|
| Shadow Stormtrooper
|
|
Model , Photo by
|
|
|
- This CRL is a work in progress. This costume may be approved by GMLs, but additional research should be done until the CRL is complete.
- If you have this costume and would like to assist with this CRL, please contact your detachment leader!
- Please note that the use of the word "should" below does not indicate that a requirement is optional. All instances of should will be replaced with must as this guide is completed.
|
| Required Costume Components
|
|
The following costume components must be present and appear as described below for approval .
|
|
|
| Helmet
For 501st approval:
- Lenses must be sufficiently dark enough to obscure the costumer's eyes. They may be flat or bubble.
- The black "ear" bars have three of four bumps
- Frown must have either 6 or 8 teeth cut out and any coloring must not leave indented area.
- Tube stripes may number between 9 and 15 per side with the curve bends extending backwards. There does not need to be the same number per side.
- Aerators (cylinders on either side of the vocoder) are black, and screening maybe silver or black.
- Tears, traps, and tube stripes may be: hand painted, decals, or decals that replicate hand painting, they may also be untouched and left as unmodified shiny black helmet material.
- Accepted helmet color combinations are as follows:
- Smoke/black lenses, black frown (gloss), black chin / vocoder (matte or gloss), black tube stripes, tears and temples (matte or gloss).
- Smoke/black lenses, black frown (gloss), black chin / vocoder (matte or gloss), navy blue tube stripes, tears and temples (matte or gloss). This variation is acceptable only when paired with a navy blue undersuit.
- Silver lenses, black frown, black chin, black tube stripes, tears and temples (matte or gloss).
- Silver lenses, silver frown, black or silver/grey chin, black tube stripes, tears and temples (matte or gloss).
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
| Neck Seal
For 501st approval:
- Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to the top of the Adam's apple.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Shoulder Straps
For 501st approval:
- These must be securely mounted in front and may free float in back.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Shoulder Bells
For 501st approval:
- One on each shoulder. The shoulder bells are considered effectively symmetrical; they may worn interchangeably on the left and right shoulders.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Biceps
For 501st approval:
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Forearms
For 501st approval:
- Forearms must be either permanently sealed on both seams or able to open and firmly close provided one seam is permanently closed.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Handplates
For 501st approval:
- Roughly pentagonal in shape, the hand plates are mounted securely over the back of the glove. As an alternative to plastic, these may be made out of latex or latex-like material but must remain shiny.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
| Gloves
For 501st approval:
- Black in color, made of either rubber, nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
- Gloves shall be rubber or rubber-like chemical gloves, in black.
|
|
|
|
| Chest Plate
For 501st approval:
- Chest plate overlaps the abdominal plate.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Back Plate
For 501st approval:
- Back plate contains a "O II" design with little or no overlap of the kidney plate.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
| Under Suit
For 501st approval:
- Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs.
- A navy blue undersuit is acceptable when paired with the appropriate helmet colors as described above.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Abdominal Plate
For 501st approval:
The ab plate has a button area that has 9 gloss black buttons of approximately 7/16" in diameter.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Kidney Plate
For 501st approval:
It is allowable to have a single kidney/butt plate for 501st requirements. If a separate kidney plate is used, it should line up with the ab plate, with the top of the kidney plate being flush to or under the back plate.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Butt Plate
For 501st approval:
- It is allowable to have a single kidney/butt plate for 501st requirements. If a separate butt plate is used, it should line up below the bottom of the belt with with the ab plate, with minimal gap between it and the kidney plate.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Belt
For 501st approval:
- Belt face is made of plastic (ammo belt). It is comprised of 6 rectangular boxes, with three square buttons, one centered in the middle and one on each end.
- Belt proper is made Shiny Black ABS or similar shiny material and must be 3 to 3.5" wide. Black canvas or similar heavy material is also acceptable
- The drop boxes dangle from the sides of the plastic belt face via black straps and are aligned under the plastic tabs of the ammo belt.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Belt
For 501st approval:
- (a.k.a. O2 canister) attaches to the back of the belt. This is an all black cylinder 2 to 2.5" in diameter with black end caps and a black control panel pad, with controls closest to the right end cap.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
NAVIGATION
|
