501st Legion: Vader's Fist

(Difference between revisions)

Revision as of 21:48, 21 November 2011

Crimson Armor Royal Guard, Crimson Empire

Model TR-xxxx', Photo by '

	Description: Crimson Armor Royal Guard, Crimson Empire Prefix: TR Detachment: Sovereign Protectors Context: Crimson Empire Trilogy Carnor Jax was a Sovereign Protector and aspiring Sith Lord who made a bid for the vacant Imperial throne. An Adversary of Kir Kanos who met his untimely death in a battle on the planet of Yichnorr.

The 501st approval requirements are listed in black.

The Sovereign Protectors Detachment defines two additional, optional levels of costuming excellence: Protector and: Sentential . In the page below, requirements for Protector are listed in blue. Sentinel requirements are in red. Please visit the Sovereign Protectors web site for a full description of these standards.

For 501st membership only the requirements in black need to be met.

This CRL is a work in progress and is not yet ready to use for GML approval!

Required Costume Components
The following costume components must be present and appear as described below for approval .

	Helmet For 501st approval: Finished in a crimson and black gloss finish to match visual references. The visor is fitted with a red visor that allows for maximum visibility while obscuring the wearers features. The visor is cut lower and angled to make a center triangle. Helmet has a crest going from front to back
	For level two certification (if applicable):
	For level three certification (if applicable): {{{5}}}

	Robes/Cape For 501st approval: Constructed of black velvet or velveteen, fully lined in black satin or lightly-reflective material. Robes/Cape must hang no higher than the individual wearer’s calves and no lower than the individual wearer’s ankles. Robes/Cape must have at least one opening to allow for movement and ability to be worn draped over one shoulder. Cloak/Cape closure method cannot be part the bodysuit or armor and must function separately. Velour and crushed panne velvet are not acceptable.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Undersuit For 501st approval: Bodysuit must be constructed of red form fitting material (ex: lycra/spandex) with black accents running vertical along the torso to the thigh. This accent is three inches wide. Neck Seal for “Helmet Off” photos.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Shoulder Bells For 501st approval: One on each shoulder. The shoulder bells are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders and should have a black elastic strap that wraps around the inside of the bicep.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Chest Plate For 501st approval:
	For level two certification (if applicable): {{{4}}}
	For level three certification (if applicable): {{{5}}}

	Abdomen Plate For 501st approval: Done in a gloss black finish. Must be shaped to mimic the visual reference and must contain or show sectional division between plates. A minimum of 3 (three) abdominal plates is required but no more than 8 (eight).
	For level two certification (if applicable): {{{4}}}
	For level three certification (if applicable): {{{5}}}

	Back Plate For 501st approval: Done in a gloss black finish. Must be shaped to mimic the visual reference
	For level two certification (if applicable): {{{4}}}
	For level three certification (if applicable): {{{5}}}

	Gaunlets For 501st approval:
	For level two certification (if applicable): {{{4}}}
	For level three certification (if applicable): {{{5}}}

	Belt For 501st approval:
	For level two certification (if applicable): {{{4}}}
	For level three certification (if applicable): {{{5}}}

	Gloves For 501st approval:
	For level two certification (if applicable): {{{4}}}
	For level three certification (if applicable): {{{5}}}

	Boots For 501st approval: (Black, texture-less, leather/synthetic leather (non glossy) “Knee High boots", squared toe (rounded toe in ladies styles are acceptable), with a relatively conservative heel, no visible straps/buckles, or ornamental stitching.
	For level two certification (if applicable):
	For level three certification (if applicable):

Optional Accessories
Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.

	Glaive For 501st approval:
	For level two certification (if applicable):
	For level three certification (if applicable):

	DH-17 Blaster For 501st approval: Scratch built or high-end prop replica.
	For level two certification (if applicable):
	For level three certification (if applicable):

Retrieved from "http://www.501st.com/databank/Costuming:TR_carnorjax"

Revision as of 21:48, 21 November 2011

NAVIGATION

Operations Docs

Membership

Personal tools

Search

Toolbox