Costuming:TK rotj - Revision history

Muppet at 22:12, 25 March 2013

2013-03-25T22:12:42Z

← Older revision		Revision as of 22:12, 25 March 2013
Line 146:		Line 146:

	{{CRLtemplate\|File:TK_anh_stunt_detonator.jpeg\|Thermal Detonator\|		{{CRLtemplate\|File:TK_anh_stunt_detonator.jpeg\|Thermal Detonator\|
-	*(A.K.A. O2 canister) attaches to the center back of the belt. This is an all gray cylinder without silver stickers or silver paint. The cylinder is between 2” (50mm) and 2.68"(68mm) in diameter with white end caps on each end. The white control panel pad faces upwards, with controls/round washer style detail closest to the right end cap. The total length should be approximately 7.50" (190.5mm). The thermal detonator shall be attached via metal or metallic-appearing clips approximately 3/4" (19mm) wide.\| \|	+	*(A.K.A. O2 canister) attaches to the center back of the belt. This is an all gray cylinder without silver stickers or silver paint. The cylinder is between 2” (50mm) and 2.68"(68mm) in diameter with white end caps on each end. The white control panel pad faces upwards, with controls/round washer style detail closest to the right end cap. The total length should be approximately 7.50" (190.5mm).
		+	*The thermal detonator shall be attached via metal or metallic-appearing clips approximately 3/4" (19mm) wide.\| \|
	*The thermal detonator control panel shall have correct ROTJ details, not ANH/ESB. }}		*The thermal detonator control panel shall have correct ROTJ details, not ANH/ESB. }}

Muppet at 07:20, 23 March 2013

2013-03-23T07:20:28Z

← Older revision		Revision as of 07:20, 23 March 2013
Line 129:		Line 129:
	{{CRLtemplate\|File:TK_rotj_butt.jpg\|Kidney & Butt Plate\|		{{CRLtemplate\|File:TK_rotj_butt.jpg\|Kidney & Butt Plate\|
	*A white flexible U shaped gasket or molded lip shall be present around all edges.		*A white flexible U shaped gasket or molded lip shall be present around all edges.
-	*~~It is allowable to have a~~ separate kidney/butt ~~plate for 501st requirements. If a separate kidney~~ plate is ~~used, it shall line up with the ab plate, with the top of~~ the kidney plate ~~being flush~~ to ~~or under the back plate.If~~ a ~~separate butt plate is used, it should be below the bottom of belt and line up with the kidney plate, with minimal gap between it and the kidney~~ plate.	+	*A separate kidney/butt plate is not allowed - the kidney and butt plate shall be combined/fused to a single plate/one piece.
	*The crotch tab of the butt plate area may or may not have visible snaps.\|		*The crotch tab of the butt plate area may or may not have visible snaps.\|
-	*A separate kidney/butt plate is not allowed - the kidney and butt plate shall be combined/fused to a single plate/one piece.
-
	*The edges of the hip area should be rounded/curved (not like the straight lines found on the ANH/ESB butt plate).\|		*The edges of the hip area should be rounded/curved (not like the straight lines found on the ANH/ESB butt plate).\|
	*There shall be no visible side rivets on the kidney plate, unlike ANH/ESB suits.		*There shall be no visible side rivets on the kidney plate, unlike ANH/ESB suits.

Muppet at 07:13, 23 March 2013

2013-03-23T07:13:20Z

Muppet at 06:43, 23 March 2013

2013-03-23T06:43:43Z

← Older revision		Revision as of 06:43, 23 March 2013
Line 149:		Line 149:

	{{CRLtemplate\|File:TK_anh_stunt_detonator.jpeg\|Thermal Detonator\|		{{CRLtemplate\|File:TK_anh_stunt_detonator.jpeg\|Thermal Detonator\|
-	*(a.k.a. O2 canister) attaches to the back of the belt. This is a gray cylinder between 2" (50mm) and 2.5" (~~64mm~~) in diameter with white end caps ~~and a~~ white control panel pad, with controls closest to the right end cap.\|	+	*(A.K.A. O2 canister) attaches to the center back of the belt. This is an all gray cylinder without silver stickers or silver paint. The cylinder is between 2” (50mm) and 2.68"(68mm) in diameter with white end caps on each end. The white control panel pad faces upwards, with controls/round washer style detail closest to the right end cap. The total length should be approximately 7.50" (190.5mm). The thermal detonator shall be attached via metal or metallic-appearing clips approximately 3/4" (19mm) wide.\| \|
-	*The thermal detonator ~~needs to~~ be attached via metal clips approximately 1"(~~25mm~~) wide~~, and shall be all gray without silver stickers or silver paint~~.\|	+
	*The thermal detonator control panel shall have correct ROTJ details, not ANH/ESB. }}		*The thermal detonator control panel shall have correct ROTJ details, not ANH/ESB. }}

Muppet at 06:39, 23 March 2013

2013-03-23T06:39:32Z

← Older revision		Revision as of 06:39, 23 March 2013
Line 122:		Line 122:

	{{CRLtemplate\|File:TK_rotj_ab.jpg\|Abdomen Plate\|		{{CRLtemplate\|File:TK_rotj_ab.jpg\|Abdomen Plate\|
-	*The ab plate has a button area that matches the color pattern shown (3 dark blue + 6 charcoal grey or black); buttons are approximately 7/16" (11mm) in diameter.	+	*The ab plate has a button area that matches the color pattern shown (3 dark blue + 6 charcoal grey or black); buttons are approximately 7/16" (11mm) in diameter. The three dark blue buttons will be the three buttons closest to the belt.
		+	*Ab plate button detail shall be inverted compared to ANH/ESB.
	*A white flexible U shaped gasket or molded lip shall be present around all edges, bottom, both sides and neck area. \|		*A white flexible U shaped gasket or molded lip shall be present around all edges, bottom, both sides and neck area. \|
-	*The three dark blue buttons will be the three buttons closest to the belt.	+	\|
-		+
-	*Ab plate button detail shall be inverted compared to ANH/ESB.\|	+
	*There shall be no visible split rivet/brad on the cod/crotch and no visible rivets or brads on the left or right side of the ab plate, unlike ANH/ESB.}}		*There shall be no visible split rivet/brad on the cod/crotch and no visible rivets or brads on the left or right side of the ab plate, unlike ANH/ESB.}}

Muppet at 06:36, 23 March 2013

2013-03-23T06:36:36Z

Muppet at 06:34, 23 March 2013

2013-03-23T06:34:25Z

← Older revision		Revision as of 06:34, 23 March 2013
Line 106:		Line 106:

	{{CRLtemplate\|File:TK_rotj_chest.jpeg\|Chest\|		{{CRLtemplate\|File:TK_rotj_chest.jpeg\|Chest\|
-	*Chest plate overlaps the abdominal plate.\|	+	*Chest plate overlaps the abdominal plate.
-	*A white flexible U shaped gasket or molded lip shall be present around all edges, bottom, both sides and neck area.\|	+	*A white flexible U shaped gasket or molded lip shall be present around all edges, bottom, both sides and neck area. \|\|
	*Fabric or elastic strip connecting chest to back shall be either black or not present.		*Fabric or elastic strip connecting chest to back shall be either black or not present.
	*Ideally the AM/FX style chest plate should be replaced with a more screen accurate type. If using an AM/FX style chest plate, it shall be trimmed at the bottom and sides to eliminate the over elongated appearance and to give a more accurate look (Note: Return edge is not required but shall have the rubber gasket).}}		*Ideally the AM/FX style chest plate should be replaced with a more screen accurate type. If using an AM/FX style chest plate, it shall be trimmed at the bottom and sides to eliminate the over elongated appearance and to give a more accurate look (Note: Return edge is not required but shall have the rubber gasket).}}

Muppet at 06:22, 23 March 2013

2013-03-23T06:22:23Z

← Older revision		Revision as of 06:22, 23 March 2013
Line 140:		Line 140:
	*The soft belt proper is tightly woven nylon/cordura like/style material or material with a tightly woven nylon/cordura like/style covering. Size must be 2.25" (57mm) to 2.5" (64mm) wide. The color is to be white to off-white.		*The soft belt proper is tightly woven nylon/cordura like/style material or material with a tightly woven nylon/cordura like/style covering. Size must be 2.25" (57mm) to 2.5" (64mm) wide. The color is to be white to off-white.
	*The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.\|		*The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.\|
-	*Belt shall be tightly woven nylon/cordura style material, or may be canvas, or canvas covered, and the color is to be white to off-white. Leather or vinyl are not acceptable.	+	.\|
-	*Belt shall be between 2.25" (57mm) and 2.5" (64mm) wide, not 3"(90mm) as in ANH/ESB.\|	+
-	*Belt shall be a tightly woven nylon/cordura style material, and the color is to be white to off-white.	+
	*There shall be no square buttons covering the belt rivets (there shall be two rivets, one on each side of the ammo belt).		*There shall be no square buttons covering the belt rivets (there shall be two rivets, one on each side of the ammo belt).
	*Corners of ammo belt shall be cut at right angles, not 45 degrees as in ANH/ESB.		*Corners of ammo belt shall be cut at right angles, not 45 degrees as in ANH/ESB.

Muppet at 02:57, 21 March 2013

2013-03-21T02:57:11Z

← Older revision		Revision as of 02:57, 21 March 2013
Line 138:		Line 138:
	{{CRLtemplate\|File:ROTJ Belt.jpg\|Belt\|		{{CRLtemplate\|File:ROTJ Belt.jpg\|Belt\|
	*Belt face is made of plastic (TK ammo belt).		*Belt face is made of plastic (TK ammo belt).
-	*~~Belt~~ proper is ~~made of canvas, canvas covered~~ material~~, leather,~~ or ~~vinyl, between~~ 2.25" (57mm) to 3" (~~90mm~~) wide. The color is to be white to off-white.	+	*The soft belt proper is tightly woven nylon/cordura like/style material or material with a tightly woven nylon/cordura like/style covering. Size must be 2.25" (57mm) to 2.5" (64mm) wide. The color is to be white to off-white.
	*The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.\|		*The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.\|
	*Belt shall be tightly woven nylon/cordura style material, or may be canvas, or canvas covered, and the color is to be white to off-white. Leather or vinyl are not acceptable.		*Belt shall be tightly woven nylon/cordura style material, or may be canvas, or canvas covered, and the color is to be white to off-white. Leather or vinyl are not acceptable.

Muppet at 23:20, 12 January 2013

2013-01-12T23:20:14Z

← Older revision		Revision as of 23:20, 12 January 2013
Line 171:		Line 171:
	{{CRLtemplate\|File:ROTJ holster.jpg\|Holster\|		{{CRLtemplate\|File:ROTJ holster.jpg\|Holster\|
	*Holster may be omitted from the costume. If a holster is worn, it must be made of completely black leather or leather-like material, and worn on the right side of belt and be attached via the straps behind the belt using two fasteners in the middle of the belt .The fasteners may be rivets, snaps, or Chicago screws. (note: the straps are a little longer for the ROTJ holster, then seen on the other Original Trilogy Stormtroopers).		*Holster may be omitted from the costume. If a holster is worn, it must be made of completely black leather or leather-like material, and worn on the right side of belt and be attached via the straps behind the belt using two fasteners in the middle of the belt .The fasteners may be rivets, snaps, or Chicago screws. (note: the straps are a little longer for the ROTJ holster, then seen on the other Original Trilogy Stormtroopers).
-	*Made of black leather or leather-like material.\|	+	.\|
-	*Holster shall be worn on the right.	+
-	*Holster may be omitted from this costume.\|	+	.\|
-	*Holster shall be attached via straps behind the belt using two rivets in the middle of the strap.}}	+	.}}

	{{CRLaccessories}}		{{CRLaccessories}}

← Older revision		Revision as of 07:13, 23 March 2013
Line 107:		Line 107:
	{{CRLtemplate\|File:TK_rotj_chest.jpeg\|Chest\|		{{CRLtemplate\|File:TK_rotj_chest.jpeg\|Chest\|
	*Chest plate overlaps the abdominal plate.		*Chest plate overlaps the abdominal plate.
-	*A white flexible U shaped gasket or molded lip shall be present around all edges~~, bottom, both sides and neck area~~. \|\|	+	*A white flexible U shaped gasket or molded lip shall be present around all edges.\|\|
	*Fabric or elastic strip connecting chest to back shall be either black or not present.		*Fabric or elastic strip connecting chest to back shall be either black or not present.
	*Ideally the AM/FX style chest plate should be replaced with a more screen accurate type. If using an AM/FX style chest plate, it shall be trimmed at the bottom and sides to eliminate the over elongated appearance and to give a more accurate look (Note: Return edge is not required but shall have the rubber gasket).}}		*Ideally the AM/FX style chest plate should be replaced with a more screen accurate type. If using an AM/FX style chest plate, it shall be trimmed at the bottom and sides to eliminate the over elongated appearance and to give a more accurate look (Note: Return edge is not required but shall have the rubber gasket).}}
Line 113:		Line 113:
	{{CRLtemplate\|File:TK_rotj_back.jpeg\|Back\|		{{CRLtemplate\|File:TK_rotj_back.jpeg\|Back\|
	*Back plate contains a "O II" design.		*Back plate contains a "O II" design.
-	*A white flexible U shaped gasket or molded lip shall be present around all edges~~, bottom, both sides and neck area~~. \|	+	*A white flexible U shaped gasket or molded lip shall be present around all edges. \|\|
-	\|	+
	*Back plate shall have no, or minimal overlap of the kidney plate.		*Back plate shall have no, or minimal overlap of the kidney plate.
	*Ideally the AM/FX style back plate should be replaced with a more screen accurate type. If using an AM/FX style back plate it shall have no, or minimal overlap of the kidney plate and shall be reshaped to emulate a screen used back plate by properly trimming and re-shaping (stretching) the left and right edges of the armor to contour to your body. (Note:Return edge is not required but shall have the rubber gasket). Note: There is currently no tutorial available for this, but you can see an example of this Mod and visual comparison at whitearmor.net}}		*Ideally the AM/FX style back plate should be replaced with a more screen accurate type. If using an AM/FX style back plate it shall have no, or minimal overlap of the kidney plate and shall be reshaped to emulate a screen used back plate by properly trimming and re-shaping (stretching) the left and right edges of the armor to contour to your body. (Note:Return edge is not required but shall have the rubber gasket). Note: There is currently no tutorial available for this, but you can see an example of this Mod and visual comparison at whitearmor.net}}
Line 122:		Line 121:

	{{CRLtemplate\|File:TK_rotj_ab.jpg\|Abdomen Plate\|		{{CRLtemplate\|File:TK_rotj_ab.jpg\|Abdomen Plate\|
		+	*A white flexible U shaped gasket or molded lip shall be present around all edges.
	*The ab plate has a button area that matches the color pattern shown (3 dark blue + 6 charcoal grey or black); buttons are approximately 7/16" (11mm) in diameter. The three dark blue buttons will be the three buttons closest to the belt.		*The ab plate has a button area that matches the color pattern shown (3 dark blue + 6 charcoal grey or black); buttons are approximately 7/16" (11mm) in diameter. The three dark blue buttons will be the three buttons closest to the belt.
-	*Ab plate button detail shall be inverted compared to ANH/ESB.	+	*Ab plate button detail shall be inverted compared to ANH/ESB. \|
-	*A white flexible U shaped gasket or molded lip shall be present around all edges, bottom, both sides and neck area. \|	+
	\|		\|
	*There shall be no visible split rivet/brad on the cod/crotch and no visible rivets or brads on the left or right side of the ab plate, unlike ANH/ESB.}}		*There shall be no visible split rivet/brad on the cod/crotch and no visible rivets or brads on the left or right side of the ab plate, unlike ANH/ESB.}}

	{{CRLtemplate\|File:TK_rotj_butt.jpg\|Kidney & Butt Plate\|		{{CRLtemplate\|File:TK_rotj_butt.jpg\|Kidney & Butt Plate\|
		+	*A white flexible U shaped gasket or molded lip shall be present around all edges.
	*It is allowable to have a separate kidney/butt plate for 501st requirements. If a separate kidney plate is used, it shall line up with the ab plate, with the top of the kidney plate being flush to or under the back plate.If a separate butt plate is used, it should be below the bottom of belt and line up with the kidney plate, with minimal gap between it and the kidney plate.		*It is allowable to have a separate kidney/butt plate for 501st requirements. If a separate kidney plate is used, it shall line up with the ab plate, with the top of the kidney plate being flush to or under the back plate.If a separate butt plate is used, it should be below the bottom of belt and line up with the kidney plate, with minimal gap between it and the kidney plate.
-	*A white flexible U shaped gasket or molded lip shall be present around all edges, bottom, both sides and neck area.
	*The crotch tab of the butt plate area may or may not have visible snaps.\|		*The crotch tab of the butt plate area may or may not have visible snaps.\|
	*A separate kidney/butt plate is not allowed - the kidney and butt plate shall be combined/fused to a single plate/one piece.		*A separate kidney/butt plate is not allowed - the kidney and butt plate shall be combined/fused to a single plate/one piece.

← Older revision		Revision as of 06:36, 23 March 2013
Line 112:		Line 112:

	{{CRLtemplate\|File:TK_rotj_back.jpeg\|Back\|		{{CRLtemplate\|File:TK_rotj_back.jpeg\|Back\|
-	*Back plate contains a "O II" design.\|	+	*Back plate contains a "O II" design.
-	*A white flexible U shaped gasket or molded lip shall be present around all edges, bottom, both sides and neck area.\|	+	*A white flexible U shaped gasket or molded lip shall be present around all edges, bottom, both sides and neck area. \|
		+	\|
	*Back plate shall have no, or minimal overlap of the kidney plate.		*Back plate shall have no, or minimal overlap of the kidney plate.
	*Ideally the AM/FX style back plate should be replaced with a more screen accurate type. If using an AM/FX style back plate it shall have no, or minimal overlap of the kidney plate and shall be reshaped to emulate a screen used back plate by properly trimming and re-shaping (stretching) the left and right edges of the armor to contour to your body. (Note:Return edge is not required but shall have the rubber gasket). Note: There is currently no tutorial available for this, but you can see an example of this Mod and visual comparison at whitearmor.net}}		*Ideally the AM/FX style back plate should be replaced with a more screen accurate type. If using an AM/FX style back plate it shall have no, or minimal overlap of the kidney plate and shall be reshaped to emulate a screen used back plate by properly trimming and re-shaping (stretching) the left and right edges of the armor to contour to your body. (Note:Return edge is not required but shall have the rubber gasket). Note: There is currently no tutorial available for this, but you can see an example of this Mod and visual comparison at whitearmor.net}}
Line 121:		Line 122:

	{{CRLtemplate\|File:TK_rotj_ab.jpg\|Abdomen Plate\|		{{CRLtemplate\|File:TK_rotj_ab.jpg\|Abdomen Plate\|
-	*The ab plate has a button area that matches the color pattern shown (3 dark blue + 6 charcoal grey or black); buttons are approximately 7/16" (11mm) in diameter.\|	+	*The ab plate has a button area that matches the color pattern shown (3 dark blue + 6 charcoal grey or black); buttons are approximately 7/16" (11mm) in diameter.
		+	*A white flexible U shaped gasket or molded lip shall be present around all edges, bottom, both sides and neck area. \|
	*The three dark blue buttons will be the three buttons closest to the belt.		*The three dark blue buttons will be the three buttons closest to the belt.
-	*A white flexible U shaped gasket or molded lip shall be present around all edges.	+
	*Ab plate button detail shall be inverted compared to ANH/ESB.\|		*Ab plate button detail shall be inverted compared to ANH/ESB.\|
	*There shall be no visible split rivet/brad on the cod/crotch and no visible rivets or brads on the left or right side of the ab plate, unlike ANH/ESB.}}		*There shall be no visible split rivet/brad on the cod/crotch and no visible rivets or brads on the left or right side of the ab plate, unlike ANH/ESB.}}
Line 129:		Line 131:
	{{CRLtemplate\|File:TK_rotj_butt.jpg\|Kidney & Butt Plate\|		{{CRLtemplate\|File:TK_rotj_butt.jpg\|Kidney & Butt Plate\|
	*It is allowable to have a separate kidney/butt plate for 501st requirements. If a separate kidney plate is used, it shall line up with the ab plate, with the top of the kidney plate being flush to or under the back plate.If a separate butt plate is used, it should be below the bottom of belt and line up with the kidney plate, with minimal gap between it and the kidney plate.		*It is allowable to have a separate kidney/butt plate for 501st requirements. If a separate kidney plate is used, it shall line up with the ab plate, with the top of the kidney plate being flush to or under the back plate.If a separate butt plate is used, it should be below the bottom of belt and line up with the kidney plate, with minimal gap between it and the kidney plate.
		+	*A white flexible U shaped gasket or molded lip shall be present around all edges, bottom, both sides and neck area.
	*The crotch tab of the butt plate area may or may not have visible snaps.\|		*The crotch tab of the butt plate area may or may not have visible snaps.\|
	*A separate kidney/butt plate is not allowed - the kidney and butt plate shall be combined/fused to a single plate/one piece.		*A separate kidney/butt plate is not allowed - the kidney and butt plate shall be combined/fused to a single plate/one piece.
-	*A white flexible U shaped gasket or molded lip shall be present around all edges.	+
	*The edges of the hip area should be rounded/curved (not like the straight lines found on the ANH/ESB butt plate).\|		*The edges of the hip area should be rounded/curved (not like the straight lines found on the ANH/ESB butt plate).\|
	*There shall be no visible side rivets on the kidney plate, unlike ANH/ESB suits.		*There shall be no visible side rivets on the kidney plate, unlike ANH/ESB suits.