(Difference between revisions)
Line 159: Line 159:
*No ammo counter shall be present.
*No ammo counter shall be present.
*D-ring mounted on the rear.
*D-ring mounted on the rear.
-
*Correct style scope.
+
*Sterling based blasters have the correct M-38 or M-19 style scope.
 +
**The M-19 scope is preferred.
*No power cylinders on the magazine housing.
*No power cylinders on the magazine housing.
*Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 6 T-tracks on blaster (leaving the lowest row on the magazine housing side uncovered).
*Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 6 T-tracks on blaster (leaving the lowest row on the magazine housing side uncovered).
Line 181: Line 182:
*Swoosh trim on right side above the pistol grip.|
*Swoosh trim on right side above the pistol grip.|
*Hasbro blasters are not allowed, even conversions.}}
*Hasbro blasters are not allowed, even conversions.}}
-
 
{{CRLfooter|FISD_CRL|T}}
{{CRLfooter|FISD_CRL|T}}

Revision as of 02:25, 9 May 2014

crlblackhd.gif
Stormtrooper, Empire Strikes Back
ESBtk.jpg
Model TK-7795, Photo by Jason M Kreis TK-4625


FISD.png

Description: Stormtrooper, Empire Strikes Back
Prefix: TK
Detachment: First Imperial Stormtrooper Detachment
Context: Episode V: The Empire Strikes Back

The Stormtroopers are the main force during the capture and interrogation of the Rebels, Han Solo, Princess Leia Organa, Chewbacca and their droid C3PO on the Cloud City of Bespin. These highly trained elite soldiers cannot be bribed or swayed from their dedication to the Empire. The Stormtroopers are not only the first strike team units sent into critical combat situations, but are also assigned to keep a watchful eye over the Imperial officers who might betray the Emperor’s cause. Garrisons of Stormtroopers are stationed on worlds throughout the Galaxy to keep order, and stop any Rebel uprisings. Even though the Stormtroopers are an independent unit, having their own command structure, ranking system and support facilities, they still serve on Imperial vessels, and operate along side the Imperial army and navy. The Stormtroopers are shielded by hardened, plastoid,composite armor, fitted over a black environmental body glove, with a built-in life support system. The imposing white armor not only protects them from harsh environments, but also gives limited protection from blaster fire. Stormtroopers carry an array of equipment and weapons ,wielding blaster rifles and pistols with great skill. The Stormtroopers, having the combined training and battle tactics of both an Army soldier and a Marine, makes them highly adaptable and a very skilled force.


The 501st approval requirements are listed in black.

FISD Defines two additional, optional levels of costuming excellence. In the page below, requirements for Level 2 "Expert Infantryman" are listed in blue. Requirements for Level 3 "Centurion" are listed in red.

  • Those armor pieces without blue and/ or red text are by default considered the highest level.
  • Please visit the FISD web site for a full description of these standards.

For 501st membership only the requirements in black need to be met.

Special Notes:

  • Visit the Frequently asked questions page for information on the Rubies Supreme Stormtrooper costume.
  • Blasters are not required for legion membership per our weapons policy.
  • The armor parts shall be made from one of these types of materials or like materials: White fiberglass, ABS (Acrylonitrile Butadiene Styrene), HIPS (High Impact Polystyrene), or Polyvinyl chloride (PVC).
  • FX armor may not be used for Level 3 approval.

This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
  • Any uncertainties or questionable aspects of the submitted costume should be brought to the appropriate DL/GML peer review section of the legion forum.
Required Costume Components

The following costume components are present and appear as described below.

TK esb helmet.jpeg Helmet
For 501st approval:
  • Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray.
  • Rear traps and tears have vertical black lines.
  • Lenses are a flat smoke or green sufficiently dark enough to obscure the costumer's eyes.
  • The “ear” bars have three or four bumps and should be gray or painted gray, with a black outline. Painting the bumps with rank stripes (highlighted) in black is optional.
  • Frown is painted black and does not leave the teeth area. Eight or six total teeth on the frown are cut out.
  • Tube stripes are medium blue, should be 13 per side, but can be 9 and 16 per side with the curve bends extending backwards.
  • Vocoder (vertically ribbed chin detail) is painted black.
  • Aerators/Hovi mix tips (cylinders on either side of the vocoder) are black or painted black.
  • Tears, traps, and tube stripes should be decals but can be hand painted, or decals that replicate hand painted.
  • Mesh may be used behind the frown to obscure the face of the wearer.
  • Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
  • Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary. Please visit FISD/whitearmor.net for more info on these modifications.
For level two certification (if applicable):
  • Ears shall have three screws used per side, one above and below the ear bar and one at the base of the helmet.
  • Traps/tears and tube stripes shall be decals (with the correct ESB details), no hand-painting or decals that replicate hand painted.
  • Traps/tears may be either ANH gray or a slightly bluer shade of ANH gray.
  • Ear bars shall have four bumps only, not three.
  • Correct 'Hovi mic' aerator tips.
  • FX helmets are not allowed.
For level three certification (if applicable):
  • MRCE and/or EFX PCR helmets are not allowed.
  • ANHv2 helmets are not allowed.
  • Ear bars shall have only two to three bumps painted in black (rank stripes).
  • Neck trim shall be of an s-type profile rather than a u-type profile.
TK anh stunt neckseal.jpeg Neck Seal
For 501st approval:
  • Black with horizontal ribs, fitted to the wearer, and extending from the base of the neck to the top of the Adam's apple.
For level two certification (if applicable):
For level three certification (if applicable):
TK anh stunt shoulders.jpeg Shoulder Straps
For 501st approval:
  • These shall be securely mounted in front and may free float in back. They may be affixed with rivets, Velcro, or adhesive.
For level two certification (if applicable):
  • No visible rivets are allowed.
For level three certification (if applicable):
  • These shall be glued in front.
  • These shall be affixed in the back (no snaps, rivets or brads shall be visible).
  • Straps shall not have a white elastic band securing the shoulder straps to either the chest/back.
TK anh stunt shoulder.jpeg Shoulder Bells
For 501st approval:
  • One on each shoulder. The shoulder bells are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders.
For level two certification (if applicable):
  • Ideally no shoulder bell straps across the biceps.If there is a shoulder bell strap, it shall not be visible across the biceps.
For level three certification (if applicable):
TK anh stunt biceps.jpeg Biceps
For 501st approval:
  • Biceps are fully closed.
For level two certification (if applicable):
For level three certification (if applicable):
  • Biceps must be constructed using the butt joint and cover strip method. Overlap construction is not allowed.
TK anh stunt forearms.jpeg Forearms
For 501st approval:
  • Forearms are fully closed.
For level two certification (if applicable):
For level three certification (if applicable):
  • No return edge on the inside of the front of the forearm is allowed.
  • Forearms must be constructed using the butt joint and cover strip method. Overlap construction is not allowed.

TK esb handplates.jpeg Hand Plates
For 501st approval:
  • These shall be clam shell, or snowtrooper-style hand plates and not the trapezoidal design seen in A New Hope. The hand plates shall be mounted securely over the back of the glove.
For level two certification (if applicable):
For level three certification (if applicable):
  • If rubber gloves are worn the hand plates shall be affixed via an elastic strap over the palm.
  • If silk or satin gloves are worn, the hand plates shall have the correct visible stitching pattern using black cotton, with a five point/star pattern, equally spread out with 2 on each side and 1 in the middle front, and needs to be double stitched at each point.

TK anh stunt gloves.jpeg Gloves
For 501st approval:
  • Black in color, made of either rubber, nomex, leather, or leather-like material, with no visible straps or logos/designs. The fingers are enclosed, non-textured.
For level two certification (if applicable):
For level three certification (if applicable):
  • Gloves shall be black rubber or rubber- like chemical gloves or black silk or satin.

TK anh stunt chest.jpeg Chest
For 501st approval:
  • Chest plate overlaps the abdominal plate.
For level two certification (if applicable):
For level three certification (if applicable):
  • Chest and back shall be connected with a white fabric or preferably elastic strap at the shoulders.
  • AM chest plate must be replaced with a more screen accurate version.

TK anh stunt back.jpeg Back
For 501st approval:
  • Back plate contains a "O II" design.
For level two certification (if applicable):
For level three certification (if applicable):
  • Back plate shall have no, or minimal overlap of the kidney plate.
  • AM back plate must be replaced with a more screen accurate version.

TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos/designs.
For level two certification (if applicable):
For level three certification (if applicable):
TK anh stunt ab.jpeg Abdomen Plate
For 501st approval:
  • The ab plate has a button area that matches the color pattern shown (3 blue + 6 gray); buttons are approximately 7/16"(11mm) in diameter.
For level two certification (if applicable):
  • Any gap between the ab and kidney plate shall be no more than 1/2"(12.5mm) wide. Any shims used to achieve this effect should be of a similar material and color as the ab and kidney plate. Shims shall fit flush and seams are allowed.
For level three certification (if applicable):
  • Ideally there should be no gap between the ab and kidney plates, just a single visible seam line.
  • Rivets on the left side of the ab plate: a total of three fasteners, the heads should be rounded or domed, solid, approximately 5/16" (8mm) diameter and equally spaced out along the depth of the armor and about 10mm from the edge. They may be painted white, or not. Paperclip brads are not considered to have a domed head. Note: For the original TK armor the type of rivets used were bifurcated rivets or split rivets.
  • A single male snap on the top right corner of the ab plate shall be present.
  • A single split rivet or brad shall be present on the crotch tab of the ab plate. It does not need to be functional.
  • Ab plate buttons must be integrated and painted directly on the plate, no separate buttons are allowed.
TK anh stunt kidney.jpeg Kidney Plate
For 501st approval:
  • A separate kidney plate shall be present, split from the butt plate.
For level two certification (if applicable):
For level three certification (if applicable):
  • Three rivets shall be present on the left side of the kidney plate, the heads should be rounded or domed, solid, approximately 5/16"(8mm) diameter and equally spaced out along the depth of the armor and about 10mm from the edge. They may be painted white, or not. Paperclip brads are not considered to have a domed head. Note: For the original TK armor the type of rivets used were bifurcated rivets or split rivets.
TK anh stunt butt.jpeg Posterior armor
For 501st approval:
  • A separate butt plate is required, split from the kidney plate.
For level two certification (if applicable):
For level three certification (if applicable):
  • Two male snaps shall be present on the crotch tab of the butt plate. They do not need to be functional.
TK anh stunt belt.jpeg Belt
For 501st approval:
  • Belt face is made of plastic (TK ammo belt).
  • The soft belt proper is made of canvas, or material with a canvas covering. Size must be 2.75” (70 mm) to 3.25”(83 mm) wide and not wider than the plastic portion of the belt. The color is be white to off-white.
  • The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.
For level two certification (if applicable):
  • There shall be three square buttons, one centered in the middle and one on each end of the plastic ammo belt.
For level three certification (if applicable):
  • Drop boxes must have full inner drop boxes to close the back. Flat covers are not allowed.
  • Drop boxes are vertically aligned with the end of the ammo belt with minimal gap between belt and box.
  • The corners of the of the plastic ammo belt shall be trimmed at a 45 degree angle.
TK anh stunt detonator.jpeg Thermal Detonator
For 501st approval:
  • (A.K.A. O2 canister) attaches to the center back of the belt. This is an all gray cylinder without silver stickers or silver paint. The cylinder is between 2” (50mm) and 2.68"(68mm) in diameter with white end caps on each end. The white control panel pad faces upwards, with controls/round washer style detail closest to the right end cap. The total length should be approximately 7.50" (190.5mm).
  • The thermal detonator shall be attached via metal or metallic-appearing clips approximately 1" (25mm) wide.
For level two certification (if applicable):
  • Thermal detonator belt clips should be positioned with little to no gap between the clips and the end caps.
For level three certification (if applicable):
TK anh stunt thighs.jpeg Thighs
For 501st approval:
  • Thigh armor shall be closed in the back.
  • The small ammo belt is installed on the bottom of the right thigh.
For level two certification (if applicable):
For level three certification (if applicable):
  • Thigh ammo belt must be attached to thigh with a solid head rivet or fastener in the upper corner and fastened to the lower thigh ridge. Standard pop rivets are not allowed.
  • The bottom corners of the thigh ammo belt shall be rounded off.
  • Thighs must be constructed using the butt joint and cover strip method. Overlap construction is not allowed.
TK anh stunt shins.jpeg Lower Legs
For 501st approval:
  • Greaves close in the back. The trapezoid knee plate (sniper knee plate) is affixed to the left greave and may have two visible brads or rivets securing it to the greave.
  • The AM greaves (shins) shall be on the proper legs, with a new cover strip. The cover strip edge shall be facing the inside of the leg. Note: There is a manufacturer defect with the AM greaves (shins) that may cause you to wear the them improperly. Please see the Tutorial titled :"AM armor shins: the proper way to assemble and wear", on the whitearmor.net
For level two certification (if applicable):
  • Sniper knee plate must be aligned with the ridges on the shin.
  • Sniper knee plate must not have visible rivets or fasteners attaching it to the shin.
For level three certification (if applicable):
  • Lower legs must be constructed using the butt joint and cover strip method. Overlap construction is not allowed.
TK anh stunt boots.jpeg Boots
For 501st approval:
  • Boots are above ankle height and made of white leather or leather-like material.
  • Small U-shaped elastic sections on both sides of the ankle.
  • Flat sole with a short heel.
  • No buckles or laces.
  • Jodhpur/ Chelsea-type boots or an equivalent style is acceptable.
    • Elvis or Mariachi boots are not allowed.
For level two certification (if applicable):
For level three certification (if applicable):
  • Boots shall be lightly scuffed.
  • There shall be no seam on the front of the boot.
TK esb holster.jpeg Holster
For 501st approval:
  • Holster is worn on right side of belt. Holster will be made of completely black leather or leather-like material and be worn on the right and affixed via two black loops over the belt (no fasteners).
For level two certification (if applicable):

.

For level three certification (if applicable):
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.

TK esb blaster1.jpeg BlasTech E-11 (canon)
For 501st approval:
  • Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.
For level two certification (if applicable):
  • Folding stock (does not need to function).
  • No ammo counter shall be present.
  • D-ring mounted on the rear.
  • Sterling based blasters have the correct M-38 or M-19 style scope.
    • The M-19 scope is preferred.
  • No power cylinders on the magazine housing.
  • Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 6 T-tracks on blaster (leaving the lowest row on the magazine housing side uncovered).
  • If using the Hasbro E11 toy blaster and you cover all the rows of holes, the blaster will have 7 T-tracks total. But, if you want to have the correct number of T-tracks (6 total) with the lower row of open vent holes on the magazine housing side, then you shall cover the pre-existing rows of holes with T-tracks, and grind off the lower integrated T-track on the magazine housing side and drill a new row of holes in its place.
For level three certification (if applicable):
  • Hasbro blasters are not allowed, even conversions.
TK esb blaster2.jpeg BlasTech E-11 (promo)
For 501st approval:
  • Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.
For level two certification (if applicable):
  • Folding stock (does not need to function).
  • No ammo counter shall be present.
  • Correct style scope.
  • No power cylinders on the magazine housing.
  • Scratch-built, resin cast, Hyperfirm rubber cast blasters shall have a total of 6 T-tracks on blaster (leaving the lowest row on the magazine housing side uncovered).
  • If using the Hasbro E11 toy blaster and you cover all the rows of holes, the blaster will have 7 T-tracks total. But, if you want to have the correct number of T-tracks (6 total) with the lower row of open vent holes on the magazine housing side, then you shall cover the pre-existing rows of holes with T-tracks, and grind off the lower integrated T-track on the magazine housing side and drill a new row of holes in its place.
  • Two greeblies on the left rear area.
  • Three studs on the right rear area.
  • Add two scope block greeblies.
  • Remove front bayonet muzzle disk.
  • Remove magazine housing parts.
  • Remove D-Ring mount.
  • Swoosh trim on right side above the pistol grip.
For level three certification (if applicable):
  • Hasbro blasters are not allowed, even conversions.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:TK_esb

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.