(Difference between revisions)
|
|
| Line 32: |
Line 32: |
| | {{CRLtemplate|File:TR_ROTJ_Glves.jpg|Gloves| | | {{CRLtemplate|File:TR_ROTJ_Glves.jpg|Gloves| |
| | * Dark Leather Gloves with no extraneous straps/buckles or ornamental stitching. | | * Dark Leather Gloves with no extraneous straps/buckles or ornamental stitching. |
| - | * The gloves should be long enough to cover the wearer's wrists. | + | * The gloves should be long enough to cover the wearer's wrists.| | |}} |
| - | | | |}} | + | |
| | | | |
| | {{CRLtemplate|File:TR_ROTJ_Boots.jpg|Boots| | | {{CRLtemplate|File:TR_ROTJ_Boots.jpg|Boots| |
Revision as of 19:55, 12 April 2011
|
| Imperial Royal Guard, Revenge of the Sith
|
|
| Model TR-2398, Photo by
Andrew Marzka
|
|
|
|
Description: Imperial Royal Guard, Revenge of the Sith
Prefix: TR
Detachment: Sovereign Protectors
Context: Episode III: Revenge of the Sith
Formed at Palpatine's discretion without a formal act, several senators considered them to be illegal. Palpatine justified their creation due to rumors of corruption amongst the Senate Guard. In a galaxy dominated by the blaster, the choice of the force pike as their primary weapon is a declaration of the prowess of the Red Guard.
|
|
|
|
The 501st approval requirements are listed in black.
The Sovereign Protectors Detachment defines two additional, optional levels of costuming excellence: Protector and: Sentential . In the page below, requirements for Protector are listed in blue. Sentinel requirements are in red. Please visit the Sovereign Protectors web site for a full description of these standards.
For 501st membership only the requirements in black need to be met.
|
|
| This CRL is a work in progress and is not yet ready to use for GML approval!
|
|
| Helmet
For 501st approval:
- Finished in a crimson gloss to match the outer robes.
- The visor is fitted with a smoke-tinted visor that allows for maximum visibility while obscuring the wearers features.
|
For level two certification (if applicable):
- The visor has red smoke-tinted visor that allows fr maximum visibility while obscuring the wearers features.
|
For level three certification (if applicable):
|
|
|
| Outer Robes
For 501st approval:
- Constructed of crimson red velvet or velveteen, fully lined in burgundy or dark purple fabric, also preferably velvet or velveteen that matches the inner robe.
- Velour and crushed panne velvet are not acceptable.
- The cloak should cover both the front and back of the wearer, with two arm slits (one on each side) for the wearer's arms; with the front of the robe being sewn to over lap the back.
|
For level two certification (if applicable):
- Shoulder pads to allow for the armored-look without the commitment to armor.
|
For level three certification (if applicable):
|
|
|
| Inner Robes
For 501st approval:
- Burgundy or dark purple cloth thawb, hemmed slightly shorter than the outer cloak.
|
For level two certification (if applicable):
- Neck Seal for “Helmet Off” photos.
|
For level three certification (if applicable):
|
|
|
| Sash
For 501st approval:
- An Obi-style waist sash, approximately 3–4 inches (7.62–10.16cm) made of the same color/material as the wearer's inner robe, Worn over the inner robe.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
| 150px
| Gloves
For 501st approval:
- Dark Leather Gloves with no extraneous straps/buckles or ornamental stitching.
- The gloves should be long enough to cover the wearer's wrists.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
| Boots
For 501st approval:
- Crimson red suede boots, pointed toe, with a relatively conservative heel. There are no visible straps, buckles, or ornamental stitching. The boots cover the wearer's ankles.
|
For level two certification (if applicable):
- (Alternative) Black, texture-less, leather/synthetic leather (non glossy) “Jack” boots", squared toe (rounded toe in ladies styles are acceptable), with a relatively conservative heel, no visible straps/buckles, or ornamental stitching; that reach high enough to cover the wearer's ankles are acceptable as a minimum until red boots can be found.
|
For level three certification (if applicable):
|
|
|
| Forcepike
For 501st approval:
- Four foot (122cm) minimum length, composed of either wood or metal.
- The silver bodied force pike consists of a black pommel, two hand grips at the base, the shaft, and emitter tip.
|
For level two certification (if applicable):
- Black and silver pommel
- BLACK colored grips
- “Activator button” on the grip area
- 'Rasp' emitter end of stacked ring design silver in color.
|
For level three certification (if applicable):
|
|
|
| DH-17 Blaster
For 501st approval:
- Scratch built or high-end prop replica.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
NAVIGATION
|
