Revision as of 20:30, 9 November 2011 by Stormtrooperguy (Talk | contribs)
Shadow Stormtrooper
Model TX-5575 , Photo by Lisa Basham


Description: Shadow Stormtrooper
Prefix: TX
Detachment: Spec Ops Detachment

  • This CRL is a work in progress.
  • This costume may be approved by GMLs, but until the library entry is complete, it is suggested that this character first be submitted to the appropriate DL/GML peer review section of the legion forum.
  • If you have this costume and would like to assist with the completion of this library entry, please contact your detachment leader.
  • Please note that the use of the word "should" below does not indicate that the armor piece is considered open to interpretation. All instances of "should be" and "should have" will be replaced with "is" and "has", as this guide is completed.
Required Costume Components

The following costume components are present and appear as described below.

TX shadowstorm helmet.jpeg Helmet
For 501st approval:
  • Lenses must be sufficiently dark enough to obscure the costumer's eyes. They may be flat or bubbled. Acceptable colors are: black, smoke, dark green, or silver.
  • The body of the "ears" may be black or gray. The bars have three or four bumps and may be left the same color as the body or painted black.
  • The frown must have either 6 or 8 teeth cut out and any coloring must not leave the indented area. Acceptable colors are: black, gray or silver. If there are spaces between the teeth the wearer's face must not be seen
  • The tube stripes are black in color and may number between 9 and 15 per side with the curve bends extending backwards. These may be hand painted or decals. There does not need to be the same number per side.
  • Vocoder (vertically ribbed chin detail) may be black or silver.
  • The aerators (cylinders on either side of the vocoder) are black, and screening maybe silver or black.
  • Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) may be: hand painted, decals. Acceptable colors are: black or gray. Rear traps and tears may have vertical black lines.
  • Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
  • Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary.

TK anh stunt neckseal.jpeg Neck Seal
For 501st approval:
  • Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to conceal the entire neck.

TX shadowstorm shoulderstraps.jpeg Shoulder Straps
For 501st approval:
  • These must be securely mounted in front and may free float in back.

TX shadowstorm shoulderbells.jpeg Shoulder Armor
For 501st approval:
  • One on each shoulder. The shoulder bells are considered effectively symmetrical; they may worn interchangeably on the left and right shoulders.

TX shadowstorm biceps.jpeg Upper Arm Armor
For 501st approval:
  • Biceps are fully closed.

TX shadowstorm forearms.jpeg Forearm Armor
For 501st approval:
  • Forearms must appear to be fully sealed and enclosed.

Shadow Trooper Hand Plates.jpg Hand Plates
For 501st approval:
  • Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material but must remain glossy.

TK anh stunt gloves.jpeg Gloves
For 501st approval:
  • Black in color, made of either rubber, nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured.

TX shadowstorm chest.jpeg Chest Armor
For 501st approval:
  • Chest armor overlaps the abdominal armor.

TX shadowstorm back.jpeg Back Armor
For 501st approval:
  • Back plate contains a "O II" design with little or no overlap of the kidney plate.

TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.
  • A navy blue under suit is acceptable when paired with the appropriate helmet as described above.

For level two certification (if applicable):
For level three certification (if applicable):

TX shadowstorm ab.jpeg Abdomen Armor
For 501st approval:
  • The abdomen armor has a button area with 9 gloss black buttons, approximately 7/16" in diameter.

TX shadowstorm kidney.jpeg Kidney Armor
For 501st approval:
  • A single kidney/ posterior armor piece is acceptable.
  • If a separate kidney plate is used, it lines up with the abdomen armor.
  • The top of the kidney armor is flush to or under the back armor.

TX shadowstorm butt.jpeg Posterior Armor
For 501st approval:
  • A single kidney/ posterior armor piece is acceptable.
  • If a separate posterior plate is used, it lines up below the bottom of the belt with with the abdomen armor.
  • There is a minimal gap between the posterior and and kidney armor.

TX shadowstorm belt.jpeg Belt
For 501st approval:
  • Belt face is made of plastic (ammo belt). It is comprised of 6 rectangular boxes, with three square buttons, one centered in the middle and one on each end.
  • Belt proper may be made from glossy black ABS or a similar shiny material and must be 3 to 3.5" wide. Black canvas or similar heavy material may also be used.
  • The drop boxes dangle from the sides of the plastic belt face via black straps and are aligned under the plastic tabs of the ammo belt.

Shadow Trooper Detonator.jpg Thermal Detonator
For 501st approval:
  • (a.k.a. O2 canister) attaches to the back of the belt. This is an all black cylinder 2 to 2.5" in diameter with black end caps and a black control panel pad, with controls closest to the right end cap.

TX shadowstorm thighs.jpeg Thigh Armor
For 501st approval:
  • The thigh armor may open and firmly close in the back allowing the two halves to appear sealed when viewed by spectators. The ammo belt is installed on the bottom of the right thigh.

TX shadowstorm shins.jpeg Lower Leg Armor
For 501st approval:
  • The shin armor is able to open and firmly close in the back allowing the two halves to appear sealed when viewed by spectators. The trapezoid knee plate is affixed to the top of the left shin.

TX shadowstorm boots.jpeg Boots
For 501st approval:
  • Black leather or leather-like, above ankle height, with a flat sole, and small U-shaped elastic sections on both sides of the ankle with no buckles or laces. Jodphur-type boots or an equivalent style. All stitching must be black, and unnecessary or decorative stitching must not be present. Elvis / Mariachi boots are not acceptable.
  • White, or other color boots may be painted black so long as the boots are maintained to remain the proper color.

TX shadowstorm holster.jpeg Holster
For 501st approval:
  • Holster is made of black leather or leather-like material.
  • Holster is worn on the left.
  • Holster may be attached to the belt from behind with rivets, or with loops covering the outside of the belt.

Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.

Generic black pauldron.jpeg Black Pauldron
For 501st approval:
  • Must be black in color and made from vinyl or leather. Must be worn over the right shoulder.

TK anh stunt e11.jpeg E-11 Blaster
For 501st approval:

Manufactured by BlasTech Industries, the E-11 is standard-issue for many Imperial troops. Light, compact yet powerful, the E-11 blaster is always in high demand throughout the galaxy.

  • Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.

For level two certification (if applicable):
  • Folding stock.
    • Stock does not need to function.
  • A real or replica ammo counter - based off of a Hengstler counter - should be present.
  • D-ring mounted on the rear.
  • Correct style scope.
  • Two power cylinders on the magazine.
  • Scratch-built, resin cast, Hyperfirm rubber cast blasters should have a total of 6 t-racks on blaster (leaving the lowest row on the Hengstler side un-covered).
  • If using the Hasbro E11 toy blaster, it is modified to have the correct number of T-tracks (6 total), with a lower row of open vent holes on the magazine housing side.
    • This is accomplished by covering the pre-existing rows of holes with T-tracks, then grinding off the lower integrated T-track on the magazine housing side, and drilling a new row of holes in its place.

Generic-dlt19.jpeg DLT-19 Heavy Blaster Rifle
For 501st approval:

Manufactured by BlasTech Industries, the DLT-19 heavy blaster rifle is much more powerful with a much greater range than the E-11 blaster. Because of its powerful, long range capabilities, this rifle is commonly used on Imperial controlled planets with large, clear, open areas.

  • Based on a real or replica MG-34 machine gun.

For level two certification (if applicable):
  • A DLT-19 is an MG-34 with T-tracks on the barrel, ejection port cover added, and a small disk on left side.

Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.