501st Legion: Vader's Fist

(Difference between revisions)

Revision as of 22:20, 23 June 2011

Stormtrooper, Empire Strikes Back

Model TK-7795, Photo by Jason M Kreis TK-4625

	Description: Stormtrooper, Empire Strikes Back Prefix: TK Detachment: First Imperial Stormtrooper Detachment Context: First Imperial Stormtrooper Detachment Episode V: The Empire Strikes Back

The 501st approval requirements are listed in black.

FISD Defines two additional, optional levels of costuming excellence: Expert Infantryman and Centurion. In the page below, requirements for Expert Infantryman are listed in blue. Centurion requirements are in red. Please visit the FISD web site for a full description of these standards.

For 501st membership only the requirements in black need to be met.

Special Notes:

Visit the Frequently asked questions page for information on the Rubies Supreme Stormtrooper costume.
Blasters are not required for legion membership per our weapons policy.
The armor parts shall be made from one of these types of materials or like materials: White fiberglass, ABS (Acrylonitrile Butadiene Styrene), or HIPS (High Impact Polystyrene).

This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.

Required Costume Components
The following costume components must be present and appear as described below for approval .

	Helmet For 501st approval: Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray. Rear traps and tears have vertical black lines. Lenses are a flat smoke or green sufficiently dark enough to obscure the costumer's eyes. The “ear” bars have three or four bumps and should be gray or painted gray, with a black outline. Painting the bumps with rank stripes (highlighted) in black is optional. Frown is painted black and does not leave the teeth area. Eight or six total teeth on the frown are cut out. Tube stripes are medium blue, should be 13 per side, but can be 9 and 16 per side with the curve bends extending backwards. Vocoder (vertically ribbed chin detail) is painted black. Aerators/Hovi mix tips (cylinders on either side of the vocoder) are black or painted black. Tears, traps, and tube stripes should be decals but can be hand painted, or decals that replicate hand painted. Mesh may be used behind the frown to obscure the face of the wearer. Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
	For level two certification (if applicable): Ears shall have three screws used per side, one above and below the ear bar and one at the base of the helmet. Traps/tears and tube stripes shall be decals (with the correct ESB details), no hand-painting or decals that replicate hand painted. Traps/tears may be either ANH gray or a slightly bluer shade of ANH gray. Ear bars shall have four bumps only, not three. Correct 'Hovi mic' aerator tips. FX helmets are not allowed.
	For level three certification (if applicable): MRCE and/or EFX PCR helmets are not allowed. ANHv2 helmets are not allowed. Ear bars shall have only two bumps painted in black (rank stripes). Neck trim shall be of an s-type profile rather than a u-type profile.

	Neck Seal For 501st approval: Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to the top of the Adam's apple.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Shoulder Straps For 501st approval: These shall be securely mounted in front and may free float in back. They may be affixed with rivets, Velcro, or adhesive.
	For level two certification (if applicable): No visible rivets are allowed.
	For level three certification (if applicable): These shall be glued in front. These shall be affixed in the back (no snaps, rivets or brads shall be visible). Straps shall not have a white elastic band securing the shoulder straps to either the chest/back.

	Shoulder Bells For 501st approval: One on each shoulder. The shoulder bells are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Biceps For 501st approval: Biceps are fully closed.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Forearms For 501st approval: Forearms are fully closed.
	For level two certification (if applicable):
	For level three certification (if applicable): No return edge on the inside of the front of the forearm is allowed.

	Hand Plates For 501st approval: These shall be clam shell - or snowtrooper - style hand plates and not the trapezoidal design seen in A New Hope. The hand plates shall be mounted securely over the back of the glove.
	For level two certification (if applicable):
	For level three certification (if applicable): If rubber gloves are worn the hand plates shall be affixed via an elastic strap over the palm. If silk or satin gloves are worn, the hand plates shall have the correct visible stitching pattern using black cotton, with a five point/star pattern, equally spread out with 2 on each side and 1 in the middle front, and needs to be double stitched at each point.

	Gloves For 501st approval: Black in color, made of either rubber, nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured.
	For level two certification (if applicable):
	For level three certification (if applicable): Gloves shall be black rubber or rubber- like chemical gloves or black silk or satin.

	Chest For 501st approval: Chest plate overlaps the abdominal plate.
	For level two certification (if applicable):
	For level three certification (if applicable): Chest and back shall be connected with a white fabric or preferably elastic strap at the shoulders.

	Back For 501st approval: Back plate contains a "O II" design.
	For level two certification (if applicable):
	For level three certification (if applicable): Back plate shall have no, or minimal overlap of the kidney plate.

	Under Suit For 501st approval: Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Abdomen Plate For 501st approval: The ab plate has a button area that matches the color pattern shown (3 blue + 6 gray); buttons are approximately 7/16" in diameter.
	For level two certification (if applicable): Any gap between the ab and kidney plate shall be no more than 1/2" wide. Any shims used to achieve this effect should be of a similar material and color as the ab and kidney plate. Shims shall fit flush and seams are allowed.
	For level three certification (if applicable): Ideally there should be no gap between the ab and kidney plates, just a single visible seam line. Rivets on the left side of the ab plates: a total of three rivets equally spaced out along the depth of the armor and about 10mm from the edge. They may be painted white, or not. A single male snap on the top right corner of the ab plate shall be present. A single split rivet or brad shall be present on the crotch tab of the ab plate. It does not need to be functional.

	Kidney Plate For 501st approval: It is allowable to have a single kidney/butt plate for 501st requirements. If a separate kidney plate is used, it should line up with the ab plate, with the top of the kidney plate being flush to or under the back plate.
	For level two certification (if applicable): A separate kidney plate shall be present, split from the butt plate .
	For level three certification (if applicable): 3 rivets shall be present on the left side of the kidney plate, equally spaced out along the depth of the armor and about 10mm from the edge. They may be painted white, or not.

	Butt Plate For 501st approval: It is allowable to have a single butt/kidney plate for 501st requirements. If a separate butt plate is used, it should be below the bottom of the belt and line up with the kidney plate, with a minimal gap between it and the kidney plate.
	For level two certification (if applicable): A separate butt plate is required, split from the kidney plate.
	For level three certification (if applicable): Two male snaps shall be present on the crotch tab of the butt plate. They do not need to be functional.

	Belt For 501st approval: Belt face is made of plastic (TK ammo belt). Belt proper is made of canvas, canvas covered material, leather, or vinyl, 3” to 3.5” wide. The color is be white to off-white. The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.
	For level two certification (if applicable): Belt shall be canvas or canvas covered, leather and vinyl are not acceptable. There shall be three square buttons, one centered in the middle and one on each end of the plastic ammo belt.
	For level three certification (if applicable): Drop boxes are closed in the back. The corners of the of the plastic ammo belt shall be trimmed at a 45 degree angle.

	Thermal Detonator For 501st approval: (a.k.a. O2 canister) attaches to the back of the belt. This is a gray cylinder between 2” and 2.5" in diameter with white end caps on each end, and a white control panel pad, with controls closest to the right end cap.
	For level two certification (if applicable): The thermal detonator needs to be attached via metal clips approximately 1 inch wide, and shall be all gray without silver stickers or silver paint.
	For level three certification (if applicable):

	Thighs For 501st approval: Thigh armor shall be closed in the back. The small ammo belt is installed on the bottom of the right thigh.
	For level two certification (if applicable):
	For level three certification (if applicable): The thigh ammo belt shall be connected by brads/split rivets only – but not by standard rivets. The bottom corners of the thigh ammo belt shall be rounded off..

	Lower Legs For 501st approval: Greaves close in the back. The trapezoid knee plate (sniper knee plate) is affixed to the left greave and may have two visible brads or rivets securing it to the greave.
	For level two certification (if applicable):
	For level three certification (if applicable): Ideally there should be no visible rivets or brads used to secure the sniper plate to the left greave.

	Boots For 501st approval: White leather or leather-like, above ankle height, with a flat sole with a short heel, and small U-shaped elastic sections on both sides of the ankle with no buckles or laces. Jodhpur/Chelsea-type boots or an equivalent style is acceptable. Elvis or Mariachi boots are not allowed.
	For level two certification (if applicable):
	For level three certification (if applicable): There shall be no seam on the front of the boot (e.g. CABoots are not allowed). Boots shall be lightly scuffed.

	Holster For 501st approval: Made of black leather or leather-like material.
	For level two certification (if applicable): Holster shall be worn on the right and affixed via two loops over the belt. Holster straps shall be completely black.
	For level three certification (if applicable):

Optional Accessories
Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.

	BlasTech E-11 (canon) For 501st approval: Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.
	For level two certification (if applicable): Folding stock (does not need to function). No ammo counter shall be present. D-ring mounted on the rear. Correct style scope. No power cylinders on the magazine housing. Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 6 T-tracks on blaster (leaving the lowest row on the magazine housing side uncovered). Popular commercially available toy Stormtrooper blasters have a total of 7 T-tracks (if you cover all the rows of holes) or 6 T-tracks (if you cover the "open row" of holes on the magazine housing side. Below this, you shall grind off the lower T-track and drill a new row of holes).
	For level three certification (if applicable): Hasbro blasters are not allowed, even conversions.

	BlasTech E-11 (promo) For 501st approval: Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.
	For level two certification (if applicable): Folding stock (does not need to function). No ammo counter shall be present. Correct style scope. No power cylinders on the magazine housing. Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 6 T-tracks on blaster (leaving the lowest row on the magazine housing side uncovered). Popular commercially available toy Stormtrooper blasters have a total of 7 T-tracks (if you cover all the rows of holes) or 6 T-tracks (if you cover the "open row" of holes on the magazine housing side. Below this, you shall grind off the lower T-track and drill a new row of holes). Two greeblies on the left rear area. Three studs on the right rear area. Add two scope block greeblies. Remove front bayonet muzzle disk. Remove magazine housing parts. Remove D-Ring mount. Swoosh trim on right side above the pistol grip.
	For level three certification (if applicable): Hasbro blasters are not allowed, even conversions.

Retrieved from "http://www.501st.com/databank/Costuming:TK_esb"

Revision as of 22:20, 23 June 2011

NAVIGATION

Operations Docs

Membership

Personal tools

Search

Toolbox