Databank - User contributions [en]

Costuming:SL-Maul

2013-06-13T06:07:57Z

Muppet: Protected "Costuming:SL-Maul" ([edit=sysop] (indefinite) [move=sysop] (indefinite))

{{CRLheader|Darth Maul, The Phantom Menace|File:SL_maul_full.jpeg|SL-6426|Brian Gibson}}

{{CRLdetinfo|1110|Darth Maul, The Phantom Menace |SL|Star Wars Episode I: The Phantom Menace|The apprentice of Darth Sidious, this Iridonian Zabrak heralded the return of the Sith in a flash of red and black. }}

{{CRLsldlevels}}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate-onelevel|File:SL_maul_face.jpeg|Face and Head|
*There are ten horns; one on top, seven crowning the head, and one on each temple.
*Each horn has a unique shape, is not longer than two inches, and the color resembles that of rotting bone.
*The head is shaved, but a high quality bald cap may also be employed.
*There is a small, silver, ball-stud earring (real or magnetic) worn in the upper part of the left ear.
*The facial paints are red and black with a matte finish and are to be applied in the specific pattern shown. Key stress areas are:
**The ears (inside and out), behind the ears, around the eyes, and neck are completely black.
**The lower lip is not black; it is mainly red with three black accents.
**The bridge of the nose is predominately red (aside from the vertical black pattern in the center); the black section around the eyes does not extend that far onto the bridge of the nose.
**The black section around the eyes covers and goes above the outer half of each eyebrow.
**The two “lines” (that connect the inner eyebrows to the two horns off the center horn) are not straight. They start in predominantly a vertical manner, wind in an “S” fashion, after which they become vertical again just before connecting to the black tear-drop areas surrounding the two horns.
*The teeth are treated as if molted and decayed with black and brown tooth enamels.
*'''Masks of any type are NOT allowed for this character. Please contact the Legion Membership Officers AND the Detachment Staff for any questions concerning this matter.'''|
*There should be a little red at the base of the horns, but not so much that it is blatantly obvious.
*The top (rear) horn should be the longest at approximately two inches, the ones crowning the head should be approximately one and one-half inches long, and the temple horns should be approximately one-half inches long.|}}

{{CRLtemplate-nolevels|File:SL_maul_eye.jpeg|Sith Eyes|
*The contact lenses are described as a fiery yellow transitioning into a brilliant red.

*While considered an essential part of this character, the contact lens requirement will be waived for 501st acceptance if the applicant cannot wear contact lenses for health related reasons. All persons utilizing contact lenses are encouraged to first see their optometrist for a fitting.||}}

{{CRLtemplate-onelevel|File:SL_maul_basetunic.jpeg|Base Tunic|
*Black linen, blend, or a fabric with an equivalent appearance and weight.
*The collar is ribbed with four quilted lines running around the neck to where the Tunic closes in front. It closes in a “V” fashion at the base of the neck and does not overlap.
*There is no visible zipper, or attachment device of any kind, in full costume.
*The length of the tunic extends to just above the knees.
*The side seams are open from the waist down.
*There is no open seam on the backside.|
*The Base Tunic should be linen, silk, or a blend.
*The side seams should be open from just below the arms down; only two to three inches is actually sewn together.|}}

{{CRLtemplate-onelevel|File:SL_maul_sithrobe.jpeg|Sith Robe|
*Worn over the Base Tunic, has components of varying length, and is a lightweight black raw silk noile, Tussah silk, or fabric with an equivalent appearance and weight.
*The one-piece sleeves are eased and tucked at the shoulder seam, and bloused to just below the elbow. The shoulder seam does not extend far past the top of the shoulder and onto the upper arm.
*On the forearm, the sleeve is pleated and quilted in approximately one inch sections for a tailored fit to the arm, and extends to the wrist.
*As with the Base Tunic, the side seams are open from the waist down, resulting in two different sections:
**The lower panel formed in the rear is cut on a circle which extends to mid-thigh.
**The front panels (two) extend to below the knees and are cut straight across the bottom.
*Attached at the waist are two additional narrow panels (on top of the front panels) which extend to knee level.
*The robe tapers towards waist level to close; actual closure is hidden by the belt.
*''(Allowed, but not recommended): The two narrow panels may be attached to the belt in the same manner as the loin cloth.''|
*The lower panel formed in the rear should overlap the front panels slightly around waist level.
*The front panels (not the narrow ones) should extend to the top of the boot.
*The two narrow panels should be made of the same material as the Tabard.
*The sleeves should have pleats at the shoulders.|}}

{{CRLtemplate-onelevel|File:SL_maul_tabbards.jpeg|Tabard|
*Worn over the Sith Robe, is black crinkle/boiled silk or fabric with an equivalent appearance and weight, and wraps around the neck.
*Approximately five and one half inches wide, extend to mid-thigh, and secured in place by the belt.
*Both ends extend straight down (they do not cross over each other).|
*The tabard should not overlap onto the Base Tunic collar.
*It should be positioned such that the loin cloth overlaps approximately half of each end of the Tabard.|}}

{{CRLtemplate-onelevel|File:SL_maul_gloves.jpeg|Gloves|
*Made of black leather or leather-like material in a matte finish.
*Must be devoid of any distinctive stitching.
*The cuff extends to approximately mid-forearm length in a gauntlet fashion.|
*The gloves should be leather.|}}

{{CRLtemplate-onelevel|File:SL_maul_belt.jpeg|Belt|
*Black leather or leather-like material constructed in two pieces:
*The wider belt is approximately five inches wide in the center (front), and it tapers at the sides/hips to approximately three inches. It fastens in the back with Velcro hidden under a square belt keeper of the same material.
*Over this wider belt are four, three-quarter inch, strips which are anchored with black rivets which are located slightly forward of the sides/hips.
*The belt covers the closure of the Sith Robe and the starting point of the two narrow panels on the Robe, as it is worn at waist level.|
*The belt should be leather.|}}

{{CRLtemplate-nolevels|File:SL_maul_loincloth.jpeg|Loin Cloth|
*Attached under the belt, and is composed of the same material as the Tabard.
*This hanging is centered under the belt and tapers outward with a slight bow along the bottom edge.
*The loin cloth extends to the knees.||}}

{{CRLtemplate-nolevels|File:Lightsaberclip.jpg|Lightsaber Clip|
*A rectangular Covertec clip as seen in the picture is present to secure the lightsaber.
*It is attached to the belt on the wearer's right hip.
*The Hasbro or circular/oval Covertec clips will not be approved.|
*The clip should be placed on the leather stripe that is second from the bottom.|}}

{{CRLtemplate-onelevel|File:SL_maul_saber.jpeg|Dual-bladed lightsaber|
*The lightsaber should be a Master Replicas, Hasbro, or a custom built designed to match the lightsaber in TPM.
*Each half is identical, and the red knobs are all in line with each other.
*It has a machined aluminum finish.
*Other details resemble that shown in the picture (four red knobs, machined pattern, tapering to the emitters, etc.)
*The lightsaber should only be required as long as it's in compliance with the applicant’s local laws.
*''(Allowed): The lightsaber may have a chrome or polished nickel finish.''|
*The lightsaber should be capable of being belt worn (detachable blade or no blade).
*The lightsaber should be a 1:1 scale of the lightsaber used in the film.
*There should be only one device on the underside used to mount the lightsaber into the *Covertech clip; not one on each end.|}}

{{CRLtemplate-nolevels|File:SL_maul_trousers.jpeg|Trousers|
*Made from a black fabric similar to that of the Base Tunic.
*They are baggy to allow for blousing around the knees.||}}

{{CRLtemplate|File:SL_maul_boots.jpeg|Boots|
*Black leather or leather-like material, mid-calf height, and resemble a motor cross styled boot (lace-less and black colored zippers if any are present).
*Has a double “V” stitched onto the top section of the boot.
*There is a part of the boot that acts as a protector and grip that wraps onto the the toe section of the boot from the inside.
*Any silver/reflective areas of the boot must be blacked out.
*Any logos or brands that appear on stock boots must be covered by a similar material of which the boots are constructed.|
*The boots should be leather.
*Frank Thomas models Voyager, Apollo, or Tempest (slightly modified to meet the above guidelines) or custom boots designed as the ones shown in the picture are ideal.|
*The actual model used in the movie was the Frank Thomas Titan Touring Boot 101.}}

{{CRLtemplate-nolevels|File:Blankwhite.gif|Summary of Various Layers and Lengths from Above|

*From inner layers to outer layers:
**Layer 1: Base Tunic and Pants
**Layer 2: Sith Robe
**Layer 3: Narrow Front Panels sewn onto Sith Robe
**Layer 4: Tabards
**Layer 5: Belt and Loin Cloth

*From longest to shortest:
**Garment extending ''below knee level'': Main Front Panels of the Sith Robe
**Garments at or around ''knee level'': Loin Cloth & Narrow Front Panels sewn onto Sith Robe
**Garment just ''above knee level'': Base Tunic
**Garments extending to ''mid-thigh level'': Rear Panel of Sith Robe & Tabards||}}

{{CRLaccessories}}

{{CRLtemplate-nolevels|File:Blankwhite.gif|Hooded Robe|
* The hood, yoke, and sleeves are made of black wool or an equivalent fabric.
* The body of the robe can be of black silk, linen, cotton or a comparable fabric in weave, weight and appearance.
* The hood is large and falls down the back without coming to a point.
* Belled sleeves end at the elbows.
* In front, the yoke angles down from the shoulders, coming to a point at the bottom of the sternum.
* The robe body is pleated in a sunray pattern (i.e. the pleats become narrower at the top than the bottom), and falls to within 1 inch of the floor.
* The pleats are ironed, not sewn in place.||}}

{{CRLfooter|SLD_CRL|S}}

Template:CRLcommpad

2013-06-12T21:33:49Z

Muppet:

{{CRLtemplate|File:Generic-commpad.jpg|Imperial Communications Pad|
* Rectangular communications pad, with buttons and detailing as shown, on a grey or silver background. |
* Compads shall not be electronically lit. |
* Rectangular communications pad, with buttons and detailing as shown, on a white background. }}

Costuming:TK deathtrooper

2013-06-10T08:40:47Z

Muppet:

{{CRLheader|Death Trooper|File:TK_deathtrooper-full.jpg|TK-7602|Brian Anderson}}

{{CRLdetinfo|1116|Death Trooper|TK|Star Wars Expanded Universe|The Death Troopers were introduced in a Star Wars Expanded Universe novel of the same name. The book follows the classic zombie outbreak story, but set on a Star Destroyer. The Death Troopers were later used in Star Wars Galaxies and represented by Gentle Giant as a bust.

Please note that this particular costume may not be welcome at all 501st events. This is not recommended as a primary Legion membership costume. Please contact your garrison CO/GML with any questions if you are planning to create one.}}

{{CRLfisdlevels}}

{{CRLlmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:TK_deathtrooper_helmet.jpg|Helmet|

*Shall have a distressed/cracked/damaged look. If any large areas are missing from the helmet and skin is exposed it shall with be covered with zombie-like prosthetic skin.
*Should have stains to emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Should be aged white with some areas having a drab olive greenish and yellowed tint.
*Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray.
*Rear traps and tears have vertical black lines.
*Lenses are flat material, green in color, sufficiently dark enough to obscure the costumer's eyes.
*The “ear” bars have three or four bumps and should be gray or painted gray, with a black outline. Painting the bumps with rank stripes (highlighted) in black is optional.
*Frown is painted gray and does not leave the teeth area. Eight total teeth on the frown are cut out.
*Tube stripes are medium blue, numbering between 9 and 16 per side with the curve bends extending backwards.
*Vocoder (vertically ribbed chin detail) is painted black.
*Aerators/Hovi mix tips (cylinders on either side of the vocoder) are black or painted black.
*Tears, traps, and tube stripes may be hand painted, decals, or decals that replicate hand painted.
*Mesh may be used behind the frown to obscure the face of the wearer.
*Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
*Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary. Please visit FISD/whitearmor.net for more info on these modifications. |
*Shall have stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Shall be aged white with some areas having a drab olive greenish and yellowed tint.
*Ears shall have three screws per side, one above and one below the ear bar and one at the base of the helmet.
*Ear bars should have four bumps only, not three.
*Traps/tears and tube stripes shall have the correct ANH TK details.
*Correct 'Hovi mic' aerator tips.
*FX helmets are not allowed.
|
*MRCE and/or EFX PCR helmets are not allowed.
*ANHv2 helmets are not allowed.
*Ear bars shall have only one or two bumps painted in black (rank stripes).
*Neck trim shall be of an s-type profile rather than a u-type profile.
*Tears/traps shall be hand painted or use decals that emulate hand painted (with correct ANH TK details).

}}

{{CRLtemplate|File:Deathtrooper_neckseal.jpg|Neck Seal|
*Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to the top of the Adam's apple.
*Neck Seal shall be destressed/worn.|
*Neck Seal may have some rips/missing areas in the material. If any skin is exposed it shall be covered with zombie-like prosthetic/mask.
| }}

{{CRLtemplate|File:Deathtrooper_shoulder_straps.jpg|Shoulder Straps|
*These shall be securely mounted in front and may free float in back. They may be affixed with rivets, Velcro, or adhesive.
*No visible rivets are allowed.
*Shall have a distressed/cracked/damaged look.
*Should be aged white with some areas having a drab olive greenish and yellowed tint.
*May have stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*One Shoulder Strap maybe omitted from this costume (either left or right but not both) If a Shoulder Strap is omitted, then it should be replaced/tied with *Worn/old looking mummy style bandages to help hold the chest and back together.|
*Shall be aged white with some areas having a drab olive greenish and yellowed tint.|
*These shall free float in back.
*These shall be glued in front.
*The plastic shoulder straps need to be held down in the back via a white elastic band to the white fabric that connects/bridges the chest and back piece.}}

{{CRLtemplate|File:TK_deathtrooper-shoulders.jpg|Shoulder Bells|
*One on each shoulder. The shoulder bells are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders and should have a black elastic strap that wraps around the inside of the bicep.
*Shall have a distressed/cracked/damaged look.
*May have some stains that emulate dried blood, Liquid / permanently wet fake blood is not allowed.
*Should aged white with some areas having a drab olive greenish and yellowed tint. |
*Shall be aged white with some areas having a drab olive greenish and yellowed tint|
}}

{{CRLtemplate|File:TK_deathtrooper-bicep.jpg|Biceps|
*Biceps are fully closed.
*Shall have a distressed/cracked/damaged look.
*One bicep may be omitted from the costume (either left or right but not both).
*May have some stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Should be aged white with some areas having a drab olive greenish and yellowed tint. |

*Shall be aged white with some areas having a drab olive greenish and yellowed tint. |
}}

{{CRLtemplate|File:TK_deathtrooper-forearms.jpg|Forearms|
*Forearms are fully closed.
*Shall have a distressed/cracked/damaged look.
*May have some stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Should be aged white with some areas having a drab olive greenish and yellowed tint.|
*Should have some stains that emulate dried blood, Liquid / permanently wet fake blood is not allowed.
*Shall be aged white with some areas having a drab olive greenish and yellowed tint.|
*No return edge on the inside of the front of the forearm is allowed.
}}

{{CRLtemplate|File:Deathtrooper_handplates.jpg|Hand Plates|
*Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material.
*Shall have a distressed/cracked/damaged look.
*One Hand Plate may be omitted from the costume (either left or right but not both).
*May have some stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Should be aged white with some areas having a drab olive greenish and yellowed tint. |
*Should have some stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Shall be aged white with some areas having a drab olive greenish and yellowed tint.|
*Hand guards shall be latex or latex-like, painted white, affixed to rubber gloves in lieu of plastic hand guards.
}}

{{CRLtemplate|File:Deathtrooper_gloves.jpg|Gloves|
* Black in color, made of either rubber, nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured.
*Gloves shall be distressed/worn. If any skin is exposed it shall be covered with a zombie-like prosthetic skin.| |
*Gloves shall be rubber or rubber-like chemical gloves, in black. }}

{{CRLtemplate|File:TK_deathtrooper-chest.jpg|Chest|
*Chest plate overlaps the abdominal plate.
*Shall have a distressed/cracked/damaged look.
*Should have stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Should be aged white with some areas having a drab olive greenish and yellowed tint.
*Chest plate may have one of the top corner/shoulder strap areas missing. If you are opting to damage/remove this area of the chest plate, then you should strap the remaining area with Worn/old looking mummy style bandages to help hold the chest and back together.
*May have blaster wounds.|
*Shall have stains that emulate dried blood, Liquid / permanently wet fake blood is not allowed.
*Shall be aged white with some areas having a drab olive greenish and yellowed tint.|
*Chest and back shall be connected with a white fabric or preferably elastic strap at the shoulders.
*Ideally the AM/FX style chest plate should be replaced with a more screen accurate type. If using an AM/FX style chest plate, the bottom and sides shall be trimmed and a new return edge shall be added at the bottom to eliminate the over elongated appearance and to give a more accurate look. See the tutorial: http://www.whitearmor.net/fisd/Tutorial-chestback
}}

{{CRLtemplate|File:TK_deathtrooper_back.jpg|Back|
*Back plate contains a "O II" design.
*Shall have a distressed/cracked/damaged look.
*May have a few stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Should be aged white with some areas having a drab olive greenish and yellowed tint. |
*Shall be aged white with some areas having a drab olive greenish and yellowed tint.
*Back plate may have one of the top corners/shoulder strap areas missing. If you are opting to damage/remove this area of the back plate, then you should strap the remaining area with Worn/old looking mummy style bandages to help hold the chest and back together.|
*Back plate shall have no, or minimal overlap of the kidney plate.
*Ideally the AM/FX style back plate should be replaced with a more screen accurate type. If using an AM/FX style back plate it shall have no, or minimal overlap of the kidney plate. and shall be reshaped to emulate a screen used back plate by properly trimming and re-shaping (stretching) the left and right edges of the armor to contour to your body. Note: There is currently no tutorial available for this, but you can see an example of this Mod and visual comparison at whitearmor.net
}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
*Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs.
*Under Suit shall be distressed/worn.|
*The under suit may have some rips/missing areas in the material. If any skin is exposed it shall with be covered with zombie-like prosthetic skin.
*Some area of the Under Suit should have Worn/old looking mummy style bandages. | }}

{{CRLtemplate|File:Deathtrooper_abplate.jpg|Abdomen Plate|
*The ab plate has a button area that matches the color pattern shown (3 blue + 6 gray); buttons are approximately 7/16" (11mm) in diameter.
*Shall have a distressed/cracked/damaged look.
*Should have stains that emulate dried blood, but shall not use liquid / permanently wet fake blood.
*Should be an aged white with some areas having a drab olive greenish and yellowed tint. |
*Any gap between the ab and kidney plate shall be no more than 1/2" (12.5mm) wide. Any shims used to achieve this effect should be of a similar material and color as the ab and kidney plate. Shims shall fit flush and seams are allowed.
*Shall have stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Shall be an aged white with some areas having a drab olive greenish and yellowed tint.
*The ab plate may have large missing/broken off area/areas. If any large area is exposed it shall with be covered with zombie-like prosthetic skin.|
*Ideally there should be no gap between the ab and kidney plates, just a single visible seam line.
*Rivets on the left side of the ab plate: a total of three rivets, the heads should be approximately 5/16" (8mm) diameter and equally spaced out along the depth of the armor and about 10mm from the edge. They may be painted white, or not. Note:For the original used TK armor, this type of rivets where, bifurcated rivets or split rivet.
*A single male snap on the top right corner of the ab plate shall be present.
*A single split rivet or brad shall be present on the crotch tab of the ab plate. It does not need to be functional.
}}

{{CRLtemplate|File:TK_deathtrooper-kidney.jpg|Kidney Plate|
*A separate kidney plate shall be present, split from the butt plate.
*Shall have a distressed/cracked/damaged look.
*Should be an aged white with some areas having a drab olive greenish and yellowed tint. |
*Three rivets shall be present on the left side of the kidney plate, the heads should be approximately 5/16"(8mm) diameter and equally spaced out along the depth of the armor and about 10mm from the edge. They may be painted white, or not. Note: For the original used TK armor, this type of rivets where, bifurcated rivets or split rivet.| }}

{{CRLtemplate|File:TK_deathtrooper-butt.jpg|Butt Plate|
*Shall have a distressed/cracked/damaged look.
*Should be aged white with some areas having a drab olive greenish and yellowed tint.
*A separate butt plate is required, split from the kidney plate.
*Shall be an aged white with some areas having a drab olive greenish and yellowed tint.|
*Two male snaps shall be present on the crotch tab of the butt plate. They do not need to be functional.| }}

{{CRLtemplate|File:TK_deathtrooper-belt.jpg|Belt|
*Belt face is made of plastic (TK ammo belt).
*The soft belt proper is made of canvas, or material with a canvas covering. Size must be 2.75” (70 mm) to 3.25”(83 mm) wide and not wider than the plastic portion of the belt. The color is be white to off-white and shall have a distressed old look.
*The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.
*Shall have a distressed/cracked/damaged look.
*May have stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Should be aged white with some areas having a drab olive greenish and yellowed tint.|
*Shall be aged white with some areas having a drab olive greenish and yellowed tint.
*There shall be three square buttons, one centered in the middle and one on each end of the plastic ammo belt.
*One drop box may be omitted from the costume (either left or right, but not both). If opting to remove one of the drop boxes, the white strap that the drop box normally hangs from shall be ripped/torn.|
*Drop boxes are closed in the back.
*The corners of the plastic ammo belt shall be trimmed at a 45 degree angle.
}}

{{CRLtemplate|File:Deathtrooper_detanator.jpg|Thermal Detonator|
*Attaches to the back of the belt. This is a gray cylinder between 2”(50mm) and 2.5" (64mm) in diameter with white end caps on each end, and a white control panel pad, with controls closest to the right end cap.
*Shall have a distressed/cracked/damaged look.
*Should be aged white with some areas having a drab olive greenish and yellowed tint. |
*Shall be aged white with some areas having a drab olive greenish and yellowed tint. |
*The thermal detonator needs to be attached via metal clips approximately 1" (25mm) wide, and shall be all gray without silver stickers or silver paint.
}}

{{CRLtemplate|File:TK_deathtrooper_thighs.jpg|Thighs|
*Thigh armor shall be closed in the back.
*The small ammo belt is installed on the bottom of the right thigh.
*Shall have a distressed/cracked/damaged look.
*May have stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Should be aged white with some areas having a drab olive greenish and yellowed tint.|
*Should have some stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Shall be aged white with some areas having a drab olive greenish and yellowed tint.|
*The thigh ammo belt shall be connected by brads/split rivets only – but not by standard rivets.
*The bottom corners of the thigh ammo belt shall be rounded off. }}

{{CRLtemplate|File:TK_deathtrooper-shins.jpg|Lower Legs|
*Greaves close in the back. The trapezoid knee plate (sniper knee plate) is affixed to the left greave and may have two visible brads or rivets securing it to the greave.
*The AM greaves (shins) shall be on the proper legs, with a new cover strip. The cover strip edge shall be facing the inside of the leg. Note: There is a manufacturer defect with the AM greaves (shins) that may cause you to wear the them improperly. Please see the Tutorial titled :"AM armor shins: the proper way to assemble and wear", on the whitearmor.net
*Shall have a distressed/cracked/damaged look.
*May have stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Should be aged white with some areas having a drab olive greenish and yellowed tint. |
*Should have some stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Shall be aged white with some areas having a drab olive greenish and yellowed tint.|
*There should be no visible rivets or brads used to secure the sniper plate to the left greave.

}}

{{CRLtemplate|File:Deathtrooper_boots.jpg|Boots|
*White leather or leather-like, above ankle height, with a flat sole with a short heel, and small U-shaped elastic sections on both sides of the ankle with no buckles or laces. Jodhpur/Chelsea-type boots or an equivalent style is acceptable. Elvis or Mariachi boots are not allowed.
*Shall have a distressed/cracked/damaged look.
*May have some stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Should be aged white with some areas having a drab olive greenish and yellowed tint. |
*Should have some stains that emulate dried blood. Liquid / permanently wet fake blood is not allowed.
*Shall be aged white with some areas having a drab olive greenish and yellowed tint.|
*There shall be no seam on the front of the boot (e.g. CABoots are not allowed). }}

{{CRLaccessories}}

{{CRLtemplate|File:TK_anh_stunt_holster.jpeg|Holster|
*Holster may be omitted from the costume. If a holster is worn, it will be made of black leather or leather-like material. Worn on the left side of belt and be attached from behind, with no loops covering the outside of the belt. The holster will be affixed with two fasteners at the bottom of the belt instead of none or four. The fasteners may be rivets, snaps, or Chicago screws.|| }}

{{CRLtemplate|File:Uc28616BVIII.gif|Mummy style bandages|
*It is optional to have some Worn/old looking (mummy style) bandages. The mummy style bandages may be wrapped loosely around some areas of the costume, but not over 30%. | | }}

{{CRLtemplate|File:Zombie parts.jpg|Zombie prosthetic|
*May be a latex or latex like Halloween mask, hands or body parts. | |
*Shall be profressional movie-like makeup }}

{{CRLtemplate|File:TK_rotj_e11.jpg|BlasTech E-11|
*Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.|
*Folding stock (does not need to function).
*No ammo counter shall be present.
*D-ring mounted on the rear.
*Correct style scope.
*No power cylinders on the magazine housing.
*Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 7 U shaped channels on blaster (all holes on barrel shall be covered).
*If using the popular commercially available Stormtrooper blasters, you shall grind off the T-tracks and replace them with U shaped channels and cover the open rows of holes (total of 7 U shaped channels in all).
*Correct greeblies on the left rear area shall be present (door catch and two "hammers").|
*Hasbro blasters are not allowed, even conversions.
*Forward D-ring shall be mounted underneath the front sight on the left side of the barrel.
*Use of the correct front sight (which differs from ANH and ESB).
*The scope rail is unique to ROTJ E11 and is not like the normal open ANH/ESB scope rails, but is a solid, one piece, with a unique sight design on the front. The scope connects to the notched out area of the solid rail. The scope shall be the correct design (as the ones seen in ROTJ), and shall attach to the scope rail via one scope mount.
*The muzzle will be unlike the normal ANH style. It shall be flat with two counter sunk Allen bolts (one located at the four o’clock position and one located at the ten ‘o’clock position).
*The door catch shall be correct, not a "close enough" attempt as seen on the Cinemastery blaster.
}}

{{CRLtemplate|File:TK_anh_stunt_dlt19.jpeg|BlasTech DLT-19 Heavy Blaster Rifle|
*Based on a real or replica MG-34 machine gun. |
*A DLT-19 is an MG-34 with T-tracks on the barrel, ejection port cover added, and a small disk on left side.| }}

{{CRLfooter|FISD_CRL|T}}

File:Deathtrooper abplate.jpg

2013-06-10T08:38:28Z

Muppet:

File:Deathtrooper shoulder straps.jpg

2013-06-10T08:30:31Z

Muppet:

File:Deathtrooper neckseal.jpg

2013-06-10T08:30:30Z

Muppet:

File:Deathtrooper handplates.jpg

2013-06-10T08:30:30Z

Muppet:

File:Deathtrooper gloves.jpg

2013-06-10T08:30:30Z

Muppet:

File:Deathtrooper detanator.jpg

2013-06-10T08:30:30Z

Muppet:

File:Deathtrooper boots.jpg

2013-06-10T08:30:30Z

Muppet:

Costuming:TX magmatrooper

2013-06-10T02:24:17Z

Muppet:

{{CRLheader|Magma Trooper|File:TX_magma_full.jpg‎ |TX-9293 |Thomas E Durbin }}

{{CRLdetinfo| 1113 |Magma Trooper|TX|The New Essenial Guide to Weapons and Technology; Star Wars: The Visual Dictionary | }}

{|style="background-color:#ffffff; text-align:left" width="100%" cellspacing="10"
|-
|
Black text indicates a feature that is required for approval. Blue text denotes features that are nice to have, but not required. Red text indicates features that take the prop/costume item to an even higher level of accuracy.

'''For 501st membership only the requirements listed in black need to be met.'''

'''Special Notes:'''

*The armor parts shall be gloss red and made from one of these types of materials or like materials: Fiberglass, ABS (Acrylonitrile Butadiene Styrene), or HIPS (High Impact Polystyrene).

* Blasters are not required for legion membership per our [[Weapons_policy|weapons policy]].

|-
|align="center" colspan=2|<hr width="90%">
|}

{{CRLlmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:TX_magma_helmet.jpg|Helmet|
* Lenses must be Black, Smoke or dark green and dark enough to obscure the costumer's eyes. They may be flat or Bubble.
* The grey "ears" have three or four bumps
* Frown must have either 6 or 8 teeth cut out and Grey coloring must not leave indented area.
* Tube stripes are black and may number between 9 and 15 per side with the curve bends extending backwards. There does not need to be the same number per side.
* Aerators (cylinders on either side of the vocoder) are black, and screening is silver.
* Tears and traps may be: hand painted, decals, or decals that replicate hand painting. They must be grey with black outlines and highlights.
* Chin / Vocoder (vertically ribbed chin detail) is black.
*Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
*Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary.
||}}

{{CRL_generic_tk_neckseal}}

{{CRLtemplate|File:TX_magma_shoulderstraps.jpg|Shoulder Straps|
* These must be securely mounted in front and may free float in back.||}}

{{CRLtemplate|File:TX_magma_shoulderbells.jpg|Shoulder Bells|
* One on each shoulder. The shoulder bells are considered effectively symmetrical; they may worn interchangeably on the left and right shoulders.||}}

{{CRLtemplate|File:TX_magma_biceps.jpg|Biceps|
* Biceps are fully closed.||}}

{{CRLtemplate|File:TX_magma_forearms.jpg|Forearms|
* Forearms must appear to be fully sealed and enclosed.||}}

{{CRLtemplate|File:TX_magma_handplates.jpg|Handplates|
* Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material.||}}

{{CRL_generic_tk_gloves}}

{{CRLtemplate|File:TX_magma_chest.jpg|Chest Plate|
* Chest plate overlaps the abdominal plate.||}}

{{CRLtemplate|File:TX_magma_back.jpg|Back Plate|
* Back plate contains a "O II" design with little or no overlap of the kidney plate.||}}

{{CRLtemplate|File:TX_magma_ab.jpg|Abdominal Plate|
* The ab plate has a button area that has 9 gloss buttons of approximately 7/16" in diameter.
* Six of the buttons are black, the other three are grey, as shown.||}}

{{CRLtemplate|File:TX_magma_back-butt.jpg|Kidney and Butt Plates|
* It is allowable to have a single kidney/butt plate for 501st requirements.
* If a separate kidney plate is used, it should line up with the ab plate, with the top of the kidney plate being flush to or under the back plate.
* If a separate butt plate is used, it should line up below the bottom of the belt with with the ab plate, with minimal gap between it and the kidney plate.||}}

{{CRLtemplate|File:TX_magma_belt.jpg|Belt|
* Belt face is made of plastic (ammo belt). It is comprised of 6 rectangular boxes, with three square buttons, one centered in the middle and one on each end.
* Belt proper may be made from glossy red ABS or a similar shiny material and must be 3 to 3.5" wide. Red canvas or similar heavy material may also be used.
* The drop boxes dangle from the sides of the plastic belt face via black straps and are aligned under the plastic tabs of the ammo belt. They may be red or black in color.||}}

{{CRLtemplate|File:TX_magma_thermal.jpg|Thermal Detonator|
* (a.k.a. O2 canister) attaches to the back of the belt. This is a grey cylinder 2 to 2.5" in diameter with red end caps and a red control panel pad, with controls closest to the right end cap.||}}

{{CRLtemplate|File:TX_magma_thighs.jpg|Thigh Armor|
* The thigh armor may open and firmly close in the back allowing the two halves to appear sealed when viewed by spectators. The ammo belt is installed on the bottom of the right thigh.||}}

{{CRLtemplate|File:TX_magma_shins.jpg|Shin Armor|
* The shin armor is able to open and firmly close in the back allowing the two halves to appear sealed when viewed by spectators. The trapezoid knee plate is affixed to the top of the left shin.||}}

{{CRLtemplate|File:TX_magma_boots.jpg|Boots|
* Red leather or leather-like, above ankle height, with a flat sole, and small U-shaped elastic sections on both sides of the ankle with no buckles or laces. Jodphur-type boots or an equivalent style. All stitching must be red, and unnecessary or decorative stitching must not be present. Elvis / Mariachi boots are not acceptable.
* White, or other color boots may be painted red so long as the boots are maintained to remain the proper color.||}}

{{CRLtemplate|File:TX_shadowstorm_holster.jpeg|Holster|
*Made of black leather or leather-like material.
*Holster must be worn on the left and be may be attached to the belt from behind with rivets or with loops covering the outside of the belt.||}}

{{CRLaccessories}}

{{CRLblackpauldron}}

{{CRLgeneric-e11}}

{{CRLfooter|Specops_CRL|T}}

Costuming:TX novatrooper elite

2013-06-10T02:23:11Z

Muppet:

{{CRLheader|Novatrooper, Elite|File:Tx_Nova_elite_full.jpg | TX-5992 | Melinda Cabello }}

{{CRLdetinfo| 1113 |Novatrooper, Elite|TX|Star Wars Galaxies TCG: Champions of the Force | }}
{|style="background-color:#ffffff; text-align:left" width="100%" cellspacing="10"
|-
|
Black text indicates a feature that is required for approval. Blue text denotes features that are nice to have, but not required. Red text indicates features that take the prop/costume item to an even higher level of accuracy.

'''For 501st membership only the requirements listed in black need to be met.'''

'''Special Notes:'''

*The armor parts shall be gloss black and made from one of these types of materials or like materials: Fiberglass, ABS (Acrylonitrile Butadiene Styrene), or HIPS (High Impact Polystyrene).

*All striping "flash" is clean and unweathered.

* Blasters are not required for legion membership per our [[Weapons_policy|weapons policy]].

|-
|align="center" colspan=2|<hr width="90%">
|}

{{CRLlmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Tx_nova_elite_bucket.jpg‎|Helmet|
* Lenses must be sufficiently dark enough to obscure the costumer's eyes. They may be flat or bubbled. Acceptable colors are: black, smoke, or dark green.
* The "ear" bars have three or four bumps and may be left the same color as the body or painted flat black.
* The frown must have either 6 or 8 teeth cut out. If there are spaces between the teeth the wearer's face must not be seen.
* The tube stripes are black in color and may number between 9 and 15 per side with the curve bends extending backwards. These may be hand painted or decals. There does not need to be the same number per side.
* The aerators (cylinders on either side of the vocoder) are black, and screening maybe silver or black.
* Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are solid black.
* Helmet flash is a single gold vertical stripe the fitting between the lenses that runs from the top of the chin to the back of the crown and does not enter the teeth area. A gold bar must also sit under the tube stripes on each side.
*Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
*Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary.
||}}

{{CRL_generic_tk_neckseal}}

{{CRL_tx_stormtrooper_shoulderstraps}}

{{CRLtemplate|File:TX_nova_shoulderbells.jpg|Shoulder Bells|
*One on each shoulder with a gold vertical stripe running down the center of the outside. The shoulder bells are considered effectively symmetrical; they may worn interchangeably on the left and right shoulders.||}}

{{CRLtemplate|File:TX_nova_biceps.jpg|Biceps|
* Biceps are fully closed with a gold vertical stripe running down the center of the outside.||}}

{{CRLtemplate|File:TX_nova_forearms.jpg|Forearms|
* Forearms are fully closed with a gold vertical stripe running down the center of the outside.||}}

{{CRLtemplate|File:TX_nova_handplates.jpg|Handplates|
* Roughly pentagonal in shape, the hand plates are gold and are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material.||}}

{{CRL_generic_tk_gloves}}

{{CRL_tx_stormtrooper_chest}}

{{CRL_tx_stormtrooper_back}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos. | | }}

{{CRL_tx_stormtrooper_ab}}

{{CRL_tx_stormtrooper_kidney}}

{{CRL_tx_stormtrooper_butt}}

{{CRLtemplate|File:TX_nova_elite_belt.jpg|Belt|
* Belt face is made of plastic (ammo belt). It is comprised of 6 rectangular boxes, with three square buttons, one centered in the middle and one on each end.
* Belt proper may be made from glossy black ABS or a similar shiny material and must be 3 to 3.5" wide. Black canvas or similar heavy material may also be used.
* Drop boxes (small rectangular parts attached seen hanging from Stormtrooper belts, above the thigh.) holster and thermal detonator must not be worn.||}}

{{CRL_tx_stormtrooper_thighs}}

{{CRLtemplate|File:TX_nova_shins.jpg|Shin Armor|
* The shin armor is able to open and firmly close in the back allowing the two halves to appear sealed when viewed by spectators. The trapezoid knee plate is affixed to the top of the left lower leg piece. The hexagon in the center and upper ridge of the knee plate as well as its top trim must be gold.||}}

{{CRL_tx_stormtrooper_boots}}

{{CRLtemplate|File:TX_gold_pauldron.jpg‎|Gold Pauldron|
* Must be gold in color and made from vinyl or leather. Must be worn over the right shoulder.||}}

{{CRLtemplate|File:TX_nova_elite_pouch.jpg|Ammo Pouches|
*Black in color, made of canvas, leather or leather-like German MP-40 style ammo pouches. There shall be two minimum: one pouch on the left shoulder and one on the right hip.
* A rectangular black leather "roadblock" pouch may be substituted for the MP-40 styled right hip pouch. | |}}

{{CRLtemplate|File:TX_nova_backpack.jpg‎|Field Backpack|
* Solid black in color and styled after the ANH Sandtrooper packs.
* A loose interpretation is allowed, but screen accuracy is encouraged.||}}

{{CRLaccessories}}

{{CRL-dlt19}}

{{CRL-rt97}}

{{CRL-t21}}

{{CRLfooter|Specops_CRL|T}}

Costuming:TX novatrooper medic

2013-06-10T02:22:12Z

Muppet:

{{CRLheader|Novatrooper Medic|File:TX_nova_medic_fullbody.jpg |TX-5036 |Ty C. Graham }}

{{CRLdetinfo| 1113 |Novatrooper Medic|TX|Star Wars Galaxies (PC Game) | }}

{|style="background-color:#ffffff; text-align:left" width="100%" cellspacing="10"
|-
|
Black text indicates a feature that is required for approval. Blue text denotes features that are nice to have, but not required. Red text indicates features that take the prop/costume item to an even higher level of accuracy.

'''For 501st membership only the requirements listed in black need to be met.'''

'''Special Notes:'''

* The armor parts shall be gloss black and made from one of these types of materials or like materials: Fiberglass, ABS (Acrylonitrile Butadiene Styrene), or HIPS (High Impact Polystyrene).

*All striping "flash" is clean and unweathered.

* The Novatrooper Medic red has been identified as Kirsch Red from Sherwin Williams: SW6313. RGB Value: R-154 | G-70 | B-80. Pantone code: 696c.

* Blasters are not required for legion membership per our [[Weapons_policy|weapons policy]].

|-
|align="center" colspan=2|<hr width="90%">
|}

{{CRLlmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:TX_nova_medic_helmet.jpg‎|Helmet|
* Lenses must be sufficiently dark enough to obscure the costumer's eyes. They may be flat or bubbled. Acceptable colors are: black, smoke or dark green.
* The "ear" bars have three or four bumps and may be left the same color as the body or painted flat black.
* The frown must have either 6 or 8 teeth cut out. If there are spaces between the teeth the wearer's face must not be seen.
* The tube stripes are black in color and may number between 9 and 15 per side with the curve bends extending backwards. These may be hand painted or decals. There does not need to be the same number per side.
* The aerators (cylinders on either side of the vocoder) are black, and screening maybe silver or black.
* Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are solid black.
* Helmet flash is a light red stripe that runs horizontally along the brow with thicker sections cut at a right angle near the temple traps. Another horizontal light red stripe runs between the rear dome traps and are about half the height of the traps. Light red bars must also sit under the tube stripes on each side.
*Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
*Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary.
||}}

{{CRL_generic_tk_neckseal}}

{{CRL_tx_stormtrooper_shoulderstraps}}

{{CRLtemplate|File:TX_nova_medic_shoulderbells.jpg|Shoulder Bells|
*One on each shoulder with a light red vertical stripe running down the center of the outside. The shoulder bells are considered effectively symmetrical; they may worn interchangeably on the left and right shoulders.||}}

{{CRLtemplate|File:TX_nova_medic_biceps.jpg|Biceps|
* Biceps are fully closed with a light red vertical stripe running down the center of the outside.||}}

{{CRLtemplate|File:TX_nova_medic_forearms.jpg|Forearms|
* Forearms are fully closed with a light red vertical stripe running down the center of the outside.||}}

{{CRLtemplate|File:TX_nova_medic_handplates.jpg|Handplates|
* Roughly pentagonal in shape, the hand plates are light red and are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material.||}}

{{CRL_generic_tk_gloves}}

{{CRL_tx_stormtrooper_chest}}

{{CRL_tx_stormtrooper_back}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos. | | }}

{{CRL_tx_stormtrooper_ab}}

{{CRL_tx_stormtrooper_kidney}}

{{CRL_tx_stormtrooper_butt}}

{{CRL_tx_stormtrooper_belt}}

{{CRL_tx_stormtrooper_detonator}}

{{CRL_tx_stormtrooper_thighs}}

{{CRLtemplate|File:TX_nova_medic_shins.jpg|Shin Armor|
* The shin armor is able to open and firmly close in the back allowing the two halves to appear sealed when viewed by spectators. The trapezoid knee plate is affixed to the top of the left lower leg piece. The hexagon in the center and upper ridge of the knee plate as well as its top trim must be light red.||}}

{{CRL_tx_stormtrooper_boots}}

{{CRLaccessories}}

{{CRL_tx_stormtrooper_holster}}

{{CRLgeneric-e11}}

{{CRLfooter|Specops_CRL|T}}

Template:CRL tx stormtrooper helmet

2013-06-10T02:20:40Z

Muppet:

{{CRLtemplate-nolevels|File:TX_shadowstorm_helmet.jpeg|Helmet|
* Lenses must be sufficiently dark enough to obscure the costumer's eyes. They may be flat or bubbled. Acceptable colors are: black, smoke, dark green, or silver.
* The body of the "ears" may be black or gray. The bars have three or four bumps and may be left the same color as the body or painted black.
* The frown must have either 6 or 8 teeth cut out and any coloring must not leave the indented area. Acceptable colors are: black, gray or silver. If there are spaces between the teeth the wearer's face must not be seen
* The tube stripes are black in color and may number between 9 and 15 per side with the curve bends extending backwards. These may be hand painted or decals. There does not need to be the same number per side.
* Vocoder (vertically ribbed chin detail) may be black or silver.
* The aerators (cylinders on either side of the vocoder) are black, and screening maybe silver or black.
* Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) may be: hand painted, decals. Acceptable colors are: black or gray. Rear traps and tears may have vertical black lines.
*Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
*Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary.
||}}

Costuming:TX novatrooper

2013-06-10T02:10:59Z

Muppet:

{{CRLheader|Novatrooper|File:Nova_full.jpg‎ |TX-3409 Adam Lochowicz | }}

{{CRLdetinfo| 1113 |Novatrooper|TX|Star Wars Galaxies (PC Game) | }}

{|style="background-color:#ffffff; text-align:left" width="100%" cellspacing="10"
|-
|
Black text indicates a feature that is required for approval. Blue text denotes features that are nice to have, but not required. Red text indicates features that take the prop/costume item to an even higher level of accuracy.

'''For 501st membership only the requirements listed in black need to be met.'''

'''Special Notes:'''

*The armor parts shall be gloss black and made from one of these types of materials or like materials: Fiberglass, ABS (Acrylonitrile Butadiene Styrene), or HIPS (High Impact Polystyrene).

*All striping "flash" is clean and unweathered.

* Blasters are not required for legion membership per our [[Weapons_policy|weapons policy]].

|-
|align="center" colspan=2|<hr width="90%">
|}

{{CRLgmlapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Tx_nova_helmet.jpg|Helmet|
* Lenses must be sufficiently dark enough to obscure the costumer's eyes. They may be flat or bubbled. Acceptable colors are: black, smoke, or dark green.
* The "ear" bars have three or four bumps and may be left the same color as the body or painted flat black.
* The frown must have either 6 or 8 teeth cut out. If there are spaces between the teeth the wearer's face must not be seen.
* The tube stripes are black in color and may number between 9 and 15 per side with the curve bends extending backwards. These may be hand painted or decals. There does not need to be the same number per side.
* The aerators (cylinders on either side of the vocoder) are black, and screening maybe silver or black.
* Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are solid black.
* Helmet flash is a gold stripe that runs horizontally along the brow with thicker sections cut at a right angle near the temple traps. Another horizontal gold stripe runs between the rear dome traps and is between half and three quarters the height of the traps. Gold bars must also sit under the tube stripes on each side.
*Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
*Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary.
||}}

{{CRL_generic_tk_neckseal}}

{{CRL_tx_stormtrooper_shoulderstraps}}

{{CRLtemplate|File:TX_nova_shoulderbells.jpg|Shoulder Bells|
*One on each shoulder with a gold vertical stripe running down the center of the outside. The shoulder bells are considered effectively symmetrical; they may worn interchangeably on the left and right shoulders.||}}

{{CRLtemplate|File:TX_nova_biceps.jpg|Biceps|
* Biceps are fully closed with a gold vertical stripe running down the center of the outside.||}}

{{CRLtemplate|File:TX_nova_forearms.jpg|Forearms|
* Forearms are fully closed with a gold vertical stripe running down the center of the outside.||}}

{{CRLtemplate|File:TX_nova_handplates.jpg|Handplates|
* Roughly pentagonal in shape, the hand plates are gold and are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material.||}}

{{CRL_generic_tk_gloves}}

{{CRL_tx_stormtrooper_chest}}

{{CRL_tx_stormtrooper_back}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos. | | }}

{{CRL_tx_stormtrooper_ab}}

{{CRL_tx_stormtrooper_kidney}}

{{CRL_tx_stormtrooper_butt}}

{{CRL_tx_stormtrooper_belt}}

{{CRL_tx_stormtrooper_detonator}}

{{CRL_tx_stormtrooper_thighs}}

{{CRLtemplate|File:TX_nova_shins.jpg|Shin Armor|
* The shin armor is able to open and firmly close in the back allowing the two halves to appear sealed when viewed by spectators. The trapezoid knee plate is affixed to the top of the left lower leg piece. The hexagon in the center and upper ridge of the knee plate as well as its top trim must be gold.||}}

{{CRL_tx_stormtrooper_boots}}

{{CRL_tx_stormtrooper_holster}}

{{CRLaccessories}}

{{CRLtemplate|File:TX_gold_pauldron.jpg‎|Gold Pauldron|
* Must be gold in color and made from vinyl or leather. Must be worn over the right shoulder.||}}

{{CRLgeneric-e11}}

{{CRLfooter|Specops_CRL|T}}

Costuming:TX novatrooper

2013-06-09T06:32:06Z

Muppet:

{{CRLheader|Novatrooper|File:Nova_full.jpg‎ |TX-3409 Adam Lochowicz | }}

{{CRLdetinfo| 1113 |Novatrooper|TX|Star Wars Galaxies (PC Game) | }}

{|style="background-color:#ffffff; text-align:left" width="100%" cellspacing="10"
|-
|
Black text indicates a feature that is required for approval. Blue text denotes features that are nice to have, but not required. Red text indicates features that take the prop/costume item to an even higher level of accuracy.

'''For 501st membership only the requirements listed in black need to be met.'''

'''Special Notes:'''

*The armor parts shall be gloss black and made from one of these types of materials or like materials: Fiberglass, ABS (Acrylonitrile Butadiene Styrene), or HIPS (High Impact Polystyrene).

*All striping "flash" is clean and unweathered.

* Blasters are not required for legion membership per our [[Weapons_policy|weapons policy]].

|-
|align="center" colspan=2|<hr width="90%">
|}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:Tx_nova_helmet.jpg|Helmet|
* Lenses must be sufficiently dark enough to obscure the costumer's eyes. They may be flat or bubbled. Acceptable colors are: black, smoke, or dark green.
* The "ear" bars have three or four bumps and may be left the same color as the body or painted flat black.
* The frown must have either 6 or 8 teeth cut out. If there are spaces between the teeth the wearer's face must not be seen.
* The tube stripes are black in color and may number between 9 and 15 per side with the curve bends extending backwards. These may be hand painted or decals. There does not need to be the same number per side.
* The aerators (cylinders on either side of the vocoder) are black, and screening maybe silver or black.
* Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are solid black.
* Helmet flash is a gold stripe that runs horizontally along the brow with thicker sections cut at a right angle near the temple traps. Another horizontal gold stripe runs between the rear dome traps and is between half and three quarters the height of the traps. Gold bars must also sit under the tube stripes on each side.||}}

{{CRL_generic_tk_neckseal}}

{{CRL_tx_stormtrooper_shoulderstraps}}

{{CRLtemplate|File:TX_nova_shoulderbells.jpg|Shoulder Bells|
*One on each shoulder with a gold vertical stripe running down the center of the outside. The shoulder bells are considered effectively symmetrical; they may worn interchangeably on the left and right shoulders.||}}

{{CRLtemplate|File:TX_nova_biceps.jpg|Biceps|
* Biceps are fully closed with a gold vertical stripe running down the center of the outside.||}}

{{CRLtemplate|File:TX_nova_forearms.jpg|Forearms|
* Forearms are fully closed with a gold vertical stripe running down the center of the outside.||}}

{{CRLtemplate|File:TX_nova_handplates.jpg|Handplates|
* Roughly pentagonal in shape, the hand plates are gold and are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material.||}}

{{CRL_generic_tk_gloves}}

{{CRL_tx_stormtrooper_chest}}

{{CRL_tx_stormtrooper_back}}

{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos. | | }}

{{CRL_tx_stormtrooper_ab}}

{{CRL_tx_stormtrooper_kidney}}

{{CRL_tx_stormtrooper_butt}}

{{CRL_tx_stormtrooper_belt}}

{{CRL_tx_stormtrooper_detonator}}

{{CRL_tx_stormtrooper_thighs}}

{{CRLtemplate|File:TX_nova_shins.jpg|Shin Armor|
* The shin armor is able to open and firmly close in the back allowing the two halves to appear sealed when viewed by spectators. The trapezoid knee plate is affixed to the top of the left lower leg piece. The hexagon in the center and upper ridge of the knee plate as well as its top trim must be gold.||}}

{{CRL_tx_stormtrooper_boots}}

{{CRL_tx_stormtrooper_holster}}

{{CRLaccessories}}

{{CRLtemplate|File:TX_gold_pauldron.jpg‎|Gold Pauldron|
* Must be gold in color and made from vinyl or leather. Must be worn over the right shoulder.||}}

{{CRLgeneric-e11}}

{{CRLfooter|Specops_CRL|T}}

File:Nova full.jpg

2013-06-09T06:30:06Z

Muppet:

Costuming:DZ - Tonnika Sisters - blue

2013-06-09T06:07:55Z

Muppet:

{{CRLheader|Tonikka Sisters (blue)|File:|||}}

{{CRLdetinfo| 0 |Tonikka Sisters (blue)|DZ|Star Wars Episode IV: A New Hope, There are two Tonnika Sisters. One is Green and the other is Blue. They come ideally as a ‘pair’, although the costumes can be worn individually if desired. If worn as a pair, the Shorter of the two wearers should be the Blue Tonnika Sister. | }}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:|Hair|
* Hair must be black, straight and around armpit length. This can be achieved with the wearer’s own, hair, or a wig.
* There are several small plaits that hang down the hair, starting from the top of the head.
* The top of the head has a high, domed shape, with small plaits wrapped all around it. One or two small plaits can hang slightly lower than the hairline, across the forehead.||}}

{{CRLtemplate|File:|Make Up|
*The Blue Tonnika Sister wears blue eyeshadow, and blue lipstick.||}}

{{CRLtemplate|File:Blue_tonnika_unitard.jpg|Unitard|
* The unitard style is full body, with a high neckline, to wrist to ankle. It needs to have a seam up the front, and a zip at the back, in a non shiny lycra.
* Colours is Dark Blue for the Blue Sister.||}}

{{CRLtemplate|File:Blue_tonnika_pants.jpg|Pants|
* High Cut Bikini style bottoms are worn over the unitard. They shouldn’t be too ‘brief’
* The top waistline of the pants, should go straight across, and not dip.
* Colour is Light Blue for the Blue Sister. Fabric shouldn’t be shiny.||}}

{{CRLtemplate|File:Blue_tonnika_collar.jpg|Collar and Cuffs|
* The collar is almost a triangular shape, with a point at each shoulder, and a dipped point at the front, and back.
* It has alternating panels of black, and the same fabric used to make the briefs (light blue for Blue Sister)
* Cuffs sit higher on top of the arm, and lower underneath the arm. They have a black panel on top, and the matching lighter colour blue underneath
*The collar and cuffs have a thin black edge around them.||}}

{{CRLtemplate|File:Tonnika_belt.jpg|Belt|
* Belt is black leather or leather like material , about 3-4cm / 1.25" wide.
* It has 3 clusters of 4 square metal tiles in a square, spaced 3cm / 1" apart, on either side of the buckle.
* The metal buckle has a rectangular shaped base, with a circular piece on top of it. It then has a small cube shape, that meets in a pyramid shaped point in the middle.
* It is worn straight across the top of the pants.||}}

{{CRLtemplate|File:Blue_tonnika_garter.jpg|Garter|
* A black garter, approximately 2cm / 0.75" wide is worn on the right thigh.
* It has large red stripes around it.||}}

{{CRLtemplate|File:Tonnika_boots.jpg|Boots|
* Knee High Black Boots with a low heel are worn, fitted close to the leg, with no visible buckles, laces or zips.
* Should have the appearance of leather like material.
* Glossy / Patent boots are not accepted.||}}

{{CRLfooter|No_dettachment_CRL|D}}

Costuming:Gamorrean Guard

2013-06-09T06:04:37Z

Muppet:

{{CRLheader|Gamorrean Guard|File:Gam_guard_full.jpg|DZ-77104Matt Spoljarevic |Ken Seymour|}}

{{CRLdetinfo| 1109 |Gamorrean Guard|DZ|Star Wars Episode VI: Return of the Jedi| }}

{{CRLwiplmoapproval}}

{{CRLrequirements}}

{{CRLtemplate|File:DZ_gammorean_head.jpg|Head and helmet|
* See the [[Costuming:Gamorrean_guard_head_detail|Gammorean guard head detail]] page for closeups and more angles.
* The face, arms and legs must all be the same shade of green and have the same general finish/texture.
* Lighter yellow/green shading around mouth and snout.
* Shape and proportions must match the screen used masks.
* Typically has a 'snot' like sheen in the snout and mouth areas
* Two bone coloured horns protruding from the head above the eyes and high up on the forehead
* Two larger outer and 2 smaller inner bone coloured teeth fixed and portruding upwards from the bottom of the mouth
* A appropriately detailed helmet covers the top of the head. Helmet should have a metal-like appearance.
* Leather detailing on the rear of helmet.
* A suede or coarsely woven brown scarf that hides the neckline is attached to the back bottom of the mask.||}}

{{CRLtemplate|File:DZ_gammorean_tunic.jpg|Tunic and Body|
* Body must be suitably shaped and scaled to match screen reference. The belly are should be significantly larger than the upper torso.
* Leather or leather like jerkin covers the upper torso with a central studded circular detail.||}}

{{CRLtemplate|File:DZ_gammorean_undertunic.jpg|Under Tunic|
* A T-shirt like under tunic is worn.
* Under tunic should be made from the same fabric as the scarf.||}}

{{CRLtemplate|File:DZ_gammorean_belt.jpg|Bandolier/Belt|
*Black or dark brown leather / leather-like belt around the waist with large metal round ring located centrally.
*Black or dark brown leather / leather-like belt crossing the body from shoulder to waist||}}

{{CRLtemplate|File:DZ_gammorean_shoulder.jpg|Shoulders|
*Shoulder pauldrons made of metallic looking plates, suitably detailed and with a brown leather/leather-like fixing strap.||}}

{{CRLtemplate|File:Gam_guard_arm.jpg|Arms|
* The face, arms and legs must all be the same shade of green and have the same general finish/texture.
* Arms and hands must be muscular, suitably sized and made with a skin-like texture
* Metallic vambraces/arm braces cover most of the forearm||}}

{{CRLtemplate|File:DZ_gammorean_skirt.jpg|Skirt|
* Lower torso is covered in brown fur like material. May have a tan suede like material or worn fur in the cod area. ||}}

{{CRLtemplate|File:DZ_gammorean_footlegshoe.jpg|Legs, Feet and Sandals|
* The face, arms and legs must all be the same shade of green and have the same general finish/texture.
* Legs and feet must be muscular, suitably sized and made with a skin-like texture
* Black or dark brown sandals made from leather/leather like worn on the feet with leather strapping running up the front with extra strapping wrapping around the shin/calf area.||}}

{{CRLaccessories}}

{{CRLtemplate|File:DZ_gammorean_axe.jpg|Axe|
* Large headed axe with wooden handle as shown.
* Axe must be weathered / show signs of heavy use.||}}

{{CRLtemplate|File:Blankwhite.gif|Spear|||}}

{{CRLtemplate|File:Blankwhite.gif|Rifle|||}}

{{CRLfooter|No_dettachment_CRL|D}}

File:Gam guard arm.jpg

2013-06-09T06:00:55Z

Muppet:

File:Gam guard full.jpg

2013-06-09T06:00:54Z

Muppet: