
*The top of the helmet fin, sides and rear underside shall be painted dark scarlet and weathered.
*The cheek indents of the helmet are painted dark scarlet.
*A dark scarlet inverted triangle shall be painted below the visor, extending on either side of the "center" of the helmet down the sides about halfway. Consult reference images for more detail.
*The ear caps on the left and rights sides of the helmet shall be painted matte or satin white and weathered.
*A black communications antenna shall be attached to the right side of the helmet at the ear cap.
*A white led lamp with a white lens shall be mounted to the left side of the visor.
*A black visor extends down through the entire frown area.
*Narrow fin on dome.
*Raised bump at each ear, 1" - 1.25" in diameter.
*4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
*A grey stripe runs around back of dome.
*Raised satin white circle at the back of the helmet.
*Rectangular indent at the back of the helmet shall be black or heavily weathered grey. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
* Right shoulder bell painted matte blue-gray with wolfs head motif as shown.|
* Shoulder bells must be weathered.| }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*On the back of the biceps, there is what appears to be a dark scarlet upsidedown "Y" along with a smaller dark scarlet "swooshes" beginning at the mid-line of each bicep and swooping horizontally back & Upwards. Consult reference images for more details.
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Left forearm must have a compad painted white that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
*Elbow plate is painted matte or satin white. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*The Symbol of the Galactic Senate is painted in dark scarlet on the center of chest, with the center of the symbol at the top of the curved notch.
*Extending out from the Senate symbol is a dark scarlet line that moves towards the back armor and expands in size. The line sits under the breast portion of the armor. Consult reference images for more detail.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Dark scarlet shoulder straps must be placed over the chest and back armor at the seams. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*A two-inch dark scarlet stripe extends from the chest below the arm and ending just on either side of the rear tank.
*Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper.
*Dark scarlet shoulder straps should be placed over the chest and back armor at the seams. |
*Back armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*The Ab armor shall have the bottom portion of the Galactic Senate symbol in the center extending down the abs to the belt. Consult reference images for more detail. |
Ab armor must be weathered. | }}

{{CRL-TC_animated_kidney}}

{{CRLtemplate|File:Blankwhite.gif|Cod Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Cod armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Butt Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Butt armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Belt and Ammo Box's|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Belt must have two satin white belt box's one on each side the left and right of the belt mirrored images of each other.
*The Thermal detonator shall be painted dark scarlet. |
*Belt and box's must be weathered. | }}

{{CRL-TC_animated_thighs}}

{{CRLtemplate|File:Blankwhite.gif|Kama|
*The kama must be made of black leather, leather like material, or heavy canvas.
*The kama has dark scarlet trim that should match the stripes on the armor.
*The front edges of the kama should line up with the outside edges of the front two panels of the belt.
*The back of the kama is split all the way up to the belt. | | }}

{{CRLtemplate|File:Animated Holsters.jpg|Holsters|
*Holsters must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. |
*Holsters must be weathered.|}}

{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
*Armor must be painted dark scarlet with a white stripe that wraps around the calf about 2" below the top of the armor and continues down the front center of the armor. Consult reference images for more detail. If weathered, the weathering should be shades of grey.
*Knee armor painted white and is integrated with the lower leg.
*The armor should have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Boots|
*Dark Scarlet, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
Boots have a dark scarlet center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat dark scarlet discs on either side of the foot, terminating the strap.
*Sole is white. |
* Boots must have accurate notched sole. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CC CW-animated fox

2013-04-11T00:39:04Z

BLACKSNAKE: Initial Creation

{{CRLheader|Clone Commander Fox|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Commander Fox|CC|The Clone Wars, seasons 1-3|Fox leads the Coruscant Guard, and has appeared in both the series and the original theatrical release.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blank.jpg|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*An animated visor shall be attached to the helmet just over the lens. the visor shall be painted dark scarlet. Consult reference images for more detail.
*The top of the helmet fin, sides and rear underside shall be painted dark scarlet and weathered.
*The cheek indents of the helmet are painted dark scarlet.
*A dark scarlet inverted triangle shall be painted below the visor, extending on either side of the "center" of the helmet down the sides about halfway. Consult reference images for more detail.
*The ear caps on the left and rights sides of the helmet shall be painted matte or satin white and weathered.
*A black communications antenna shall be attached to the right side of the helmet at the ear cap.
*A white led lamp with a white lens shall be mounted to the left side of the visor.
*A black visor extends down through the entire frown area.
*Narrow fin on dome.
*Raised bump at each ear, 1" - 1.25" in diameter.
*4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
*A grey stripe runs around back of dome.
*Raised satin white circle at the back of the helmet.
*Rectangular indent at the back of the helmet shall be black or heavily weathered grey. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blank.jpg|Shoulder Bells|
* Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
* Right shoulder bell painted matte blue-gray with wolfs head motif as shown.|
* Shoulder bells must be weathered.| }}

{{CRLtemplate|File:Blank.jpg|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*On the back of the biceps, there is what appears to be a dark scarlet upsidedown "Y" along with a smaller dark scarlet "swooshes" beginning at the mid-line of each bicep and swooping horizontally back & Upwards. Consult reference images for more details.
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blank.jpg|Forearm Armor|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Left forearm must have a compad painted white that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
*Elbow plate is painted matte or satin white. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Hand Plates|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blank.jpg|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*The Symbol of the Galactic Senate is painted in dark scarlet on the center of chest, with the center of the symbol at the top of the curved notch.
*Extending out from the Senate symbol is a dark scarlet line that moves towards the back armor and expands in size. The line sits under the breast portion of the armor. Consult reference images for more detail.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Dark scarlet shoulder straps must be placed over the chest and back armor at the seams. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Back Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*A two-inch dark scarlet stripe extends from the chest below the arm and ending just on either side of the rear tank.
*Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper.
*Dark scarlet shoulder straps should be placed over the chest and back armor at the seams. |
*Back armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Ab Armor|
*Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
*The Ab armor shall have the bottom portion of the Galactic Senate symbol in the center extending down the abs to the belt. Consult reference images for more detail. |
Ab armor must be weathered. | }}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRLtemplate|File:Blank.jpg|Belt and Ammo Box's|
*Armor must be painted dark scarlet. If weathered, the weathering should be shades of grey.
*Belt must have two satin white belt box's one on each side the left and right of the belt mirrored images of each other.
*The Thermal detonator shall be painted dark scarlet. |
*Belt and box's must be weathered. | }}

{{CRL-TC_animated_thighs}}

{{CRLtemplate|File:Blank.jpg|Kama|
*The kama must be made of black leather, leather like material, or heavy canvas.
*The kama has dark scarlet trim that should match the stripes on the armor.
*The front edges of the kama should line up with the outside edges of the front two panels of the belt.
*The back of the kama is split all the way up to the belt. | | }}

{{CRLtemplate|File:Animated Holsters.jpg|Holsters|
*Holsters must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. |
*Holsters must be weathered.|}}

{{CRLtemplate|File:Blank.jpg|Lower Leg Armor|
*Armor must be painted dark scarlet with a white stripe that wraps around the calf about 2" below the top of the armor and continues down the front center of the armor. Consult reference images for more detail. If weathered, the weathering should be shades of grey.
*Knee armor painted white and is integrated with the lower leg.
*The armor should have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blank.jpg|Boots|
*Dark Scarlet, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
Boots have a dark scarlet center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat dark scarlet discs on either side of the foot, terminating the strap.
*Sole is white. |
* Boots must have accurate notched sole. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:TC CW-animated boost

2013-03-22T18:18:16Z

BLACKSNAKE:

{{CRLheader|Clone Trooper Boost|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Trooper Boost|TC|The Clone Wars, seasons 1 and 2|
Boost served as a member of commander Wolffe's famed wolfpack. }}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* A black wolfpack logo starts above the lens and runs down the sides of the fin while the top of the fin and sides remain white.
* A dark scarlet 2" band curves up and out above the lens wrapping around each side making a T shape in the back and squares off above the bottom of the helmet. Consult reference images for more detail.
* Dark scarlet stripes run down the sides of the chin below the frown to the neck. These stripes start just below the frown with a curved top. Consult reference images for more detail.
* Black visor extends down through the entire frown area.
* Narrow fin on dome.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Dark scarlet stripe runs around back of dome.
* Raised dark scarlet circle at the back of the helmet.
* Rectangular indent at the back of the helmet may be dark scarlet or heavily weathered black.|
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Right shoulder armor must be dark scarlet and look to be weathered.
* Left shoulder armor must dark scarlet and have a star burst design starting as a diamond at the bottom and moving in an outward motion toward the top of the shoulder bell and look to be weathered. Consult reference images for more detail.
* Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
* Shoulder bells must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Armor must have a dark scarlet down the center that lines up with the shoulder.
* Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Upper arm armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
* Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
* Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
* Elbow plate is painted dark scarlet on the top tip that fits into the top tip of the bicep and is mirrored downward on the forearm. Consult reference images for more detail. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Forearm armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Chest armor is painted dark scarlet on the top in an arch with a 2" white gap in the center at the neck. Consult reference images for more detail. The dark scarlet color continues over the shoulders to the back and squares off covering only the detail plate and its sides. Consult reference images for more detail.
* Chest armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Back armor is dark scarlet on the the detail plate and its sides only and continues over the shoulders to the front of the chest. Consult reference images for more detail.
* Back armor must be weathered. | }}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRL-TC_animated_thighs}}

{{CRLtemplate|File:Blankwhite.gif|Shin Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Shin armor is dark scarlet on the lower front and back sides. starting in an arch where the knee plate seems to attach to the shin on the front and extends diagonally down to ward the back covering the lower half of the shins.
* Shin armor must be weathered. | }}

{{CRL-TC_animated_boots}}
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Boots must be weathered. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|T}}

Costuming:TC CW-animated sinker

2013-03-22T18:17:38Z

BLACKSNAKE:

{{CRLheader|Clone Trooper Sgt. Sinker|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Trooper Sgt. Sinker|TC|The Clone Wars, seasons 1-3|
Sinker first appears in Season 1, Episode 2 "Rise of Malevolence" as part of Commander Wolffe's unit. }}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* A black wolfpack logo starts above the lens and runs down the sides of the fin while the top of the fin and sides remain white.
* A dark scarlet 2" band curves up and out above the lens wrapping around each side making a T shape in the back and squares off above the bottom of the helmet. Consult reference images for more detail.
* Dark scarlet stripes run down the sides of the chin below the frown to the neck. These stripes start just below the frown with a curved top. Consult reference images for more detail.
* Black visor extends down through the entire frown area.
* Narrow fin on dome.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Dark scarlet stripe runs around back of dome.
* Raised dark scarlet circle at the back of the helmet.
* Rectangular indent at the back of the helmet may be dark scarlet or heavily weathered black.|
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Right shoulder armor must be dark scarlet and look to be weathered.
* Left shoulder armor must dark scarlet and have a star burst design starting as a diamond at the bottom and moving in an outward motion toward the top of the shoulder bell and look to be weathered. Consult reference images for more detail.
* Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
* Shoulder bells must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Armor must have a dark scarlet down the center that lines up with the shoulder.
* Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Upper arm armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
* Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
* Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
* Elbow plate is painted dark scarlet on the top tip that fits into the top tip of the bicep and is mirrored downward on the forearm. Consult reference images for more detail. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Forearm armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Chest armor is painted dark scarlet on the top in an arch with a 2" white gap in the center at the neck. Consult reference images for more detail. The dark scarlet color continues over the shoulders to the back and squares off covering only the detail plate and its sides. Consult reference images for more detail.
* Chest armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Back armor is dark scarlet on the the detail plate and its sides only and continues over the shoulders to the front of the chest. Consult reference images for more detail.
* Back armor must be weathered. | }}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRL-TC_animated_thighs}}

{{CRLtemplate|File:Blankwhite.gif|Shin Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Shin armor is dark scarlet on the lower front and back sides. starting in an arch where the knee plate seems to attach to the shin on the front and extends diagonally down to ward the back covering the lower half of the shins.
* Shin armor must be weathered. | }}

{{CRL-TC_animated_boots}}
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Boots must be weathered. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|T}}

Costuming:TC CW-animated sinker

2013-03-22T18:12:29Z

BLACKSNAKE:

{{CRLheader|Clone Trooper Sgt. Sinker|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Trooper Sgt. Sinker|TC|The Clone Wars, seasons 1-3|
Sinker first appears in Season 1, Episode 2 "Rise of Malevolence" as part of Commander Wolffe's unit. }}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* A black wolfpack logo starts above the lens and runs down the sides of the fin while the top of the fin and sides remain white.
* A dark scarlet 2" band curves up and out above the lens wrapping around each side making a T shape in the back and squares off above the bottom of the helmet. Consult reference images for more detail.
* Dark scarlet stripes run down the sides of the chin below the frown to the neck. These stripes start just below the frown with a curved top. Consult reference images for more detail.
* Black visor extends down through the entire frown area.
* Narrow fin on dome.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Dark scarlet stripe runs around back of dome.
* Raised dark scarlet circle at the back of the helmet.
* Rectangular indent at the back of the helmet may be dark scarlet or heavily weathered black.|
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Right shoulder armor must be dark scarlet and look to be weathered.
* Left shoulder armor must dark scarlet and have a star burst design starting as a diamond at the bottom and moving in an outward motion toward the top of the shoulder bell and look to be weathered. Consult reference images for more detail.
* Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
* Shoulder bells must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Armor must have a dark scarlet down the center that lines up with the shoulder.
* Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Upper arm armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
* Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
* Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
* Elbow plate is painted dark scarlet on the top tip that fits into the top tip of the bicep and is mirrored downward on the forearm. Consult reference images for more detail. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Forearm armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Chest armor is painted dark scarlet on the top in an arch with a 2" white gap in the center at the neck. Consult reference images for more detail. The dark scarlet color continues over the shoulders to the back and squares off covering only the detail plate and its sides. Consult reference images for more detail.
* Chest armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Back armor is dark scarlet on the the detail plate and its sides only and continues over the shoulders to the front of the chest. Consult reference images for more detail.
* Back armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Ab armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Kidney Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Kidney armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Cod Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Cod armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Butt Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Butt armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Belt and Ammo Box's|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Belt must have two belt box's one on each side the left and right of the belt mirrored images of each other.
* belt and box's must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Thigh Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Thigh armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Shin Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Shin armor is dark scarlet on the lower front and back sides. starting in an arch where the knee plate seems to attach to the shin on the front and extends diagonally down to ward the back covering the lower half of the shins.
* Shin armor must be weathered. | }}

{{CRL-TC_animated_boots}}
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Boots must be weathered. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|T}}

Costuming:TC CW-animated boost

2013-03-22T18:12:25Z

BLACKSNAKE:

{{CRLheader|Clone Trooper Boost|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Trooper Boost|TC|The Clone Wars, seasons 1 and 2|
Boost served as a member of commander Wolffe's famed wolfpack. }}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* A black wolfpack logo starts above the lens and runs down the sides of the fin while the top of the fin and sides remain white.
* A dark scarlet 2" band curves up and out above the lens wrapping around each side making a T shape in the back and squares off above the bottom of the helmet. Consult reference images for more detail.
* Dark scarlet stripes run down the sides of the chin below the frown to the neck. These stripes start just below the frown with a curved top. Consult reference images for more detail.
* Black visor extends down through the entire frown area.
* Narrow fin on dome.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Dark scarlet stripe runs around back of dome.
* Raised dark scarlet circle at the back of the helmet.
* Rectangular indent at the back of the helmet may be dark scarlet or heavily weathered black.|
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Right shoulder armor must be dark scarlet and look to be weathered.
* Left shoulder armor must dark scarlet and have a star burst design starting as a diamond at the bottom and moving in an outward motion toward the top of the shoulder bell and look to be weathered. Consult reference images for more detail.
* Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
* Shoulder bells must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Armor must have a dark scarlet down the center that lines up with the shoulder.
* Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Upper arm armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
* Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
* Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
* Elbow plate is painted dark scarlet on the top tip that fits into the top tip of the bicep and is mirrored downward on the forearm. Consult reference images for more detail. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Forearm armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Chest armor is painted dark scarlet on the top in an arch with a 2" white gap in the center at the neck. Consult reference images for more detail. The dark scarlet color continues over the shoulders to the back and squares off covering only the detail plate and its sides. Consult reference images for more detail.
* Chest armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Back armor is dark scarlet on the the detail plate and its sides only and continues over the shoulders to the front of the chest. Consult reference images for more detail.
* Back armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Ab armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Kidney Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Kidney armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Cod Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Cod armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Butt Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Butt armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Belt and Ammo Box's|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Belt must have two belt box's one on each side the left and right of the belt mirrored images of each other.
* belt and box's must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Thigh Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Thigh armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Shin Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Shin armor is dark scarlet on the lower front and back sides. starting in an arch where the knee plate seems to attach to the shin on the front and extends diagonally down to ward the back covering the lower half of the shins.
* Shin armor must be weathered. | }}

{{CRL-TC_animated_boots}}
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Boots must be weathered. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|T}}

Costuming:CX CW-animated ARF-boomer

2013-03-14T02:15:10Z

BLACKSNAKE:

{{CRLheader|ARF Trooper - Sgt. Boomer|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |ARF Trooper - Sgt. Boomer|CX|The Clone Wars: Republic Heroes (video game) |
Sgt. Boomer appears in the Republic Heroes video game, serving in the 501st under Captain Rex.}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif| ARF Trooper Helmet|
*Clone Wars style ARF helmet required. Movie style helmets cannot be combined with animated armor.
*Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Helmet should have a 1” stripe on the nose then gradually expand to 2” down the length of the helmet. Consult reference images for more detail.
*Accents on base of helmet are painted blue while the “cheeks” are painted grey. Consult reference images for more detail.
*Smoked black lens.
*An animated visor shall be attached to the helmet just over the lens and surround the entire helmet just below the dome. The visor must be painted blue with white accents. Consult reference images for more detail. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Shoulder Bells have different painting patterns. The wearer’s left shoulder should be completely blue. The right shoulder should be white with a 2” blue stripe down the middle. Consult reference images for more detail.
*Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Upper Arm Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Upper Arm Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*The elbows should be painted blue. There should also be a 1.5” blue stripe below the ridge of the forearm. This wraps around the front of the forearm to the back where it is left white mimicking the elbow lines. Consult reference images for more detail.
*Left forearm must have a Compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Forearm Armor and Compad must be painted white to match the armor. Consult reference images for more detail.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
*Armor must be seamless on the outside of the arm. No visible traces of how the armor was assembled should be shown.
*The inside of the arm can either be seamless or connected with Velcro. |
*Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:TC_animated_chest.jpg|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Chest Armor must have a blue painted ring extending from each shoulder strap to the middle of the chest. From there it extends down to the bottom of the breast plate. Consult reference images for more detail.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Shoulder straps must be placed over the chest and back armor at the seams and painted white. |
*Armor must be weathered. | }}

{{CRL-TC_animated_back}}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRLtemplate|File:TC_animated_chest.jpg|Thigh Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Thigh Armor has a blue stripe extending from the top of the thigh to about the middle that wraps completely around the thigh. Consult reference images for more detail.
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered.| }}

{{CRLtemplate|File:TC_animated_chest.jpg|Lower Leg Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Knee armor is integrated with the lower leg.
*Knees are painted blue. Consult reference images for more detail.
*The armor should have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin and should be connected with Velcro. |
*Armor must be weathered. | }}

{{CRL-TC_animated_boots}}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CX CW-animated ARF-boomer

2013-03-14T01:23:37Z

BLACKSNAKE:

{{CRLheader|ARF Trooper - Sgt. Boomer|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |ARF Trooper - Sgt. Boomer|CX|The Clone Wars: Republic Heroes (video game) |
Sgt. Boomer appears in the Republic Heroes video game, serving in the 501st under Captain Rex.}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif| ARF Trooper Helmet|
*Clone Wars style ARF helmet required. Movie style helmets cannot be combined with animated armor.
*Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Helmet should have a 1” stripe on the nose then gradually expand to 2” down the length of the helmet. Consult reference images for more detail.
*Accents on base of helmet are painted blue while the “cheeks” are painted grey. Consult reference images for more detail.
*Smoked black lens.
*An animated visor shall be attached to the helmet just over the lens and surround the entire helmet just below the dome. The visor must be painted blue with white accents. Consult reference images for more detail. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Shoulder Bells have different painting patterns. The wearer’s left shoulder should be completely blue. The right shoulder should be white with a 2” blue stripe down the middle. Consult reference images for more detail.
*Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Upper Arm Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Upper Arm Armor must be seamless. No visible traces of how the armor was assembled should be shown.|
*Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*The elbows should be painted blue. There should also be a 1.5” blue stripe below the ridge of the forearm. This wraps around the front of the forearm to the back where it is left white mimicking the elbow lines. Consult reference images for more detail.
*Left forearm must have a Compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Forearm Armor and Compad must be painted white to match the armor. Consult reference images for more detail.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
*Armor must be seamless on the outside of the arm. No visible traces of how the armor was assembled should be shown.
*The inside of the arm can either be seamless or connected with Velcro.|
*Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:TC_animated_chest.jpg|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Chest Armor must have a blue painted ring extending from each shoulder strap to the middle of the chest. From there it extends down to the bottom of the breast plate. Consult reference images for more detail.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Shoulder straps must be placed over the chest and back armor at the seams and painted white. |
*Armor must be weathered. | }}

{{CRL-TC_animated_back}}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRLtemplate|File:TC_animated_chest.jpg|Thigh Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Thigh Armor has a blue stripe extending from the top of the thigh to about the middle that wraps completely around the thigh. Consult reference images for more detail.
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered.|}}

{{CRLtemplate|File:TC_animated_chest.jpg|Lower Leg Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Knee armor is integrated with the lower leg.
*Knees are painted blue. Consult reference images for more detail.
*The armor should have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin and should be connected with Velcro.|
*Armor must be weathered. |}}

{{CRL-TC_animated_boots}}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CX CW-animated ARF-boomer

2013-03-14T01:15:51Z

BLACKSNAKE:

{{CRLheader|ARF Trooper - Sgt. Boomer|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |ARF Trooper - Sgt. Boomer|CX|The Clone Wars: Republic Heroes (video game) |
Sgt. Boomer appears in the Republic Heroes video game, serving in the 501st under Captain Rex.}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif| ARF Trooper Helmet|
*Clone Wars style ARF helmet required. Movie style helmets cannot be combined with animated armor.
*Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Helmet should have a 1” stripe on the nose then gradually expand to 2” down the length of the helmet. Consult reference images for more detail.
*Accents on base of helmet are painted blue while the “cheeks” are painted grey. Consult reference images for more detail.
*Smoked black lens.
*An animated visor shall be attached to the helmet just over the lens and surround the entire helmet just below the dome. The visor must be painted blue with white accents. Consult reference images for more detail. |
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Shoulder Bells have different painting patterns. The wearer’s left shoulder should be completely blue. The right shoulder should be white with a 2” blue stripe down the middle. Consult reference images for more detail.
*Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Upper Arm Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Upper Arm Armor must be seamless. No visible traces of how the armor was assembled should be shown.|
*Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
• Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
• The elbows should be painted blue. There should also be a 1.5” blue stripe below the ridge of the forearm. This wraps around the front of the forearm to the back where it is left white mimicking the elbow lines. Consult reference images for more detail.
• Left forearm must have a Compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
• Forearm Armor and Compad must be painted white to match the armor. Consult reference images for more detail.
• Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
• Armor must be seamless on the outside of the arm. No visible traces of how the armor was assembled should be shown.
• The inside of the arm can either be seamless or connected with Velcro.|
*Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:TC_animated_chest.jpg|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Chest Armor must have a blue painted ring extending from each shoulder strap to the middle of the chest. From there it extends down to the bottom of the breast plate. Consult reference images for more detail.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Shoulder straps must be placed over the chest and back armor at the seams and painted white. |
*Armor must be weathered. | }}

{{CRL-TC_animated_back}}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRLtemplate|File:TC_animated_chest.jpg|Thigh Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Thigh Armor has a blue stripe extending from the top of the thigh to about the middle that wraps completely around the thigh. Consult reference images for more detail.
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered.|}}

{{CRLtemplate|File:TC_animated_chest.jpg|Lower Leg Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Knee armor is integrated with the lower leg.
*Knees are painted blue. Consult reference images for more detail.
*The armor should have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin and should be connected with Velcro.|
*Armor must be weathered. |}

{{CRL-TC_animated_boots}}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CC - Commander Appo

2013-03-13T01:25:49Z

BLACKSNAKE:

{{CRLheader|Clone Commander Appo (Comic Version)|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Commander Appo (Comic Version)|CC|Episode III: Revenge of the Sith (EU sources)|
CC-1119, also known as Appo, was a clone commander who led the 501st Legion in a Republic attack on the Jedi Temple at the end of the Clone Wars. During the war, CC-1119 received training from the ARC trooper Alpha-17, where he was given the name "Appo." He served under Darth Vader during the Temple attack and later, when the Republic transformed into the Galactic Empire. Appo and his soldiers became some of the first Imperial stormtroopers, and alongside Vader he worked to suppress threats against the Empire.

From a 501st perspective, Appo is considered a standard 501st clone with the addition of the pauldron and ammo bandolier.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:501-Appo helmet copy.jpg|Helmet|

*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Visor - Black Visor.
*Helmet mohawk on dome.
*Starting on the nose of the helmet, there is a blue stripe about 1 inch wide going from the vents to the vocoder. From the middle of the two centermost vents to half an inch off the center eye curves, the area in between should be painted pale blue. Continuing from there, widening out to 3 inches from center of the mowhawk, the pale blue stripe continues. It then thins to 4 inches in the rear of the helmet squared off in the back, ¼ inch above the grey helmet wrap.
*Vertical stripes on each side of helmet cheeks that are dark blue in color.
*Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
*Primer grey stripe around back of dome.
*Ear caps are painted a dark grey.
*Helmet has the appearance of a neck ring.
*Helmet may have an optional enclosed complete neck ring that seals the helmet to the neck.|
*No additional requirements.|
*Helmet must have a full neck ring.}}

{{CRL-realistic-clone-neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:501st clone shoulder bells2.jpg |Shoulder Bells|
*Armor should be painted blue.
*Shoulders should be tear drop in shape with all rounded edges. | |
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}

{{CRLtemplate|File:Clone bicept copy.jpg|Upper Arm Armor|
*Armor should be painted matte or satin white.
*Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.||
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|‎File:Clone elbow copy.jpg|Elbow Armor|
*Armor should be painted matte or satin white.
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}

{{CRLtemplate| |Forearm Armor|
*Armor should be painted matte or satin white.
*Both left and right forearms should be mirror images of each other.
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
*The wrist of the forearm must have a blue stripe that wraps around the entire circumference of the forearm | |
*Compad has detail antenna on its left.
*Instead of a hard edge the top of the forearm has a bone ridge.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|File:Clone hand guards copy.jpg|Hand Plates|
*Armor should be painted matte or satin white.
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate||Command Pauldron|
*Pauldron should be Episode III style.
*The mantle over the left shoulder should be colored to match the detail color of the armor. (i.e. Blue)
*Right shoulder mantle and paneling on the remainder of the pauldron shall be all black.
*On the right side of the Pauldron, a ammo belt is strung down to the belt.
| | }}

{{CRLtemplate||Chest Ammo Belt|
*3 ammo boxes are attached to a black strap on right side of chest.
*2 of the boxes are blue and one is black
*All of the boxes should have a black detail in the middle of each.
| | }}

{{CRLtemplate|File:501st clone chest plate2.jpg|Chest Armor|
*Armor should be painted matte or satin white.
*Two detail slots on right breast.
*Chest armor must have a blue stripe that begins at the center of the neck and extends down the chest plate to the bottom of the breast plate. From there it extends out towards the sides. Consult reference images for more detail.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. ||
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}

{{CRLtemplate|File:501st clone back plate 2.jpg|Back Armor|
*Armor should be painted matte or satin white.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Rear tank detailed area is painted blue.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. ||
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:Clone abb2.jpg|Ab Armor|
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
*Ab section should be completely contained under the chest and back armor. ||
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}

{{CRLtemplate|File:CLone cod and rear.jpg|Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}

{{CRLtemplate|File:Clone Belt copy.jpg|Belt|
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Detonator is centered on the back of belt.
*8 boxes total, 4 on each side of abdomen and attached to the belt. ||
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}

{{CRLtemplate|File:501st clone thigh armor 2.jpg|Thigh Armor|
*Armor should be painted matte or satin white.
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Rear of the thigh should have an indention.
*Down the outside of each thigh, there are 2 blue stripes spaced about an inch apart. These stripes line up with the stripes on the calves. ||
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. }}

{{CRLtemplate||Knee Armor|
*Armor should be painted matte or satin white.
*Knees should wrap around the front of the leg. From top center a raised detail line should be present.
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
*There is a blue stripe that follows the bottom curve of the knee plate.|
*Center strap should be primer gray.
*Connection between the knee and the strapping should have a detail clip.|}}

{{CRLtemplate|File:501st clone shin armor2.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed.
*Down the outside of each calf , there are 2 blue stripes spaced about an inch apart. These stripes line up with the stripes on the thighs. ||
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}

{{CRLtemplate|File:Clone shoes copy.jpg|Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
* Boots must be lace-less and have flat soles.
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
* This strap should be white.
*There should be no markings or labels from the shoe makers. The shoe soles should be gray. | | }}

{{CRLaccessories}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CT - 501st Legion

2013-03-13T01:20:29Z

BLACKSNAKE:

{{CRLheader|501st Clone Trooper|File:501st_model.jpg|CT4841|Sharon Langthorne}}

{{CRLdetinfo| 1111 |501st Clone Trooper|CT|Episode III: Revenge of the Sith|
The 501st Legion, later known as "Vader's Fist," was an elite unit of clone troopers commissioned by Supreme Chancellor Palpatine during the Clone Wars that later became a stormtrooper unit. The 501st fought in many battles, such as the Battle of Teth and the Battle of Coruscant, becoming one of the most well-known legions. It was the 501st that was led into the Jedi temple by Darth Vader and helped destroy the Jedi there. In 19 BBY, the 501st became Darth Vader's personal unit as he led them during Operation: Knightfall, in which the clones helped take down the Jedi, whom they believed to be traitors to the Republic. }}

{{CRLctnlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:501-Appo helmet copy.jpg|Helmet|

*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Visor - Black Visor.
*Helmet mohawk on dome.
*Starting on the nose of the helmet, there is a blue stripe about 1 inch wide going from the vents to the vocoder. From the middle of the two centermost vents to half an inch off the center eye curves, the area in between should be painted pale blue. Continuing from there, widening out to 3 inches from center of the mowhawk, the pale blue stripe continues. It then thins to 4 inches in the rear of the helmet squared off in the back, ¼ inch above the grey helmet wrap.
*Vertical stripes on each side of helmet cheeks that are dark blue in color.
*Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
*Primer grey stripe around back of dome.
*Ear caps are painted a dark grey.
*Helmet has the appearance of a neck ring.
*Helmet may have an optional enclosed complete neck ring that seals the helmet to the neck.|
*No additional requirements.|
*Helmet must have a full neck ring.}}

{{CRL-realistic-clone-neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:501st clone shoulder bells2.jpg |Shoulder Bells|
*Armor should be painted blue.
*Shoulders should be tear drop in shape with all rounded edges. | |
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}

{{CRLtemplate|File:Clone bicept copy.jpg|Upper Arm Armor|
*Armor should be painted matte or satin white.
*Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.||
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|‎File:Clone elbow copy.jpg|Elbow Armor|
*Armor should be painted matte or satin white.
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}

{{CRLtemplate| |Forearm Armor|
*Armor should be painted matte or satin white.
*Both left and right forearms should be mirror images of each other.
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
*The wrist of the forearm must have a blue stripe that wraps around the entire circumference of the forearm | |
*Compad has detail antenna on its left.
*Instead of a hard edge the top of the forearm has a bone ridge.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|File:Clone hand guards copy.jpg|Hand Plates|
*Armor should be painted matte or satin white.
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:501st clone chest plate2.jpg|Chest Armor|
*Armor should be painted matte or satin white.
*Two detail slots on right breast.
*Chest armor must have a blue stripe that begins at the center of the neck and extends down the chest plate to the bottom of the breast plate. From there it extends out towards the sides. Consult reference images for more detail.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. ||
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}

{{CRLtemplate|File:501st clone back plate 2.jpg|Back Armor|
*Armor should be painted matte or satin white.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Rear tank detailed area is painted blue.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. ||
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:Clone abb2.jpg|Ab Armor|
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
*Ab section should be completely contained under the chest and back armor. ||
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}

{{CRLtemplate|File:CLone cod and rear.jpg|Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}

{{CRLtemplate|File:Clone Belt copy.jpg|Belt|
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Detonator is centered on the back of belt.
*8 boxes total, 4 on each side of abdomen and attached to the belt. ||
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}

{{CRLtemplate|File:501st clone thigh armor 2.jpg|Thigh Armor|
*Armor should be painted matte or satin white.
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Rear of the thigh should have an indention.
*Down the outside of each thigh, there are 2 blue stripes spaced about an inch apart. These stripes line up with the stripes on the calves. ||
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. }}

{{CRLtemplate||Knee Armor|
*Armor should be painted matte or satin white.
*Knees should wrap around the front of the leg. From top center a raised detail line should be present.
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
*There is a blue stripe that follows the bottom curve of the knee plate.|
*Center strap should be primer gray.
*Connection between the knee and the strapping should have a detail clip.|}}

{{CRLtemplate|File:501st clone shin armor2.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed.
*Down the outside of each calf , there are 2 blue stripes spaced about an inch apart. These stripes line up with the stripes on the thighs. ||
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}

{{CRLtemplate|File:Clone shoes copy.jpg|Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
* Boots must be lace-less and have flat soles.
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
* This strap should be white.
*There should be no markings or labels from the shoe makers. The shoe soles should be gray. | | }}

{{CRLaccessories}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CT - 501st Legion

2013-03-08T18:37:03Z

BLACKSNAKE:

{{CRLheader|501st Clone Trooper|File:501st_model.jpg|CT4841|Sharon Langthorne}}

{{CRLdetinfo| 1111 |501st Clone Trooper|CT|Episode III: Revenge of the Sith|
The 501st Legion, later known as "Vader's Fist," was an elite unit of clone troopers commissioned by Supreme Chancellor Palpatine during the Clone Wars that later became a stormtrooper unit. The 501st fought in many battles, such as the Battle of Teth and the Battle of Coruscant, becoming one of the most well-known legions. It was the 501st that was led into the Jedi temple by Darth Vader and helped destroy the Jedi there. In 19 BBY, the 501st became Darth Vader's personal unit as he led them during Operation: Knightfall, in which the clones helped take down the Jedi, whom they believed to be traitors to the Republic. }}

{{CRLctnlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:501-Appo helmet copy.jpg|Helmet|

*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Visor - Black Visor.
*Helmet mohawk on dome.
*Starting on the nose of the helmet, there is a blue stripe about 1 inch wide going from the vents to the vocoder. From the middle of the two centermost vents to half an inch off the center eye curves, the area in between should be painted pale blue. Continuing from there, widening out to 3 inches from center of the mowhawk, the pale blue stripe continues. It then thins to 4 inches in the rear of the helmet squared off in the back, ¼ inch above the grey helmet wrap.
*Vertical stripes on each side of helmet cheeks that are dark blue in color.
*Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
*Primer grey stripe around back of dome.
*Ear caps are painted a dark grey.
*Helmet has the appearance of a neck ring.
*Helmet may have an optional enclosed complete neck ring that seals the helmet to the neck.|
*No additional requirements.|
*Helmet must have a full neck ring.}}

{{CRL-realistic-clone-neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:501st clone shoulder bells2.jpg |Shoulder Bells|
*Armor should be painted blue.
*Shoulders should be tear drop in shape with all rounded edges. | |
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}

{{CRLtemplate|File:Clone bicept copy.jpg|Upper Arm Armor|
*Armor should be painted matte or satin white.
*Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.||
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|‎File:Clone elbow copy.jpg|Elbow Armor|
*Armor should be painted matte or satin white.
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}

{{CRLtemplate| |Forearm Armor|
*Armor should be painted matte or satin white.
*Both left and right forearms should be mirror images of each other.
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
*The wrist of the forearm must have a blue stripe that wraps around the entire circumference of the forearm | |
*Compad has detail antenna on its left.
*Instead of a hard edge the top of the forearm has a bone ridge.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|File:Clone hand guards copy.jpg|Hand Plates|
*Armor should be painted matte or satin white.
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:501st clone chest plate2.jpg|Chest Armor|
*Armor should be painted matte or satin white.
*Two detail slots on right breast.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. ||
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}

{{CRLtemplate|File:501st clone back plate 2.jpg|Back Armor|
*Armor should be painted matte or satin white.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. ||
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:Clone abb2.jpg|Ab Armor|
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
*Ab section should be completely contained under the chest and back armor. ||
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}

{{CRLtemplate|File:CLone cod and rear.jpg|Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}

{{CRLtemplate|File:Clone Belt copy.jpg|Belt|
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Detonator is centered on the back of belt.
*8 boxes total, 4 on each side of abdomen and attached to the belt. ||
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}

{{CRLtemplate|File:501st clone thigh armor 2.jpg|Thigh Armor|
*Armor should be painted matte or satin white.
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Rear of the thigh should have an indention.
*Down the outside of each thigh, there are 2 blue stripes spaced about an inch apart. These stripes line up with the stripes on the calves. ||
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. }}

{{CRLtemplate||Knee Armor|
*Armor should be painted matte or satin white.
*Knees should wrap around the front of the leg. From top center a raised detail line should be present.
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
*There is a blue stripe that follows the bottom curve of the knee plate.|
*Center strap should be primer gray.
*Connection between the knee and the strapping should have a detail clip.|}}

{{CRLtemplate|File:501st clone shin armor2.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed.
*Down the outside of each calf , there are 2 blue stripes spaced about an inch apart. These stripes line up with the stripes on the thighs. ||
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}

{{CRLtemplate|File:Clone shoes copy.jpg|Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
* Boots must be lace-less and have flat soles.
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
* This strap should be white.
*There should be no markings or labels from the shoe makers. The shoe soles should be gray. | | }}

{{CRLaccessories}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CC CW-rex phase 2

2013-01-20T21:49:22Z

BLACKSNAKE:

{{CRLheader|Clone Captain Rex (Phase 2)|File:Rex front and back.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Captain Rex (Phase 2)|CC|The Clone Wars, season 4|Season 4 introduced new helmets and armor for the clones. This time Rex has a unique helmet sculpt, worn only by him.

'''Important: Since the armor has been updated significantly, a Clone Wars phase 2 Armor sculpt is required for approval. Phase 1 animated and/or movie style armor are not acceptable. '''
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLtemplate|File:REX ANIMATED HELMET.jpg|Helmet |
The Season 4 Rex helmet is a unique design, only worn by him. Features include:
* Low fin with a narrow ridge along each side.
* 2 blue "Jaig eyes" on the forehead, with 2 small triangles between them.
* The helmet has 27 black hash marks on the right side and 30 on the left.
* T shaped visor similar in shape Phase 1 clones. Visor is outlined in blue, with the line carrying down the center of the face to the chin.
* Grey frown with 3 black teeth on each side. Teeth may be cut out and backed with black mesh or painted.
* 1 small aerator type greeblie mounted at the front of each cheek recess.
* 2 larger aerators in the front. Aerators are black with a silver detail in the center. Detail may be aluminum mesh or painted.
* Mouth detail painted dark grey or black.
* 3 grey raised bumps on the left ear.
* Right ear has a grey rangefinder.
* Each cheek tube has 6 black stripes.
* The helmet has "weld lines" around the edges of the face as shown in reference images. These lines are a light blue, blended into dark blue, with dark orange edges. The weld marks should not have depth or dimension.|
*Helmet must be weathered.|}}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:REX ANIMATED PAULDRON.jpg|Mantle|
* Main body of the mantle is black.
* 4 trapezoidal grey panels on the front, across the chest.
* The right shoulder has a raised trim around the edges, and overlaps the back piece behind the shoulder. The overlap is fastened with a black snap (may be decorative or functional)
* The left shoulder extends out over the chest, and is made up of 3 blue panels. This shoulder detail may curve upward or lie relatively flat against the shoulder.
* Three black pouches are mounted at the right breast.
* The pouches have squared corners, and small flaps at the top fastened with 1 snap per pouch (may be functional or decorative)
* Pouches are custom constructed for the costume. Real world functional pouches should not be used. |
*Mantle must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED SHOULDER BELLS.jpg |Shoulders |
* Shoulders are a mirror image of each other.
* Shoulders taper at the center toward the bottom edge.
* Shoulders have a blue stripe down the center. |
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED BICEPS.jpg|Biceps|
*Biceps are cylindrical with no details / sculptural features.
* Biceps have a blue stripe down the center. |
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED ARM COMMPAD.jpg|Forearms|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Right forearm must have a compad that has 8 small buttons, 1 large main button, and 1 slightly smaller rectangular button. The compad must be painted blue.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm and does not extend past the arm. Elbow must have a blue stripe down the center. The edges of the stripe should be jagged / appear hand painted.
*Armor must have a blue stripe down the center. The edges of the stripe should be jagged / appear hand painted. The stripe is narrower at the wrist than at the bend of the elbow.
*There are 19 white hash marks in the blue stripe on the left forearm and 24 black hash marks on the right forearm on the left side of the blue stripe. |
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED HANDPLATEs.jpg|Handplates|
*Armor should be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other.
*Armor must have a blue stripe down the center. The edges of the stripe should be jagged / appear hand painted.
*There are 10 white hash marks painted on each hand plate close to the thumb. |
*Armor must be weathered.|}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:REX ANIMATED FRONTCHEST copy.jpg|Chest|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has an angled notch for the abdomen armor to fit into.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*The chest has 2 "weld lines" on either sides starting from the abdomen up to the armpits as shown in reference images. These lines are a light blue, blended into dark blue, with dark orange edges. The weld marks should not have depth or dimension.|
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED BACKPACK copy.jpg|Back|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the right of the back there three parallel lines. All detail painted a light grey.|
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED AB FRONT.jpg|Abdominal Plate|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Top edge of the armor is angled to match the chest.
*The ab armor protrudes out in the middle to better up with the chest.
*4 inset lines divide the ab plate into segments.
*A butted seam between ab plate and kidney is acceptable.|
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED KIDNEY BACK.jpg|Kidney Plate|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*A butted seam between ab plate and kidney is acceptable. |
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED BELT.jpg|Belt|
*Belt is approximately 3" tall and divided into 1.75" wide segments. The front segments have a key/slot detail.
*Belt boxes are mounted at the hips. Butted seams are permitted at this connection if required.
*Detonator is centered on the back of belt with no control buttons. The detonator has 2 lines set in approx 1/2" - 5/8" from the edges. Lines may be recessed or painted on.|
*Detonator lines must be recessed.
*Armor must be weathered.|}}

{{CRLtemplate|File:Blankwhite.gif|Kama|
*The kama must be made of black leather, leather like material, or heavy canvas.
*The kama has blue trim that should match the stripes on the armor.
*The front edges of the kama should line up with the outside edges of the front two panels of the belt.
*The back of the kama is split all the way up to the belt. ||}}

{{CRLtemplate|File:Animated Holsters.jpg|Holsters|
*Holsters must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. |
*Holsters must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED COD FRONT.jpg|Codpiece|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Cod and Posterior armor should connect at the hips. |
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED BUTT PLATE.jpg|Butt Plate|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.|
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED THIGH.jpg|Thighs|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown.
*Rear of the thigh should have an indentation.|
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED LOWER LEGS.jpg|Shins|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Knee armor is integrated with the lower leg.
*Knee armor must have a blue stripe down the center. The edges of the stripe should be jagged / appear hand painted.
* There are 20 Hash marks or Kill strips on the outsides of each calf, 8 on his left and 12 on his right.
*The armor must have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
*Armor must be weathered.|
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}

{{CRLtemplate|File:REX ANIMATED BOOTS.jpg|Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
*Boots have a center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap. |
*Boots must have accurate notched sole.
*Boots must be weathered|}}

{{CRLaccessories}}

{{CRLdc17pistol-animated}}

{{CRLtemplate|File:Blankwhite.gif|Helmet Light|||}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CT - 327th Star Corps

2013-01-20T03:14:41Z

BLACKSNAKE:

{{CRLheader|327th Star Corps. Trooper|File:327th full front and full back.jpg|DTR1/CT-6309|Andy Bauer}}

{{CRLdetinfo| 1111 |327th Star Corps. Trooper|CT|Episode III: Revenge of the Sith|

The 327th Star Corps was an elite corps of clone troopers during the Clone Wars. They were one of the most active units in the Grand Army of the Republic, and fell under the 2nd Sector Army and Systems Army Alpha. The troops of the 327th Star Corps were distinguished by striped yellow markings running the length of their armor and, as a result of Clone Marshal Commander Bly's ARC training, his troopers were allowed to don kama's and command pauldrons. }}

{{CRLctnlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:327th helmet.jpg|Helmet|

*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Visor - Black Visor.
*Helmet mohawk on dome.
*Vertical kill stripes on each side of helmet cheeks that are dark blue in color.
*Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
*Primer grey stripe around back of dome.
*Ear caps are painted a dark grey.
*There is a yellow stripe down the center of the helmet that ends at the chin of the helmet and squares off at the rear of the helmet.
*Helmet has the appearance of a neck ring.
*Helmet may have an optional enclosed complete neck ring that seals the helmet to the neck.|
*No additional requirements.|
*Helmet must have a full neck ring.}}

{{CRL-realistic-clone-neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:327th shoulder bell armor.jpg|Shoulder Bells|
*Armor should be painted matte or satin white.
*Yellow command stripe. Front part of the stripe is painted like any other command stripe. The rear part of the stripe should be placed in the center of the bell. This is a forward facing stripe.
*Shoulders should be tear drop in shape with all rounded edges. | |
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}

{{CRLtemplate|File:327th upper arms.jpg|Upper Arm Armor|
*Armor should be painted matte or satin white.
*Yellow stripe starts on the hard outside edge of the bicep and goes to the middle of the outside bicep. It is not the same as the EII command stripes.
*2 smaller white ammo boxes are attached to the right bicep on a grey strap.
*Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.||
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|File:327th elbow armor.jpg ‎ |Elbow Armor|
*Armor should be painted matte or satin white.
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}

{{CRLtemplate|File:327th forearm armor.jpg |Forearm Armor|
*Armor should be painted matte or satin white.
*There is a two inch Yellow stripe on the top part of the forearm. On the right arm it would cover over the compad. The com pad should be left white. This design should be matched on the left forearm. Acceptable options for the left arm would be to either add a second compad, in paint, leave an outline of a compad, or leave just the stripe.
*Both left and right forearms should be mirror images of each other.
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm. | |
*Compad has detail antenna on its left.
*Instead of a hard edge the top of the forearm has a bone ridge.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|File:327th hand plates.jpg |Hand Plates|
*Armor should be painted matte or satin white.
*There is a two inch Yellow stripe running down the center of the hand plate.
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:327th pauldron.jpg|Pauldron|
*Pauldron should be Episode III style.
*Mantle is black.
*Large shoulder plate over the left or right shoulder should be colored in burnt sienna.
*Small shoulder plate and panelling shall be all black.
*On the small shoulder plate side of the Pauldron, an ammo belt is strung down to the belt. | | }}

{{CRLtemplate|File:327th chest ammo belt.jpg|Chest Ammo Belt|
*3 white ammo boxes are attached to a grey strap on right side of chest. | | }}

{{CRLtemplate|File:327th chest armor.jpg |Chest Armor|
*Armor should be painted matte or satin white.
*Yellow command stripe approximately 2 inches wide marked center vertical from neck to lower return curve.
*Two detail slots on right breast.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. ||
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}

{{CRLtemplate|File:327th back armor.jpg|Back Armor|
*Armor should be painted matte or satin white.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. ||
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:327th ab armor.jpg |Ab Armor|
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
*Ab section should be completely contained under the chest and back armor. ||
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}

{{CRLtemplate|File:327th cod and posterior armor.jpg |Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}

{{CRLtemplate|File:327th_belt.jpg|Belt|
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Detonator is centered on the back of belt.
*8 boxes total, 4 on each side of abdomen and attached to the belt. ||
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}

{{CRLtemplate|File:327th kama.jpg|Kama|
* Kama should be kakki or tea brown color.
* The Kama should not be lined with matching color fabric.
* The rear of the Kama has a split that denotes it as a two piece .
* Kama should start at the front belt boxes.
* Kama should be from a heavy material like canvas or a tight weave burlap.
* Kama should flow to the bottom of your knee armor.
* There are two straps from the kama that connect to a command buckle centered to the front of the belt. | |}}

{{CRLtemplate|File:327th thigh armor.jpg |Thigh Armor|
*Armor should be painted matte or satin white.
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Rear of the thigh should have an indention. ||
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. }}

{{CRLtemplate|File:327th knee armor.jpg|Knee Armor|
*Armor should be painted matte or satin white.
*Knees should have a Yellow stripe that starts at the top and runs vertically down to the bottom of the knee.
*Knees should wrap around the front of the leg. From top center a raised detail line should be present.
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
*Center strap should be primer gray.
*Connection between the knee and the strapping should have a detail clip.|}}

{{CRLtemplate|File:327th lower leg armor.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. ||
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}

{{CRLtemplate|File:327th boots.jpg |Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
* Boots must be lace-less and have flat soles.
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
* This strap should be painted Yellow.
*Across the shoe just in front of detail strap another thin stripe painted Yellow should also be placed on the boot.
*There should be no markings or labels from the shoe makers. The shoe soles should be gray. | | }}

{{CRLtemplate|File:327th commander holsters.jpg|Commander Holsters|
*Hung from the belt and rest at the hip on each side. | | }}

{{CRLaccessories}}

{{CRL-dc17pistol-realistic}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CC CW-rex phase 2

2013-01-20T02:45:13Z

BLACKSNAKE:

{{CRLheader|Clone Captain Rex (Phase 2)|File:Rex front and back.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Captain Rex (Phase 2)|CC|The Clone Wars, season 4|Season 4 introduced new helmets and armor for the clones. This time Rex has a unique helmet sculpt, worn only by him.

'''Important: Since the armor has been updated significantly, a Clone Wars phase 2 Armor sculpt is required for approval. Phase 1 animated and/or movie style armor are not acceptable. '''
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLtemplate|File:REX ANIMATED HELMET.jpg|Helmet |
The Season 4 Rex helmet is a unique design, only worn by him. Features include:
* Low fin with a narrow ridge along each side.
* 2 blue "Jaig eyes" on the forehead, with 2 small triangles between them.
* The helmet has 27 black hash marks on the right side and 30 on the left.
* T shaped visor similar in shape Phase 1 clones. Visor is outlined in blue, with the line carrying down the center of the face to the chin.
* Grey frown with 3 black teeth on each side. Teeth may be cut out and backed with black mesh or painted.
* 1 small aerator type greeblie mounted at the front of each cheek recess.
* 2 larger aerators in the front. Aerators are black with a silver detail in the center. Detail may be aluminum mesh or painted.
* Mouth detail painted dark grey or black.
* 3 grey raised bumps on the left ear.
* Right ear has a grey rangefinder.
* Each cheek tube has 6 black stripes.
* The helmet has "weld lines" around the edges of the face as shown in reference images. These lines are a light blue, blended into dark blue, with dark orange edges. The weld marks should not have depth or dimension.|
*Helmet must be weathered.|}}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:REX ANIMATED PAULDRON.jpg|Mantle|
* Main body of the mantle is black.
* 4 trapezoidal grey panels on the front, across the chest.
* The right shoulder has a raised trim around the edges, and overlaps the back piece behind the shoulder. The overlap is fastened with a black snap (may be decorative or functional)
* The left shoulder extends out over the chest, and is made up of 3 blue panels. This shoulder detail may curve upward or lie relatively flat against the shoulder.
* Three black pouches are mounted at the right breast.
* The pouches have squared corners, and small flaps at the top fastened with 1 snap per pouch (may be functional or decorative)
* Pouches are custom constructed for the costume. Real world functional pouches should not be used. |
*Mantle must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED SHOULDER BELLS.jpg |Shoulders |
* Shoulders are a mirror image of each other.
* Shoulders taper at the center toward the bottom edge.
* Shoulders have a blue stripe down the center. |
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED BICEPS.jpg|Biceps|
*Biceps are cylindrical with no details / sculptural features.
* Biceps have a blue stripe down the center. |
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED ARM COMMPAD.jpg|Forearms|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Right forearm must have a compad that has 8 small buttons, 1 large main button, and 1 slightly smaller rectangular button. The compad must be painted blue.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm and does not extend past the arm. Elbow must have a blue stripe down the center. The edges of the stripe should be jagged / appear hand painted.
*Armor must have a blue stripe down the center. The edges of the stripe should be jagged / appear hand painted. The stripe is narrower at the wrist than at the bend of the elbow.
*There are 19 white hash marks in the blue stripe on the left forearm and 24 black hash marks on the right forearm on the left side of the blue stripe. |
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED HANDPLATEs.jpg|Handplates|
*Armor should be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Hand plates are mirror images of each other.
*Armor must have a blue stripe down the center. The edges of the stripe should be jagged / appear hand painted.
*There are 10 white hash marks painted on each hand plate close to the thumb. |
*Armor must be weathered.|}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:REX ANIMATED FRONTCHEST copy.jpg|Chest|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has an angled notch for the abdomen armor to fit into.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*The chest has 2 "weld lines" on either sides starting from the abdomen up to the armpits as shown in reference images. These lines are a light blue, blended into dark blue, with dark orange edges. The weld marks should not have depth or dimension.|
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED BACKPACK copy.jpg|Back|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the right of the back there three parallel lines. All detail painted a light grey.|
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED AB FRONT.jpg|Abdominal Plate|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Top edge of the armor is angled to match the chest.
*The ab armor protrudes out in the middle to better up with the chest.
*4 inset lines divide the ab plate into segments.
*A butted seam between ab plate and kidney is acceptable.|
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED KIDNEY BACK.jpg|Kidney Plate|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*A butted seam between ab plate and kidney is acceptable. |
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED BELT.jpg|Belt|
*Belt is approximately 3" tall and divided into 1.75" wide segments. The front segments have a key/slot detail.
*Belt boxes are mounted at the hips. Butted seams are permitted at this connection if required.
*Detonator is centered on the back of belt with no control buttons. The detonator has 2 lines set in approx 1/2" - 5/8" from the edges. Lines may be recessed or painted on.|
*Detonator lines must be recessed.
*Armor must be weathered.|}}

{{CRLtemplate|File:Blankwhite.gif|Kama|
*The kama must be made of black leather, leather like material, or heavy canvas.
*The kama has blue trim that should match the stripes on the armor.
*The front edges of the kama should line up with the outside edges of the front two panels of the belt.
*The back of the kama is split all the way up to the belt. ||}}

{{CRLtemplate|File:Animated Holsters.jpg|Holsters|
*Holsters must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. |
*Holsters must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED COD FRONT.jpg|Codpiece|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Cod and Posterior armor should connect at the hips. |
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED BUTT PLATE.jpg|Butt Plate|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.|
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED THIGH.jpg|Thighs|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown.
*Rear of the thigh should have an indentation.|
*Armor must be weathered.|}}

{{CRLtemplate|File:REX ANIMATED LOWER LEGS.jpg|Shins|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Knee armor is integrated with the lower leg.
*Knee armor must have a blue stripe down the center. The edges of the stripe should be jagged / appear hand painted.
*The armor must have a flat center triangle below the knee plate, with the single point facing downward.
*The calf detail of the armor has a ridge wrapping around the back of the leg.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
*Armor must be weathered.|
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}

{{CRLtemplate|File:REX ANIMATED BOOTS.jpg|Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
*Boots have a center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap. |
*Boots must have accurate notched sole.
*Boots must be weathered|}}

{{CRLaccessories}}

{{CRLdc17pistol-animated}}

{{CRLtemplate|File:Blankwhite.gif|Helmet Light|||}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CX CW-animated ARF-camo

2013-01-19T20:31:16Z

BLACKSNAKE:

{{CRLheader|ARF Trooper (Camo Deco)|File:CX-ARF-Camo.jpg|Ricky Torres|Ricky Torres}}

{{CRLdetinfo| 1111 |ARF Trooper (Camo Deco)|CX|The Clone Wars theatrical release.|
These clone soldiers were often tasked with scouting out the enemy position on the battlefield. Although stealthy and well-trained, recon troopers' duties differed from that of clone commandos or Advanced Recon Commandos as their focus was on gathering information about the enemy or carrying out surprise attacks. Some ARF troopers were deployed with camouflage paint to help them blend with their scenery. }}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|ARF Trooper Helmet|
* Clone Wars style ARF helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Helmet must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Smoked black lens.
* An animated visor shall be attached to the helmet just over the lens and surround the entire helmet just below the dome. The visor must be painted dark grey. Consult reference images for more detail.|
* Helmet must be weathered|}}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Shoulder Bells must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Upper Arm Armor must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Upper Arm Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
* Upper Arm Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Upper Arm Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
* Forearm Armor and CommPad must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Hand Plates must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Hand Plates are mirror images of each other. |
* Hand Plates must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Chest Armor must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Lower portion of the chest has a curved notch for the abdomen armor to fit into.
* Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
* Shoulder straps must be placed over the chest and back armor at the seams and painted with the same Digital Camoflage patterm as the rest of the chest. |
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Back Armor must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper.
* Shoulder straps should be placed over the chest and back armor at the seamsand painted with the same Digital Camoflage patterm as the rest of the chest.|
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Ab Armor must have a Digital Camoflage pattern painted in various shades of grey. Consult reference images for more detail.
* Top edge of the armor is curved to match the chest.
* The ab armor protrudes out in the middle to better up with the chest.
* 4 inset lines divide the ab plate into segments.
* A butted seam between ab plate and kidney is acceptable.|
* Ab Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Kidney Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Kidney Armo must have a Digital Camoflage pattern painted in various shades of grey. Consult reference images for more detail.
* A butted seam between ab plate and kidney is acceptable.|
* Kidney Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Cod Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Cod Armor must have a Digital Camoflage pattern must be painted in various shades of grey. Consult reference images for more detail. |
* Cod Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Posterior Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Posterior Armor must have a Digital Camoflage pattern painted in various shades of grey. Consult reference images for more detail.
* Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required. |
* Posterior Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Belt and Ammo Box's|
* Belt must be dark grey and look to be weathered. Consult reference images for more detail.
* Belt must have two belt box's one on each side the left and right of the belt mirrored images of each other.
* Belt box's must be painted dark grey and look to be weathered.
* 2 rectangular boxes are mounted at the hips. The top edge of the box is tapered town toward the outside. There is an inset detail near the top of each box.
* Must be mounted directly on top of the Cod and Posterior Armor.|
* Belt and Belt Boxes must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Thigh Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Thigh Armor must have a Digital Camoflage pattern painted in various shades of grey. Consult reference images for more detail.
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Leg Armor must have a Digital Camoflage pattern painted in various shades of grey. Consult reference images for more detail.
* Knee armor is integrated with the lower leg.
* The armor should have a flat center triangle below the knee plate, with the single point facing downward.
* The calf detail of the armor has a ridge wrapping around the back of the leg.
* Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin. |
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Boots|
* White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
* Boots have a center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap.
* Boots must be painted in various shades of grey in the Digital Camouflage pattern. |
* Boots must have accurate notched sole.
* Boots must be weathered. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CX CW-animated ARF-camo

2013-01-19T20:27:29Z

BLACKSNAKE: Initial creation

{{CRLheader|ARF Trooper (Camo Deco)|File:CX-ARF-Camo.jpg|Ricky Torres|Ricky Torres}}

{{CRLdetinfo| 1111 |ARF Trooper (Camo Deco)|CX|The Clone Wars theatrical release.|
These clone soldiers were often tasked with scouting out the enemy position on the battlefield. Although stealthy and well-trained, recon troopers' duties differed from that of clone commandos or Advanced Recon Commandos as their focus was on gathering information about the enemy or carrying out surprise attacks. Some ARF troopers were deployed with camouflage paint to help them blend with their scenery. }}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|ARF Trooper Helmet|
* Clone Wars style ARF helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Helmet must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Smoked black lens.
* An animated visor shall be attached to the helmet just over the lens and surround the entire helmet just below the dome. The visor must be painted dark grey. Consult reference images for more detail.
|* Helmet must be weathered|}}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Shoulder Bells must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Upper Arm Armor must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Upper Arm Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
* Upper Arm Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Upper Arm Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
* Forearm Armor and CommPad must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Hand Plates must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Hand Plates are mirror images of each other. |
* Hand Plates must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Chest Armor must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Lower portion of the chest has a curved notch for the abdomen armor to fit into.
* Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
* Shoulder straps must be placed over the chest and back armor at the seams and painted with the same Digital Camoflage patterm as the rest of the chest. |
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Back Armor must have a Digital Camoflage pattern painted in various shades of grey all over. Consult reference images for more detail.
* Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper.
* Shoulder straps should be placed over the chest and back armor at the seamsand painted with the same Digital Camoflage patterm as the rest of the chest.|
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Ab Armor must have a Digital Camoflage pattern painted in various shades of grey. Consult reference images for more detail.
* Top edge of the armor is curved to match the chest.
* The ab armor protrudes out in the middle to better up with the chest.
* 4 inset lines divide the ab plate into segments.
* A butted seam between ab plate and kidney is acceptable.|
* Ab Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Kidney Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Kidney Armo must have a Digital Camoflage pattern painted in various shades of grey. Consult reference images for more detail.
* A butted seam between ab plate and kidney is acceptable.|
* Kidney Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Cod Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Cod Armor must have a Digital Camoflage pattern must be painted in various shades of grey. Consult reference images for more detail. |
* Cod Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Posterior Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Posterior Armor must have a Digital Camoflage pattern painted in various shades of grey. Consult reference images for more detail.
* Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required. |
* Posterior Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Belt and Ammo Box's|
* Belt must be dark grey and look to be weathered. Consult reference images for more detail.
* Belt must have two belt box's one on each side the left and right of the belt mirrored images of each other.
* Belt box's must be painted dark grey and look to be weathered.
* 2 rectangular boxes are mounted at the hips. The top edge of the box is tapered town toward the outside. There is an inset detail near the top of each box.
* Must be mounted directly on top of the Cod and Posterior Armor.|
* Belt and Belt Boxes must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Thigh Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Thigh Armor must have a Digital Camoflage pattern painted in various shades of grey. Consult reference images for more detail.
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Leg Armor must have a Digital Camoflage pattern painted in various shades of grey. Consult reference images for more detail.
* Knee armor is integrated with the lower leg.
* The armor should have a flat center triangle below the knee plate, with the single point facing downward.
* The calf detail of the armor has a ridge wrapping around the back of the leg.
* Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin. |
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Boots|
* White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
* Boots have a center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap.
* Boots must be painted in various shades of grey in the Digital Camouflage pattern. |
* Boots must have accurate notched sole.
* Boots must be weathered. | }}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CT Phase 2 Grunt

2013-01-16T04:18:14Z

BLACKSNAKE:

{{CRLheader|Clone Trooper|File:.jpg|}}

{{CRLdetinfo| 1111 |Clone Trooper|TC|Episode III: Revenge of the Sith|
Clone troopers were an army of identical, genetically-modified clones of Jango Fett, created to serve in the Grand Army of the Republic during the conflict that came to be known as the Clone Wars. Cloned and raised in the cities of Kamino, the clone troopers trained and drilled since birth, and came to be regarded as one of the most efficient military forces ever to have existed in galactic history. This was not only due to their training, but also to their unwavering loyalty to the Galactic Republic and its leader, Supreme Chancellor Palpatine.

{{RL_approved}}}}

{{CRLctnlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:E3 Clone Helmet.jpg | Helmet|
*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Helmet must be painted matte or satin white.
*Visor - Mirrored Chrome or Black Visor
*Mohawk on dome has raised edges on the outside edges of the top.
*Tube stripes on each side are dark blue in color. There are 9 stripes per side
*Frown is charcoal grey in color and has 7 teeth – 1 in the middle and three on each side. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
*Primer grey stripe around back of dome.
*Bar above the visor wrapping around the sides is painted black.
*Vocoder (chip detail) is painted black.
*Aerators (cylinders on either side of the vocoder) are painted black, with the center round part painted silver.
*Ear bars are painted a dark grey. The raised edge around the ear cap is painted black.
*Rectangular “grid” on back of helmet painted black.|
*Helmet has the appearance of a neck ring. |
*Helmet has an enclosed complete neck ring that seals the helmet to the neck. }}

{{CRLtemplate|File:IMG 0411.jpg|Neck Seal|
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible.
*If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.|
*Neck seal to be black in color with vertical ribbing. |}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.| | }}

{{CRLtemplate|File:Clone shoulder bells copy.jpg|Shoulder Bells|
*Armor should be painted matte or satin white.
*Shoulders should be tear drop in shape with all rounded edges. | |
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}

{{CRLtemplate|File:Clone bicept copy.jpg|Upper Arm Armor|
*Armor should be painted matte or satin white.
*Should have a dimple on the lower area of the back of the arm. The outside must have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |}}

{{CRLtemplate|File:Clone elbow copy.jpg|Elbow Armor|
*Armor should be painted matte or satin white
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}

{{CRLtemplate|File:Clone gauntlets copy.jpg|Forearm Armor|
*Armor should be painted matte or satin white.
*Both left and right forearms should be mirror images of each other.
*Right forearm should have a compad that has 8 small buttons in 2 rows of 4,1 Large main button, and 1 slightly smaller rectangular button at the top closer to the elbow.
*Forearm tops should have a flattened triangular area that starts at the wrist and becomes a ridge that comes to a point at the top of the forearm.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |
*Compad has detail antenna on its left.
*Instead of a hard edge the top of the forearm has a bone ridge.}}

{{CRLtemplate|File:Clone hand guards copy.jpg|Hand Plates|
*Armor should be painted matte or satin white
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRLtemplate|File:Generic-black-gloves.jpg|Gloves|
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}

{{CRLtemplate|File:Clone chest copy.jpg|Chest Armor|
*Armor should be painted matte or satin white.
*Two detail slots on the bottom right of the right breast.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. |
|
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}

{{CRLtemplate|File:Clone back.jpg|Back Armor|
*Armor should be painted matte or satin white.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. |
|
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:Clone abb2.jpg|Ab Armor|
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
*Ab section should be completely contained under the chest and back armor. |
|
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}

{{CRLtemplate|File:CLone cod and rear.jpg|Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}

{{CRLtemplate|File:Clone Belt copy.jpg|Belt|
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Detonator is centered on the back of belt.
*8 boxes total, 4 on each side of abdomen and attached to the belt. |
|
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}

{{CRLtemplate|File:Clone thighs.jpg|Thigh Armor|
*Armor should be painted matte or satin white.
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Bottom rear of the thigh should have an indentation.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. |
|
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.}}

{{CRLtemplate|File:Clone knees copy.jpg|Knee Armor|
*Armor should be painted matte or satin white.
*Knees should wrap around the front of the leg. From top center a raised detail line should be present.
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
|
*Center strap should be primer gray.
*Connection between the knee and the strapping should have a detail clip.}}

{{CRLtemplate|File:Clone shins.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
|
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.
*Outside of the lower leg should have a pointed tip at the top and the inside of the lower leg should be rounded off at the top.}}

{{CRLtemplate|File:Clone shoes copy.jpg |Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
* Boots must be lace-less and have flat soles.
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
* This strap shall be white to match the boot.
*There shall be no markings or labels from the shoe makers. The shoe soles should be gray. | | }}

{{CRLaccessories}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|T}}

Costuming:CT Phase 2 Grunt

2013-01-16T04:09:32Z

BLACKSNAKE:

{{CRLheader|Clone Trooper|File:.jpg|}}

{{CRLdetinfo| 1111 |Clone Trooper|TC|Episode III: Revenge of the Sith|
Clone troopers were an army of identical, genetically-modified clones of Jango Fett, created to serve in the Grand Army of the Republic during the conflict that came to be known as the Clone Wars. Cloned and raised in the cities of Kamino, the clone troopers trained and drilled since birth, and came to be regarded as one of the most efficient military forces ever to have existed in galactic history. This was not only due to their training, but also to their unwavering loyalty to the Galactic Republic and its leader, Supreme Chancellor Palpatine.

{{RL_approved}}}}

{{CRLctnlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:E3 Clone Helmet.jpg | Helmet|
*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Helmet must be painted matte or satin white.
*Visor is Black.
*Mohawk on dome has raised edges on the outside edges of the top.
*Tube stripes on each side are dark blue in color. There are 9 stripes per side
*Frown is charcoal grey in color and has 7 teeth – 1 in the middle and three on each side. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
*Primer grey stripe around back of dome.
*Bar above the visor wrapping around the sides is painted black.
*Vocoder (chip detail) is painted black.
*Aerators (cylinders on either side of the vocoder) are painted black, with the center round part painted silver.
*Ear bars are painted a dark grey. The raised edge around the ear cap is painted black.
*Rectangular “grid” on back of helmet painted black.|
*Helmet has the appearance of a neck ring. |
*Helmet has an enclosed complete neck ring that seals the helmet to the neck. }}

{{CRLtemplate|File:IMG 0411.jpg|Neck Seal|
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible.
*If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.|
*Neck seal to be black in color with vertical ribbing. |}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.| | }}

{{CRLtemplate|File:Clone shoulder bells copy.jpg|Shoulder Bells|
*Armor should be painted matte or satin white.
*Shoulders should be tear drop in shape with all rounded edges. | |
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}

{{CRLtemplate|File:Clone bicept copy.jpg|Upper Arm Armor|
*Armor should be painted matte or satin white.
*Should have a dimple on the lower area of the back of the arm. The outside must have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |}}

{{CRLtemplate|File:Clone elbow copy.jpg|Elbow Armor|
*Armor should be painted matte or satin white
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}

{{CRLtemplate|File:Clone gauntlets copy.jpg|Forearm Armor|
*Armor should be painted matte or satin white.
*Both left and right forearms should be mirror images of each other.
*Right forearm should have a compad that has 8 small buttons in 2 rows of 4,1 Large main button, and 1 slightly smaller rectangular button at the top closer to the elbow.
*Forearm tops should have a flattened triangular area that starts at the wrist and becomes a ridge that comes to a point at the top of the forearm.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |
*Compad has detail antenna on its left.
*Instead of a hard edge the top of the forearm has a bone ridge.}}

{{CRLtemplate|File:Clone hand guards copy.jpg|Hand Plates|
*Armor should be painted matte or satin white
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRLtemplate|File:Generic-black-gloves.jpg|Gloves|
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}

{{CRLtemplate|File:Clone chest copy.jpg|Chest Armor|
*Armor should be painted matte or satin white.
*Two detail slots on the bottom right of the right breast.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. |
|
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}

{{CRLtemplate|File:Clone back.jpg|Back Armor|
*Armor should be painted matte or satin white.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. |
|
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:Clone abb2.jpg|Ab Armor|
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
*Ab section should be completely contained under the chest and back armor. |
|
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}

{{CRLtemplate|File:CLone cod and rear.jpg|Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}

{{CRLtemplate|File:Clone Belt copy.jpg|Belt|
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Detonator is centered on the back of belt.
*8 boxes total, 4 on each side of abdomen and attached to the belt. |
|
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}

{{CRLtemplate|File:Clone thighs.jpg|Thigh Armor|
*Armor should be painted matte or satin white.
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Bottom rear of the thigh should have an indentation.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. |
|
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.}}

{{CRLtemplate|File:Clone knees copy.jpg|Knee Armor|
*Armor should be painted matte or satin white.
*Knees should wrap around the front of the leg. From top center a raised detail line should be present.
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
|
*Center strap should be primer gray.
*Connection between the knee and the strapping should have a detail clip.}}

{{CRLtemplate|File:Clone shins.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
|
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.
*Outside of the lower leg should have a pointed tip at the top and the inside of the lower leg should be rounded off at the top.}}

{{CRLtemplate|File:Clone shoes copy.jpg |Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
* Boots must be lace-less and have flat soles.
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
* This strap shall be white to match the boot.
*There shall be no markings or labels from the shoe makers. The shoe soles should be gray. | | }}

{{CRLaccessories}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|T}}

Costuming:CT Phase 2 Grunt

2013-01-16T04:02:49Z

BLACKSNAKE:

{{CRLheader|Clone Trooper|File:.jpg|}}

{{CRLdetinfo| 1111 |Clone Trooper|TC|Episode III: Revenge of the Sith|
Clone troopers were an army of identical, genetically-modified clones of Jango Fett, created to serve in the Grand Army of the Republic during the conflict that came to be known as the Clone Wars. Cloned and raised in the cities of Kamino, the clone troopers trained and drilled since birth, and came to be regarded as one of the most efficient military forces ever to have existed in galactic history. This was not only due to their training, but also to their unwavering loyalty to the Galactic Republic and its leader, Supreme Chancellor Palpatine.

{{RL_approved}}}}

{{CRLctnlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:E3 Clone Helmet.jpg | Helmet|
*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Helmet must be painted matte or satin white.
*Visor - Mirrored Chrome or Black Visor.
*Mohawk on dome has raised edges on the outside edges of the top.
*Tube stripes on each side are dark blue in color. There are 9 stripes per side
*Frown is charcoal grey in color and has 7 teeth – 1 in the middle and three on each side. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
*Primer grey stripe around back of dome.
*Bar above the visor wrapping around the sides is painted black.
*Vocoder (chip detail) is painted black.
*Aerators (cylinders on either side of the vocoder) are painted black, with the center round part painted silver.
*Ear bars are painted a dark grey. The raised edge around the ear cap is painted black.
*Rectangular “grid” on back of helmet painted black.|
*Helmet has the appearance of a neck ring. |
*Helmet has an enclosed complete neck ring that seals the helmet to the neck. }}

{{CRLtemplate|File:IMG 0411.jpg|Neck Seal|
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible.
*If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.|
*Neck seal to be black in color with vertical ribbing. |}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.| | }}

{{CRLtemplate|File:Clone shoulder bells copy.jpg|Shoulder Bells|
*Armor should be painted matte or satin white.
*Shoulders should be tear drop in shape with all rounded edges. | |
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}

{{CRLtemplate|File:Clone bicept copy.jpg|Upper Arm Armor|
*Armor should be painted matte or satin white.
*Should have a dimple on the lower area of the back of the arm. The outside must have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |}}

{{CRLtemplate|File:Clone elbow copy.jpg|Elbow Armor|
*Armor should be painted matte or satin white
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}

{{CRLtemplate|File:Clone gauntlets copy.jpg|Forearm Armor|
*Armor should be painted matte or satin white.
*Both left and right forearms should be mirror images of each other.
*Right forearm should have a compad that has 8 small buttons in 2 rows of 4,1 Large main button, and 1 slightly smaller rectangular button at the top closer to the elbow.
*Forearm tops should have a flattened triangular area that starts at the wrist and becomes a ridge that comes to a point at the top of the forearm.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |
*Compad has detail antenna on its left.
*Instead of a hard edge the top of the forearm has a bone ridge.}}

{{CRLtemplate|File:Clone hand guards copy.jpg|Hand Plates|
*Armor should be painted matte or satin white
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRLtemplate|File:Generic-black-gloves.jpg|Gloves|
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}

{{CRLtemplate|File:Clone chest copy.jpg|Chest Armor|
*Armor should be painted matte or satin white.
*Two detail slots on the bottom right of the right breast.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. |
|
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}

{{CRLtemplate|File:Clone back.jpg|Back Armor|
*Armor should be painted matte or satin white.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. |
|
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:Clone abb2.jpg|Ab Armor|
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
*Ab section should be completely contained under the chest and back armor. |
|
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}

{{CRLtemplate|File:CLone cod and rear.jpg|Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}

{{CRLtemplate|File:Clone Belt copy.jpg|Belt|
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Detonator is centered on the back of belt.
*8 boxes total, 4 on each side of abdomen and attached to the belt. |
|
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}

{{CRLtemplate|File:Clone thighs.jpg|Thigh Armor|
*Armor should be painted matte or satin white.
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Bottom rear of the thigh should have an indentation.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. |
|
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.}}

{{CRLtemplate|File:Clone knees copy.jpg|Knee Armor|
*Armor should be painted matte or satin white.
*Knees should wrap around the front of the leg. From top center a raised detail line should be present.
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
|
*Center strap should be primer gray.
*Connection between the knee and the strapping should have a detail clip.}}

{{CRLtemplate|File:Clone shins.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
|
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.
*Outside of the lower leg should have a pointed tip at the top and the inside of the lower leg should be rounded off at the top.}}

{{CRLtemplate|File:Clone shoes copy.jpg |Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
* Boots must be lace-less and have flat soles.
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
* This strap shall be white to match the boot.
*There shall be no markings or labels from the shoe makers. The shoe soles should be gray. | | }}

{{CRLaccessories}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|T}}

Costuming:CT Phase 2 Grunt

2013-01-16T03:58:55Z

BLACKSNAKE:

{{CRLheader|Clone Trooper|File:.jpg|}}

{{CRLdetinfo| 1111 |Clone Trooper|TC|Episode III: Revenge of the Sith|
Clone troopers were an army of identical, genetically-modified clones of Jango Fett, created to serve in the Grand Army of the Republic during the conflict that came to be known as the Clone Wars. Cloned and raised in the cities of Kamino, the clone troopers trained and drilled since birth, and came to be regarded as one of the most efficient military forces ever to have existed in galactic history. This was not only due to their training, but also to their unwavering loyalty to the Galactic Republic and its leader, Supreme Chancellor Palpatine.

{{RL_approved}}}}

{{CRLctnlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:E3 Clone Helmet.jpg | Helmet|
*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Helmet must be painted matte or satin white.
*Visor - Mirrored Chrome or Black Visor.
*Mohawk on dome has raised edges on the outside edges of the top.
*6 blue or black vents on each side of helmet cheeks.
*Frown is charcoal grey in color and has 7 teeth – 1 in the middle and three on each side. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
*Primer grey stripe around back of dome.
*Bar above the visor wrapping around the sides is painted black.
*Vocoder (chip detail) is painted black.
*Aerators (cylinders on either side of the vocoder) are painted black, with the center round part painted silver.
*Ear bars are painted a dark grey. The raised edge around the ear cap is painted black.
*Rectangular “grid” on back of helmet painted black.|
*Helmet has the appearance of a neck ring. |
*Helmet has an enclosed complete neck ring that seals the helmet to the neck. }}

{{CRLtemplate|File:IMG 0411.jpg|Neck Seal|
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible.
*If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.|
*Neck seal to be black in color with vertical ribbing. |}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.| | }}

{{CRLtemplate|File:Clone shoulder bells copy.jpg|Shoulder Bells|
*Armor should be painted matte or satin white.
*Shoulders should be tear drop in shape with all rounded edges. | |
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}

{{CRLtemplate|File:Clone bicept copy.jpg|Upper Arm Armor|
*Armor should be painted matte or satin white.
*Should have a dimple on the lower area of the back of the arm. The outside must have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |}}

{{CRLtemplate|File:Clone elbow copy.jpg|Elbow Armor|
*Armor should be painted matte or satin white
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}

{{CRLtemplate|File:Clone gauntlets copy.jpg|Forearm Armor|
*Armor should be painted matte or satin white.
*Both left and right forearms should be mirror images of each other.
*Right forearm should have a compad that has 8 small buttons in 2 rows of 4,1 Large main button, and 1 slightly smaller rectangular button at the top closer to the elbow.
*Forearm tops should have a flattened triangular area that starts at the wrist and becomes a ridge that comes to a point at the top of the forearm.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |
*Compad has detail antenna on its left.
*Instead of a hard edge the top of the forearm has a bone ridge.}}

{{CRLtemplate|File:Clone hand guards copy.jpg|Hand Plates|
*Armor should be painted matte or satin white
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRLtemplate|File:Generic-black-gloves.jpg|Gloves|
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}

{{CRLtemplate|File:Clone chest copy.jpg|Chest Armor|
*Armor should be painted matte or satin white.
*Two detail slots on the bottom right of the right breast.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. |
|
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}

{{CRLtemplate|File:Clone back.jpg|Back Armor|
*Armor should be painted matte or satin white.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. |
|
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:Clone abb2.jpg|Ab Armor|
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
*Ab section should be completely contained under the chest and back armor. |
|
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}

{{CRLtemplate|File:CLone cod and rear.jpg|Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}

{{CRLtemplate|File:Clone Belt copy.jpg|Belt|
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Detonator is centered on the back of belt.
*8 boxes total, 4 on each side of abdomen and attached to the belt. |
|
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}

{{CRLtemplate|File:Clone thighs.jpg|Thigh Armor|
*Armor should be painted matte or satin white.
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Bottom rear of the thigh should have an indentation.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. |
|
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.}}

{{CRLtemplate|File:Clone knees copy.jpg|Knee Armor|
*Armor should be painted matte or satin white.
*Knees should wrap around the front of the leg. From top center a raised detail line should be present.
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
|
*Center strap should be primer gray.
*Connection between the knee and the strapping should have a detail clip.}}

{{CRLtemplate|File:Clone shins.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
|
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.
*Outside of the lower leg should have a pointed tip at the top and the inside of the lower leg should be rounded off at the top.}}

{{CRLtemplate|File:Clone shoes copy.jpg |Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
* Boots must be lace-less and have flat soles.
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
* This strap shall be white to match the boot.
*There shall be no markings or labels from the shoe makers. The shoe soles should be gray. | | }}

{{CRLaccessories}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|T}}

Costuming:CT - 327th Star Corps

2013-01-16T03:41:33Z

BLACKSNAKE:

{{CRLheader|327th Star Corps. Trooper|File:327th full front and full back.jpg|DTR1/CT-6309|Andy Bauer}}

{{CRLdetinfo| 1111 |327th Star Corps. Trooper|CT|Episode III: Revenge of the Sith|

The 327th Star Corps was an elite corps of clone troopers during the Clone Wars. They were one of the most active units in the Grand Army of the Republic, and fell under the 2nd Sector Army and Systems Army Alpha. The troops of the 327th Star Corps were distinguished by striped yellow markings running the length of their armor and, as a result of Clone Marshal Commander Bly's ARC training, his troopers were allowed to don kama's and command pauldrons. }}

{{CRLctnlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:327th helmet.jpg|Helmet|

*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Visor - Black Visor.
*Helmet mohawk on dome.
*Vertical kill stripes on each side of helmet cheeks that are dark blue in color.
*Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
*Primer grey stripe around back of dome.
*Ear caps are painted a dark grey.
*There is a yellow stripe down the center of the helmet that ends at the chin of the helmet and squares off at the rear of the helmet.
*Helmet has the appearance of a neck ring.
*Helmet may have an optional enclosed complete neck ring that seals the helmet to the neck.|
*No additional requirements.|
*Helmet must have a full neck ring.}}

{{CRL-realistic-clone-neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:327th shoulder bell armor.jpg|Shoulder Bells|
*Armor should be painted matte or satin white.
*Yellow command stripe. Front part of the stripe is painted like any other command stripe. The rear part of the stripe should be placed in the center of the bell. This is a forward facing stripe.
*Shoulders should be tear drop in shape with all rounded edges. | |
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}

{{CRLtemplate|File:327th upper arms.jpg|Upper Arm Armor|
*Armor should be painted matte or satin white.
*Yellow stripe starts on the hard outside edge of the bicep and goes to the middle of the outside bicep. It is not the same as the EII command stripes.
*2 smaller white ammo boxes are attached to the right bicep on a grey strap.
*Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.||
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|File:327th elbow armor.jpg ‎ |Elbow Armor|
*Armor should be painted matte or satin white.
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}

{{CRLtemplate|File:327th forearm armor.jpg |Forearm Armor|
*Armor should be painted matte or satin white.
*There is a two inch Yellow stripe on the top part of the forearm. On the right arm it would cover over the compad. The com pad should be left white. This design should be matched on the left forearm. Acceptable options for the left arm would be to either add a second compad, in paint, leave an outline of a compad, or leave just the stripe.
*Both left and right forearms should be mirror images of each other.
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm. | |
*Compad has detail antenna on its left.
*Instead of a hard edge the top of the forearm has a bone ridge.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|File:327th hand plates.jpg |Hand Plates|
*Armor should be painted matte or satin white.
*There is a two inch Yellow stripe running down the center of the hand plate.
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:327th pauldron.jpg|Pauldron|
*Pauldron should be Episode III style.
*The mantle over the left or right shoulder should be colored in the command color burnt sienna.
*Right shoulder mantle and panelling on the remainder of the pauldron shall be all black.
*On the right side of the Pauldron, an ammo belt is strung down to the belt. | | }}

{{CRLtemplate|File:327th chest ammo belt.jpg|Chest Ammo Belt|
*3 white ammo boxes are attached to a grey strap on right side of chest. | | }}

{{CRLtemplate|File:327th chest armor.jpg |Chest Armor|
*Armor should be painted matte or satin white.
*Yellow command stripe approximately 2 inches wide marked center vertical from neck to lower return curve.
*Two detail slots on right breast.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. ||
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}

{{CRLtemplate|File:327th back armor.jpg|Back Armor|
*Armor should be painted matte or satin white.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. ||
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:327th ab armor.jpg |Ab Armor|
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
*Ab section should be completely contained under the chest and back armor. ||
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}

{{CRLtemplate|File:327th cod and posterior armor.jpg |Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}

{{CRLtemplate|File:327th_belt.jpg|Belt|
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Detonator is centered on the back of belt.
*8 boxes total, 4 on each side of abdomen and attached to the belt. ||
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}

{{CRLtemplate|File:327th kama.jpg|Kama|
* Kama should be kakki or tea brown color.
* The Kama should not be lined with matching color fabric.
* The rear of the Kama has a split that denotes it as a two piece .
* Kama should start at the front belt boxes.
* Kama should be from a heavy material like canvas or a tight weave burlap.
* Kama should flow to the bottom of your knee armor.
* There are two straps from the kama that connect to a command buckle centered to the front of the belt. | |}}

{{CRLtemplate|File:327th thigh armor.jpg |Thigh Armor|
*Armor should be painted matte or satin white.
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Rear of the thigh should have an indention. ||
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. }}

{{CRLtemplate|File:327th knee armor.jpg|Knee Armor|
*Armor should be painted matte or satin white.
*Knees should have a Yellow stripe that starts at the top and runs vertically down to the bottom of the knee.
*Knees should wrap around the front of the leg. From top center a raised detail line should be present.
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
*Center strap should be primer gray.
*Connection between the knee and the strapping should have a detail clip.|}}

{{CRLtemplate|File:327th lower leg armor.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. ||
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}

{{CRLtemplate|File:327th boots.jpg |Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
* Boots must be lace-less and have flat soles.
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
* This strap should be painted Yellow.
*Across the shoe just in front of detail strap another thin stripe painted Yellow should also be placed on the boot.
*There should be no markings or labels from the shoe makers. The shoe soles should be gray. | | }}

{{CRLtemplate|File:327th commander holsters.jpg|Commander Holsters|
*Hung from the belt and rest at the hip on each side. | | }}

{{CRLaccessories}}

{{CRL-dc17pistol-realistic}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|C}}

Costuming:CC commander cody-phase2

2013-01-03T04:00:02Z

BLACKSNAKE:

{{CRLheader|Clone Commander Cody|File:Cody front and back CRL copy.jpg|Douglas Danco |Douglas Danco }}

{{CRLdetinfo| 1111 |Clone Commander Cody|CC|Episode III: Revenge of the Sith|
}}

{{CRLctnlevels}}

{{CRLwipgmlapproval}}

{{CRLrequirements}}

{{CRLfooter|CTN_CRL|C}}

{{CRLtemplate|File:Helmet copy.jpg| Helmet|
* Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
* Visor - Black Visor.
* There shall be 2 mohawks one located on each side of the center helmet fin painted in “tan” color or equivalent.
* Vertical kill stripes shall be on each side of helmet cheeks that are dark blue in color.
* Helmet frown shall be charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
* Grey stripe around back of dome.
* Ear caps shall be painted a dark grey.
* Face, ears, and dome are white. Mohawk and remainder of the helmet are mustard yellow. There is a sandy brown stripe down the center of the helmet that ends at the nose of the helmet and squares off at the rear of the helmet.
* A “Camera” shall be mounted to top left part of the dome.
* There are two antenna’s mounted to the helmet. One on each side of the helmet.
* The visor over the lens shall be painted in “Tropical Orange” or equivalent. There shall be a white pinstripe detail on the visor.
* Around the aerators there shall be a sunburst detail that is painted in the “Tropical Orange” or equivalent. }}

{{CRLtemplate|File:IMG 0411.jpg|Neck Seal|
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.| |}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.| | }}

{{CRLtemplate|File:CODYShoulderBells copy.jpg|Shoulder Bells|
* Armor should be painted “Tropical orange” or equivalent matte.
* Shoulders should be tear drop in shape with all rounded edges.
* Shoulder bells shall have two channels in them.
* Left shoulder bell shall have the correct screen accurate white “script” on it and the communicator attached to it. | |
* Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}

{{CRLtemplate|File:CODYBiceps copy.jpg|Upper Arm Armor|
* Armor shall be painted matte or satin white.
* The left upper arm armor shall have a light grey stripe that starts on the hard outside edge of the bicep and be approximately 1 ½” wide. This stripe should show distinct markings or wear with the white showing through the stripe.
* On the right upper arm armor, there shall be a golden brown strap holding a “pen” that is mounted to the back of the armor.
* Each upper arm should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded. | |
* Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|File:CODYElbows copy.jpg|Elbow Armor|
* Armor should be painted “Tropical Orange” or equivalent.
* There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces. This inset should be painted black.
*Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}

{{CRLtemplate|File:CODYGauntelts.jpg|Forearm Armor|
* Armor should be painted matte or satin white.
* Both left and right forearms shall be mirror images of each other.
* A light grey stripe starts on the hard outside edge of the bicep and be approximately 1 ½” wide. This stripe should show signs of wear with the white showing through the stripe. On the right arm it would cover over the compad. The com pad should be left white. This design should be matched on the left forearm | |
*Compad has detail antenna on its left.
*Instead of a hard edge the top of the forearm has a bone ridge.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}

{{CRLtemplate|File:CODYHandGuards copy.jpg|Hand Plates|
* Armor should be painted “Tropical Orange” or equivalent.
* Hand plates are mirror images of each other.
* Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRLtemplate|File:Generic-black-gloves.jpg|Gloves|
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}

{{CRLtemplate|File:CODYChest copy.jpg|Chest Armor|
* Armor should be painted matte or satin white.
* There shall be a center stripe approximately 2” wide painted in “Tropical Orange” or equivalent. This stripe starts at the bottom of the chest armor and goes to approximately the sternum area of the armor. These stripes should show signs of wear that allows the white to show through them.
* There are two smaller stripes approximately 1 ½” wide painted in “Tropical Orange” that are at opposite angles to each other on either side of the center stripe. These stripes should show signs of wear that allows the white to show through them.
* Two detail slots on right breast painted in the “Tropical Orange” or equivalent.
* There are three “scratches” in the top left section of the armor. These are to be painted in a dark color. The middle of these scratches is the longest extending to just past the middle of the armor.
* There is an ID badge that is mounted to the top left of the chest just underneath the three scratches. The main part of the badge is painted in a matte or satin white. This badge shall have 4 buttons. The one closest to the center of the chest shall be a dark purple, the next one the “Tropical Orange” or equivalent, the last two shall be a light blue color. The bottom of the badge shall be a light grey color.
* Chest and back plate should match together at the sides with no gap, just a seam line.
* Shoulder straps should be placed underneath the chest to connect to the back |
|
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}

{{CRLtemplate|File:CODYback2.jpg|Back Armor|
* Armor should be painted matte or satin white.
* Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
* Shoulder straps should be placed underneath the chest to connect to the back. |
|
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points. }}

{{CRLtemplate|File:CODYJetpack copy copy.jpg|Jetpack|
* Jetpack should be painted matte or satin white. Center “thruster” shall be painted in a golden brown color. Just above the “thruster” shall be painted a light grey.
* Jetpack measurements should be approximately 15 ¾” Long and 8 ½” wide. }}

{{CRLtemplate|File:CODYAbSection copy.jpg|Ab Armor|
* Armor should be painted in a light grey color.
* Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
* Ab section should wrap around the wearers body and be sealed at the sides or at the back.
* Ab section should be completely contained under the chest and back armor. |
|
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}

{{CRLtemplate|File:CODYCod copy.jpg|Cod and Posterior Armor|
* Armor should be painted matte or satin white.
* There shall be a stripe approximately 2” wide painted in “Tropical Orange” or equivalent. This stripe should line up with the center stripe in the chest armor. This stripe should show signs of wear that allows the white to show through. It should go down to approximately the center of the Cod armor.
* Cod and Posterior armor should connect at the hips. | |
* Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}

{{CRLtemplate|File:CODYBelt copy.jpg|Belt|
* Armor should be painted light grey.
* The belt boxes to the left side of the belt from center shall be painted in “Tropical Orange” or equivalent. The belt boxes to the right side of the belt from center shall be painted in light grey. The two boxes near the back of the belt shall be painted in a golden brown color.
* Ammo Belt with boxes and detonator.
* Detonator shall be centered on the back of belt. The “caps” of the Detonator are painted in a light yellow color.
* 8 boxes total, on each side of abdomen and attached to the belt. |
|
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}

{{CRLtemplate|File:CODYThighs copy.jpg|Thigh Armor|
* Thighs should be painted matte or satin white.
* On the left thigh armor there is a stripe painted in “Tropical Orange” or equivalent. This stripe should show signs of wear that allows the white to show through. This stripe starts on the inside of section of the armor and moves diagonally to the top left of the armor stopping before it reaches the edge.
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Rear of the thigh should have an indention.|
|
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.
*Gray leg strap should be made of leather.
*Leg pouch has the correct shape and may be functional.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. }}

{{CRLtemplate|File:Blankwhite.gif|Knee Armor|
* Armor should be painted “Tropical Orange” or equivalent.
* Knees should wrap around the front of the leg. From top center a raised detail line should be present.
* Knees should be strapped to the leg via a “Tropical Orange” or equivalent strap with a raised center area painted in a light grey that wraps around the leg and connects on both sides of the Knee.|
|
*Center strap should be primer gray.
*Connection between the knee and the strapping should have a detail clip.}}

{{CRLtemplate|File:Clone shins.jpg|Lower Leg Armor|
* Armor should be painted matte or satin white.
* Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
* Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
* Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
|
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}

{{CRLtemplate|File:Clone shoes copy.jpg|Boots|
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles. The boots have armor detail to include a natural seam at the toe and a gray strap that goes over the top of the foot with two protruding disks at each side of the strap. There should be no markings or labels from the shoe makers. Boot soles should be primer gray. | | }}

{{CRLaccessories}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLtemplate|File:Blankwhite.gif|Emperor Palpatine Holodisk Communicator| | | }}

{{CRLfooter|CTN_CRL|C}}

Costuming:TC CW Jek

2013-01-02T03:09:57Z

BLACKSNAKE:

{{CRLheader|Clone Trooper Jek|File:Missingprofile.jpg|none|non}}

{{CRLdetinfo| 1111 |Clone Trooper Jek|CC|The Clone Wars|Jek is one of the first troopers we meet in Season 1, Episode 1.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif| Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Black visor extends down through the entire frown area.
* Narrow fin on dome.
* A dark scarlet outline around visor, extending down to mouth indent.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Primer grey stripe around back of dome.
* Raised white circle at the back of the helmet.
* Rectangular indent at the back of the helmet may be primer grey or heavily weathered white. |
* Helmet must be weathered.| }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* A dark scarlet stripe painted down the center of the shoulders.
* A white Republic Senate symbol is present in the stripe and towards the bottom of the shoulders.
* Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
*A dark scarlet stripe runs down the center of the armor. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow. The compad is white.
* A dark scarlet stripe runs down the center of the armor.
* Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
* Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
* Armor must be painted a dark scarlet. If weathered, the weathering should be shades of grey.
* Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRL-TC_animated_chest}}

{{CRL-TC_animated_back}}

{{CRLtemplate|File:Blankwhite.gif|Bandolier|
* A black bandolier must be worn from the right shoulder to the left hip. | | }}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRL-TC_animated_thighs}}

{{CRLtemplate|File:CC_generic_animated_holsters.jpeg|Holsters|
* Holsters must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Holsters may connect to the belt via straps.|
* Holsters must be weathered | }}

{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Knee armor is integrated with the lower leg.
* Center of knee armor is painted dark scarlet.
* The armor should have a flat center triangle below the knee plate, with the single point facing downward.
* The calf detail of the armor has a ridge wrapping around the back of the leg.
* Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin. |
* Armor must be weathered. | }}

{{CRL-TC_animated_boots}}

{{CRLaccessories}}

{{CRLdc17pistol-animated}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|T}}

Costuming:CC CW-animated gree

2012-12-27T21:56:01Z

BLACKSNAKE: Added Bandolier

{{CRLheader|Clone Commander Gree|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Commander Gree|CC|The Clone Wars, seasons 1-3|Gree leads the 41st Elite, first appearing in Season 1, Episode 8 "Bombad Jedi".
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* A dark slate green stripe shall be painted on the helmet starting at the chin and continue up the face on the inside edges of the cheeks over the brow trim and then gradualy start to curve to the back of the helmet ending just at the back of the helmets brow trim. The fin shall remain satin white and weathered. Consult reference images for more detail.
* The inside panel of each check shall be painted dark slate green and weathered.
* Black visor extends down through the entire frown area.
* Narrow fin on dome.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Grey stripe runs around back of dome.
* Raised satin white circle at the back of the helmet.
* Rectangular indent at the back of the helmet shall be grey or heavily weathered black.|
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Shoulder armor shall have a 3 to 3 1/2" dark slate green stripe running down the center from top to bottom and look to be weathered.Consult reference images for more detail.
* Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
* Shoulder bells must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Upper arm armor shall have a dark slate green stripe that continues down from the shoulder bell and splits at the center of the bicep and runs around the front and back to meet together on the inside of the upper arm armor.
* Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Upper arm armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
* Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
* Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
* Elbow plate attached to the forearm shall be painted dark slate green. Consult reference images for more detail.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Forearm armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Chest armor shall have one dark slate green stripe that starts just under the neck trim of the chest armor and runs down the chest and continues on to the ab plate. Consult reference images for more detail.
* The dark slate green shoulder bell stripes are continued up on to the shoulders of the chest and back armor stopping at the neck line just as the stripe on the front chest.
* Shoulder straps are not required on this armor, however if they are used they should be painted to mach the flow of color as it is painted with out.
* Chest armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Back armor shall have the dark slate green stripes continued from the front around the bottom edge and then meet at the spine curving and running up the back stopping at the detail plate. Leaving the back detail plate satin white. The dark slate green stripe then continues from the top of the detail plate and ends at the neck trim again. Consult reference images for more detail.
* The circle detail on the back detail plate shall be painted grey.
* Back armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Bandolier|
* A black bandolier must be worn from the right shoulder to the left hip. | | }}

{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* The Ab armor shall have the dark slate green stripe continued from the chest plate from the top and curve out to the sides and around to the back and kidney plate. Consult reference images for more detail.
* Ab armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Kidney Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* The kidney armor shall be painted dark slate green and weathered.
* Kidney armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Cod Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Cod armor shall have a dark slate green stripe running down the sides of the hips, on the cod and butt plate 2" wide. Consult reference images for more detail.
* Cod armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Butt Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Butt armor shall have a dark slate green stripe running down the sides of the hips, on the butt and cod plate 2" wide. Consult reference images for more detail.
* Butt armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Belt and Ammo Box's|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Belt must have two satin white belt box's one on each side the left and right of the belt mirrored images of each other.
* The Thermal detonator shall be painted grey. Consult reference images for more detail.
* belt and box's must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Thigh Armor|
* Armor must be painted dark slate green and weathered. | }}

{{CRL-TC_animated_shins}}

{{CRL-TC_animated_boots}}
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Boots must be weathered. | }}

{{CRLaccessories}}

{{CRLdc17pistol-animated}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

Costuming:TC CW Jek

2012-12-27T21:53:20Z

BLACKSNAKE: Initial creation

{{CRLheader|Clone Trooper Jek|File:Missingprofile.jpg|none|non}}

{{CRLdetinfo| 1111 |Clone Trooper Jek|CC|The Clone Wars|Jek is one of the first troopers we meet in Season 1, Episode 1.
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif| Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Black visor extends down through the entire frown area.
* Narrow fin on dome.
* A dark scarlet outline around visor, extending down to mouth indent.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Primer grey stripe around back of dome.
* Raised white circle at the back of the helmet.
* Rectangular indent at the back of the helmet may be primer grey or heavily weathered white. |
* Helmet must be weathered.| }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* A dark scarlet stripe painted down the center of the shoulders.
* A white Republic Senate symbol is present in the stripe and towards the bottom of the shoulders.
* Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder. |
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
*A dark scarlet stripe runs down the center of the armor. |
*Armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow. The compad is white.
* A dark scarlet stripe runs down the center of the armor.
* Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
* Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep. |
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
* Armor must be painted a dark scarlet. If weathered, the weathering should be shades of grey.
* Hand plates are mirror images of each other. |
* Armor must be weathered. | }}

{{CRL-generic_black_gloves}}

{{CRL-TC_animated_chest}}

{{CRL-TC_animated_back}}

{{CRLtemplate|File:Blankwhite.gif|Bandolier|
* A black bandolier must be worn from the right shoulder to the left hip. | | }}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRL-TC_animated_thighs}}

{{CRL-CC_animated_holsters}}

{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Knee armor is integrated with the lower leg.
* Center of knee armor is painted dark scarlet.
* The armor should have a flat center triangle below the knee plate, with the single point facing downward.
* The calf detail of the armor has a ridge wrapping around the back of the leg.
* Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin. |
* Armor must be weathered. | }}

{{CRL-TC_animated_boots}}

{{CRLaccessories}}

{{CRLdc17pistol-animated}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|T}}

Costuming:CC CW-animated gree

2012-12-27T21:06:54Z

BLACKSNAKE: added DC-17 hand blaster, modified thigh section to reference green color.

{{CRLheader|Clone Commander Gree|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Commander Gree|CC|The Clone Wars, seasons 1-3|Gree leads the 41st Elite, first appearing in Season 1, Episode 8 "Bombad Jedi".
}}

{{CRLctnlevels}}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif|Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* A dark slate green stripe shall be painted on the helmet starting at the chin and continue up the face on the inside edges of the cheeks over the brow trim and then gradualy start to curve to the back of the helmet ending just at the back of the helmets brow trim. The fin shall remain satin white and weathered. Consult reference images for more detail.
* The inside panel of each check shall be painted dark slate green and weathered.
* Black visor extends down through the entire frown area.
* Narrow fin on dome.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Grey stripe runs around back of dome.
* Raised satin white circle at the back of the helmet.
* Rectangular indent at the back of the helmet shall be grey or heavily weathered black.|
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Shoulder armor shall have a 3 to 3 1/2" dark slate green stripe running down the center from top to bottom and look to be weathered.Consult reference images for more detail.
* Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
* Shoulder bells must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Upper arm armor shall have a dark slate green stripe that continues down from the shoulder bell and splits at the center of the bicep and runs around the front and back to meet together on the inside of the upper arm armor.
* Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Upper arm armor must be weathered. |}}

{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
* Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
* Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
* Elbow plate attached to the forearm shall be painted dark slate green. Consult reference images for more detail.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Forearm armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Chest armor shall have one dark slate green stripe that starts just under the neck trim of the chest armor and runs down the chest and continues on to the ab plate. Consult reference images for more detail.
* The dark slate green shoulder bell stripes are continued up on to the shoulders of the chest and back armor stopping at the neck line just as the stripe on the front chest.
* Shoulder straps are not required on this armor, however if they are used they should be painted to mach the flow of color as it is painted with out.
* Chest armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Back Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Back armor shall have the dark slate green stripes continued from the front around the bottom edge and then meet at the spine curving and running up the back stopping at the detail plate. Leaving the back detail plate satin white. The dark slate green stripe then continues from the top of the detail plate and ends at the neck trim again. Consult reference images for more detail.
* The circle detail on the back detail plate shall be painted grey.
* Back armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* The Ab armor shall have the dark slate green stripe continued from the chest plate from the top and curve out to the sides and around to the back and kidney plate. Consult reference images for more detail.
* Ab armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Kidney Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* The kidney armor shall be painted dark slate green and weathered.
* Kidney armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Cod Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Cod armor shall have a dark slate green stripe running down the sides of the hips, on the cod and butt plate 2" wide. Consult reference images for more detail.
* Cod armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Butt Armor|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Butt armor shall have a dark slate green stripe running down the sides of the hips, on the butt and cod plate 2" wide. Consult reference images for more detail.
* Butt armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Belt and Ammo Box's|
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Belt must have two satin white belt box's one on each side the left and right of the belt mirrored images of each other.
* The Thermal detonator shall be painted grey. Consult reference images for more detail.
* belt and box's must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Thigh Armor|
* Armor must be painted dark slate green and weathered. | }}

{{CRL-TC_animated_shins}}

{{CRL-TC_animated_boots}}
* Armor must be matte or satin white. If weathered, the weathering should be shades of grey.
* Boots must be weathered. | }}

{{CRLaccessories}}

{{CRLdc17pistol-animated}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

Costuming:TC CW-animated fives for hevy

2012-12-21T17:42:37Z

BLACKSNAKE:

{{CRLheader|Clone Trooper Fives (For Hevy)|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Trooper Fives (For Hevy)|TC|The Clone Wars Season 3|
Fives returns in the opening episode of Season 3 with revised armor featuring a tribute to Hevy, his comrade lost in Rookies.}}

{{CRLctnlevels}}

{{CRLlmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif| Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
* Black visor extends down through the entire frown area.
* Narrow fin on dome painted blue.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Primer grey stripe around back of dome.
* Raised white circle and rectangular white indent at the back of the helmet.|
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:TC_CW_echo_for_hevy_shoulders.jpg|Shoulder Bells, Left Shoulder|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Blue stripe painted down center of shoulder.
*Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells, Right Shoulder|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue stripe painted down center of shoulder.
* On the center of the blue stripe is a painting of a rotary canon with the aurabesh inscription "For Hevy" below the canon.
*Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
*Armor must be weathered. | }}

{{CRLtemplate|File:TC_CW_echo_for_hevy_bicep.jpg|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Blue stripe painted down center of biceps.
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. |}}

{{CRLtemplate|File:TC_CW_echo_for_hevy_forearm.jpg|Forearm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Blue stripe painted down center of forearms.
*Center diamond of elbow armor painted blue.
*Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.|
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:TC_animated_chest.jpg|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Shoulder straps must be placed over the chest and back armor at the seams. |
*Armor must be weathered. | }}

{{CRL-TC_animated_back}}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRLtemplate|File:TC_animated_thighs.jpg|Thigh Armor, Right Leg|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered.|}}

{{CRLtemplate|File:Blankwhite.gif|Thigh Armor, Left Leg|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown on the left side of the ridge line. The markings should be a series of 6 horizontal lines in the pattern (top to bottom) thick line followed by 2 thin lines, another thick line, a thinner line, then thick line. Consult reference images for more detail.
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered.|}}

{{CRL-TC_animated_shins}}

{{CRL-TC_animated_boots}}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|T}}

Costuming:TC CW-animated fives for hevy

2012-12-21T17:36:01Z

BLACKSNAKE:

{{CRLheader|Clone Trooper Fives (For Hevy)|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Trooper Fives (For Hevy)|TC|The Clone Wars Season 3|
Fives returns in the opening episode of Season 3 with revised armor featuring a tribute to Hevy, his comrade lost in Rookies.}}

{{CRLctnlevels}}

{{CRLlmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif| Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
* Black visor extends down through the entire frown area.
* Narrow fin on dome painted blue.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Primer grey stripe around back of dome.
* Raised white circle and rectangular white indent at the back of the helmet.|
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:TC_CW_echo_for_hevy_shoulders.jpg|Shoulder Bells, Left Shoulder|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
*Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells, Right Shoulder|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
* On the center of the blue stripe is a painting of a rotary canon with the aurabesh inscription "For Hevy" below the canon.
*Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
*Armor must be weathered. | }}

{{CRLtemplate|File:TC_CW_echo_for_hevy_bicep.jpg|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. |}}

{{CRLtemplate|File:TC_CW_echo_for_hevy_forearm.jpg|Forearm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
*Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.|
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:TC_animated_chest.jpg|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Shoulder straps must be placed over the chest and back armor at the seams. |
*Armor must be weathered. | }}

{{CRL-TC_animated_back}}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRLtemplate|File:TC_animated_thighs.jpg|Thigh Armor, Right Leg|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered.|}}

{{CRLtemplate|File:Blankwhite.gif|Thigh Armor, Left Leg|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown on the left side of the ridge line. The markings should be a series of 6 horizontal lines in the pattern (top to bottom) thick line followed by 2 thin lines, another thick line, a thinner line, then thick line. Consult reference images for more detail.
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered.|}}

{{CRL-TC_animated_shins}}

{{CRL-TC_animated_boots}}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|T}}

Costuming:TC CW-animated fives for hevy

2012-12-21T16:41:46Z

BLACKSNAKE:

{{CRLheader|Clone Trooper Fives (For Hevy)|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}

{{CRLdetinfo| 1111 |Clone Trooper Fives (For Hevy)|TC|The Clone Wars Season 3|
Fives returns in the opening episode of Season 3 with revised armor featuring a tribute to Hevy, his comrade lost in Rookies.}}

{{CRLctnlevels}}

{{CRLlmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Blankwhite.gif| Helmet|
* Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
* Helmet must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
* Black visor extends down through the entire frown area.
* Narrow fin on dome painted blue.
* Raised bump at each ear, 1" - 1.25" in diameter.
* 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
* Primer grey stripe around back of dome.
* Raised white circle and rectangular white indent at the back of the helmet.|
* Helmet must be weathered. | }}

{{CRL-TC_animated_neckseal}}

{{CRL-generic-undersuit}}

{{CRLtemplate|File:TC_CW_echo_for_hevy_shoulders.jpg|Shoulder Bells, Left Shoulder|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
*Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
*Armor must be weathered. | }}

{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells, Right Shoulder|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
* On the center of the blue stripe is a painting of a rotary canon with the aurabesh inscription "For Hevy" below the canon.
*Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.|
*Armor must be weathered. | }}

{{CRLtemplate|File:TC_CW_echo_for_hevy_bicep.jpg|Upper Arm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
*Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
*Armor must be weathered. |}}

{{CRLtemplate|File:TC_CW_echo_for_hevy_forearm.jpg|Forearm Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown.
*Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
*Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.|
* Armor must be seamless. No visible traces of how the armor was assembled should be shown.
* Armor must be weathered. | }}

{{CRL-TC_animated_handplates}}

{{CRL-generic_black_gloves}}

{{CRLtemplate|File:TC_animated_chest.jpg|Chest Armor|
*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
*Shoulder straps must be placed over the chest and back armor at the seams. |
*Armor must be weathered. | }}

{{CRL-TC_animated_back}}

{{CRL-TC_animated_ab}}

{{CRL-TC_animated_kidney}}

{{CRL-TC_animated_cod}}

{{CRL-TC_animated_butt}}

{{CRL-TC_animated_belt_boxes}}

{{CRLtemplate|File:TC_animated_thighs.jpg|Thigh Armor, Right Leg|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered.|}}

{{CRLtemplate|File:Blankwhite.gif|Thigh Armor, Left Leg|
* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
* Blue markings must be painted as shown on the left side of the ridge line. The markings should be a series of 6 horizontal lines in the pattern (top to bottom) thick line followed by 2 thin lines, another thick line, a thinner line, then thick line.(see reference pictures for a detailed reference).
* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Armor must be seamless. No visible traces of how the armor was assembled should be shown. |
* Armor must be weathered.|}}

{{CRL-TC_animated_shins}}

{{CRL-TC_animated_boots}}

{{CRLaccessories}}

{{CRLdc15s-animated}}

{{CRLdc15a-animated}}

{{CRLfooter|CTN_CRL|T}}

Costuming:GM GalacticMarine

2012-12-20T23:45:15Z

BLACKSNAKE:

{{CRLheader|Galactic Marine Clone Trooper|File:GM_main.jpg|GM6838|Greg Gatzka}}

{{CRLdetinfo| 1111 |Galactic Marine Clone Trooper|GM|Episode III: Revenge of the Sith|
The Galactic Marines, originally known as the 21st Nova Corps of the 4th Sector Army, was an elite unit that was created as the Grand Army of the Republic diversified during the Clone Wars. Galactic Marines wore special body armor with maroon coloration. They were usually armed with DC-15A blaster rifles. The Marines were distinguished by their unique visor gear: synthmesh designed to keep out various hazards such as snow, sand, airborne fungus, and ash.}}

{{CRLctnlevels}}

{{CRLwipgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:GM_helmet.jpg| Helmet|
*GM Clone Style Helmet – Fanmade helmet
*Helmet is maroon in color.
*Black or Green Visor -Welding Shield above grade 5. Lenses may be flat or bubble, either is acceptable.
*Helmet has a rectangular vent with grating mesh.
*White Cowl that wraps around the entire helmet.|
* No changes required above base level. |
*There is a gray lining around the eyes.
*Brow and edge of the helmet have a thin bead detail trim. }}

{{CRLtemplate|File:Bacara_neckseal.jpg|Neck Seal|
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.| |}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos. The only areas visible are the arms. Tops alone are more than acceptable.| | }}

{{CRLtemplate|File:GM_shoulders.jpg|Shoulder Bells|
*Armor should be painted maroon.
*Left Shoulder is the same as the Barc (Kashyyk) trooper
*Right shoulder is TB shape with oval ridges. | | }}

{{CRLtemplate|File:GM_biceps.jpg|Upper Arm Armor|
*Armor should be painted maroon.
*Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.
*A black strap with three small white ammo boxes should wrap around the right arm. | |
*Inner part of ammo packs should be painted off white/beige. }}

{{CRLtemplate|File:GM_elbows.jpg|Elbow Armor|
*Armor should be painted matte or satin white
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.
*Both elbows have ammo box details placed on the back.}}

{{CRLtemplate|File:GM_forearms.jpg|Forearm Armor|
*Armor should be painted maroon.
*Both left and right forearms should be mirror images of each other.
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |
*Instead of a hard edge the top of the forearm has a bone ridge. }}

{{CRLtemplate|File:GM_handplates.jpg|Hand Plates|
*Armor should be painted maroon.
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRLtemplate|File:Generic-black-gloves.jpg|Gloves|
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}

{{CRLtemplate|File:GM_epaulet.jpg|Shoulder Epaulets|
Shoulders should be covered with a black tri fold, dual panel epaulet. They connect to the chest and back and are covered by they cowl draped from the helmet | | }}

{{CRLtemplate|File:GM_chest2.jpg|Chest Armor|
*Armor should be painted maroon.
*Chest Specific shape to the GM to include 3 greeblies on front/lower area of chest plate
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Down right side of the chest an ammo belt should be stung that has 3 large white ammo boxes and 1 small black ammo box.|
|
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points.
*Inner part of ammo packs should be painted off white/beige. }}

{{CRLtemplate|File:GM_back.jpg|Back Armor|
*Armor should be painted maroon.
*Back is smooth without a detail plate, but with attachments for a backpack
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. |
|
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:GM_backpack.jpg|Back Pack|
*Back Pack should be painted matte or satin white.
*Consists of a main shell and two side shells over a base mounted to the back armor.
*Has a detonator type attachment underneath the main shell it has smooth end caps and ridges. There are no detonator keys. | | }}

{{CRLtemplate|File:GM_belt.jpg|Belt|
*Belt should be made from white canvas.
*Belt has 2 large and 2 small canvas pouches accompanied by 2 metal like buckle looking greeblies on the front and a kama buckle in the front center of the belt.
*Top of belt should be mounted just below the chest/back plates with little or no gap visible
*There are 4 small canvas pouches on the rear of the belt. | | }}

{{CRLtemplate|File:GM_kama.jpg|Kama|
*The Kama should be maroon. The Kama may be lined with white color fabric trim. The rear of the Kama has a triangle split. Kama should start at the front belt boxes. Kama should be from a heavy material like denim or duck cloth similar to that seen in the films. The Kama should flow to the bottom of your knee armor.
*There is a strap on each side that comes from the inside of the kama front and clips to the command buckle. | | }}

{{CRLtemplate|File:GM_pants.jpg|Overalls|
*The Overall trousers are a gray.
*One rectangular cargo pocket with flap centered on the front of each thigh. Upper portion of undersuit may be back or dark grey | |
*Inside the front of the pants there should be a cod armor insert.}}

{{CRLtemplate|File:GM_knees.jpg|Knee Armor|
*Armor should be painted matte or satin white.
*Knees should cup the front of the leg.
*Knees should be strapped to the leg via a white strap that wraps around the leg and connects on both sides of the Knee. | |
*Left leg knee strap should be grey.}}

{{CRLtemplate|File:GM_shins.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower shin/calf armor specific to a GM to include 2 sets of white straps with clip greeblies each. **These are the same shins as seen on the Barc (Kashyyk) trooper. | |
*Calves should be seamless.}}

{{CRLtemplate|File:GM_boots.jpg|Boots|
*Must be white leather or leather-like with the sole pattern to match as closely as possible to the movie costume. Most identifiable features include a high arch pattern on the inside of the sole, four profile "swoops" between the sole and leather. Snaps on both side of heel upper to secure the boot armor is suggested. Boot Armor Plates should cover the top and sides of the boot and curves up in front and over the bottom of the shim. | | }}

{{CRLaccessories}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|G}}

Costuming:GM GalacticMarine

2012-12-20T23:35:53Z

BLACKSNAKE: changed color of left knee armor strap for level 3 cert.

{{CRLheader|Galactic Marine Clone Trooper|File:GM_main.jpg|GM6838|Greg Gatzka}}

{{CRLdetinfo| 1111 |Galactic Marine Clone Trooper|GM|Episode III: Revenge of the Sith|
The Galactic Marines, originally known as the 21st Nova Corps of the 4th Sector Army, was an elite unit that was created as the Grand Army of the Republic diversified during the Clone Wars. Galactic Marines wore special body armor with maroon coloration. They were usually armed with DC-15A blaster rifles. The Marines were distinguished by their unique visor gear: synthmesh designed to keep out various hazards such as snow, sand, airborne fungus, and ash.}}

{{CRLctnlevels}}

{{CRLwipgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:GM_helmet.jpg| Helmet|
*GM Clone Style Helmet – Fanmade helmet
*Helmet is maroon in color.
*Black or Green Visor -Welding Shield above grade 5. Lenses may be flat or bubble, either is acceptable.
*Helmet has a rectangular vent with grating mesh.
*White Cowl that wraps around the entire helmet.|
* No changes required above base level. |
*There is a gray lining around the eyes.
*Brow and edge of the helmet have a thin bead detail trim. }}

{{CRLtemplate|File:Bacara_neckseal.jpg|Neck Seal|
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.| |}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos. The only areas visible are the arms. Tops alone are more than acceptable.| | }}

{{CRLtemplate|File:GM_shoulders.jpg|Shoulder Bells|
*Armor should be painted maroon.
*Left Shoulder is the same as the Barc (Kashyyk) trooper
*Right shoulder is TB shape with oval ridges. | | }}

{{CRLtemplate|File:GM_biceps.jpg|Upper Arm Armor|
*Armor should be painted maroon.
*Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.
*A black strap with three small white ammo boxes should wrap around the right arm. | |
*Inner part of ammo packs should be painted off white/beige. }}

{{CRLtemplate|File:GM_elbows.jpg|Elbow Armor|
*Armor should be painted matte or satin white
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.
*Both elbows have ammo box details placed on the back.}}

{{CRLtemplate|File:GM_forearms.jpg|Forearm Armor|
*Armor should be painted maroon.
*Both left and right forearms should be mirror images of each other.
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |
*Instead of a hard edge the top of the forearm has a bone ridge. }}

{{CRLtemplate|File:GM_handplates.jpg|Hand Plates|
*Armor should be painted maroon.
*Hand plates are mirror images of each other.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}

{{CRLtemplate|File:Generic-black-gloves.jpg|Gloves|
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}

{{CRLtemplate|File:GM_epaulet.jpg|Shoulder Epaulets|
Shoulders should be covered with a black tri fold, dual panel epaulet. They connect to the chest and back and are covered by they cowl draped from the helmet | | }}

{{CRLtemplate|File:GM_chest2.jpg|Chest Armor|
*Armor should be painted maroon.
*Chest Specific shape to the GM to include 3 greeblies on front/lower area of chest plate
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Down right side of the chest an ammo belt should be stung that has 3 large white ammo boxes and 1 small black ammo box.|
|
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points.
*Inner part of ammo packs should be painted off white/beige. }}

{{CRLtemplate|File:GM_back.jpg|Back Armor|
*Armor should be painted maroon.
*Back is smooth without a detail plate, but with attachments for a backpack
*Chest and back plate should match together at the sides with no gap, just a seam line.
*Shoulder straps should be placed underneath the chest to connect to the back. |
|
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}

{{CRLtemplate|File:GM_backpack.jpg|Back Pack|
*Armor should be painted matte or satin white.
*Consists of a main shell and two side shells over a base mounted to the back armor.
*Has a detonator type attachment underneath the main shell it has smooth end caps and ridges. There are no detonator keys. | | }}

{{CRLtemplate|File:GM_belt.jpg|Belt|
*Armor should be made from white canvas.
*Belt has 2 large and 2 small canvas pouches accompanied by 2 metal like buckle looking greeblies on the front and a kama buckle in the front center of the belt.
*Top of belt should be mounted just below the chest/back plates with little or no gap visible
*There are 4 small canvas pouches on the rear of the belt. | | }}

{{CRLtemplate|File:GM_kama.jpg|Kama|
*The Kama should be maroon. The Kama may be lined with white color fabric trim. The rear of the Kama has a triangle split. Kama should start at the front belt boxes. Kama should be from a heavy material like denim or duck cloth similar to that seen in the films. The Kama should flow to the bottom of your knee armor.
*There is a strap on each side that comes from the inside of the kama front and clips to the command buckle. | | }}

{{CRLtemplate|File:GM_pants.jpg|Overalls|
*The Overall trousers are a gray.
*One rectangular cargo pocket with flap centered on the front of each thigh. Upper portion of undersuit may be back or dark grey | |
*Inside the front of the pants there should be a cod armor insert.}}

{{CRLtemplate|File:GM_knees.jpg|Knee Armor|
*Armor should be painted matte or satin white.
*Knees should cup the front of the leg.
*Knees should be strapped to the leg via a white strap that wraps around the leg and connects on both sides of the Knee. | |
*Left leg knee strap should be grey.}}

{{CRLtemplate|File:GM_shins.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Lower shin/calf armor specific to a GM to include 2 sets of white straps with clip greeblies each. **These are the same shins as seen on the Barc (Kashyyk) trooper. | |
*Calves should be seamless.}}

{{CRLtemplate|File:GM_boots.jpg|Boots|
*Must be white leather or leather-like with the sole pattern to match as closely as possible to the movie costume. Most identifiable features include a high arch pattern on the inside of the sole, four profile "swoops" between the sole and leather. Snaps on both side of heel upper to secure the boot armor is suggested. Boot Armor Plates should cover the top and sides of the boot and curves up in front and over the bottom of the shim. | | }}

{{CRLaccessories}}

{{CRLdc15s-realistic}}

{{CRLdc15a-realistic}}

{{CRLfooter|CTN_CRL|G}}