Revision as of 10:20, 11 November 2011 by Stevechewbacca (Talk | contribs)
TIE Pilot, A New Hope
TI pilot anh.jpg
Model TI 6854, Photo by Ed Eliason


Description: TIE Pilot, ANH
Prefix: TI
Detachment: Jolly Roger Squadron
Context: Star Wars Episode 4
TIE pilots served in the Imperial Navy by piloting the various TIE series starfighters.

Template:CRLwipgmlapproval fr

Composants de Costume Requis

Les composants de costumes suivants doivent être présents et apparaître comme décrit ci-dessous pour l’approbation.

TI rotj helmet.jpg Casque
For 501st approval:
  • See the TIE Helmet Detail page for more views and information about canon paint schemes.
  • Helmet may have flat or bubbled lenses in Dark Gray or Dark Green.
  • The helmet must also have imperial disks (greeblies) on the ear wells.
  • Two 2.75" diameter Imperial Emblems in either white or silver should be on the crest of the helmet as seen in the diagrams below.

For level two certification (if applicable):
  • The frown between the teeth may be drilled out but if so, then it must be backed by material so that the face is not seen.
  • Colours of markings may range from chrome to silver, brushed aluminum to light gray to dark gray (gun metal), but must be consistent - pick a colour and stick with it
For level three certification (if applicable):

Blankwhite.gif Hoses
For 501st approval:
  • Black Ribbed Hoses with a 1.25" diameter and 18" to 21" in length from the helmet hose port to connect to the chestbox upper hose ports.

For level two certification (if applicable):
For level three certification (if applicable):

Generic Balaclava.jpg Balaclava
For 501st approval:
  • A balaclava is a black head sock/hood that is worn under the helmet and is used primarily to hide any view of the wearer's skin and/or facial hair.

Generic-black-coverall.jpg Black Imperial Flight Suit
For 501st approval:
  • One piece black coverall/jumpsuit/flight suit with a front invisible zipper.
  • Approximately 1.5" (38.1mm) tall mandarin collar with a chevron shaped, left-over-right velcro closure.
  • A silver or white Imperial Cog emblem, on a black background, is present on both shoulders.
    • The cog is 3" or 3.5" in diameter, and 1" from the shoulder seam.
  • On the left forearm there is a compad pocket, approximately 5" (127mm) wide by 5.75" (146.05mm) tall, with no flap and a 2.25" (57.15mm) window in it.
    • Size might vary to match specific compad.
  • On the left bicep, about 2"(50.8mm) below the cog emblem, there is a code cylinder pocket with no flap, and vertical stitching dividing it into pen sleeves.
  • The bottom front corner of the pocket is cut off at a bevel on the side pointing in view direction, with the broader upside forming the border of the pen sleeves.
  • The right sleeve has a cargo pocket, about 6" (152mm) wide and 5.75" (146mm) on the bicep, and approximately 2"(50.8mm) below the cog emblem.
    • The pocket has a 2"(50.8mm) flap.
  • (2) large chest pockets and (2) large front pockets below the belt, without any zipper or flaps.
  • (2) leg pockets with flaps, similar in proportion as the right arm sleeve pocket.
    • Size may differ - (Usually the width of the front pockets equals the width of the leg pockets).
  • There are no rank bars of any kind on the uniform.
  • There are no leg pockets below the knees.

For level two certification (if applicable):
  • Imperial patches on the shoulders are printed vinyl rather than embroidered.
  • The suit has a pointed collar in the back.

Generic-commpad.jpg Imperial Communications Pad
For 501st approval:
  • Rectangular communications pad, with buttons and detailing as shown, on a grey or silver background.

For level two certification (if applicable):
  • Compad is not electronically lit.

TI armor.jpg Armure
For 501st approval:
  • Should consist of the front and back armor as shown, with two shoulder straps anchored by an octagon of plastic on each end. Black Nylon webbing or elastic should also be allowed to aid in the snug fit of the armor. The shoulder straps should not be load bearing. Being plastic they can crack.

For level two certification (if applicable):
For level three certification (if applicable):

TI ANH chest box.jpg Chestbox
For 501st approval:
  • The chestbox is required to have the same configurations as seen in these photos.
  • The box has 4 1" square x 1/8th" thick detail pieces. There are several canon configurations that are acceptable:
    • 2 white, 2 blue
    • 1 Red, 1 White, 2 Blue
    • 1 Gray, 1 White, 2 Blue.
  • The rockers are always 2 Gray with dots or lamps in their bottom (LEDs or Lights are optional but should be approved.)

For level two certification (if applicable):
For level three certification (if applicable):

ID belt.jpg Ceinture
Pour l'approbation 501e:
  • La ceinture est construite à partir d'un cuir non texturé ou un matériau analogue à du cuir.
  • La ceinture est d'environ 2 "(5,1 cm) de largeur, mais une largeur allant jusqu'à 3" (7,6 cm) est acceptable.
  • Il n'y a pas de boucles sur la bande.
  • Un grand encliquetage ou un rivet seule est visible environ 1 "(2,5 cm) de la boucle.
    • La ceinture peut être porté avec le composant logiciel enfichable vers la droite ou la gauche de l'utilisateur.
  • La boucle est construit à partir d'un métal brossé horizontalement, ou en métal matériau regardant.
  • La taille de la boucle est d'environ 2 5/8 "(6,7 cm) de hauteur et 4 1/8" (10,5 cm) de large par 0,5 "(1,25 cm) de rayon des coins arrondis.
  • La boucle est ornée d'un Imperial Code Disk au centre.
  • S’il vous plaît se référer à la page de référence Imperial Buckle pour l’information sur les styles précis et inexactes.
Pour la deuxième niveau de certification (le cas échéant):
  • La ceinture est réalisée en cuir.
  • L'encliquetage est porté à la gauche de l'utilisateur.
  • La boucle a une courbe horizontale légère.

Black-gauntlet-gloves.jpeg Black Gauntlet Gloves
For 501st approval:
  • Black, leather or leather-like, enclosed fingered, non-textured, fitted gauntlet style.
  • No buckles, straps, or decorative stitching.
  • Three straight lines, on the back of the hand (that match some references), are optional.

For level two certification (if applicable):
  • Gloves are made of leather.
For level three certification (if applicable):
  • Gauntlets slightly flair-out, upward from the wrist to the mid-forearm.

Generic-black-boots.jpeg Black Boots
For 501st approval:
  • Calf high black leather or leather like material.
  • Free of laces, decorative stitching, buckles on the instep or any other embellishments.
  • Boots may have a single adjustment strap at the top outside of the boot, with the buckle no wider than 1".
    • This need not be functional.
  • Zippers on the inside of the boot are acceptable, so long as they are concealed.
    • If the zipper is not covered by vinyl/leather, it is painted black.
  • German "jack boot" style boots are most canon.

For level two certification (if applicable):
  • Boots are made of leather.
For level three certification (if applicable):
  • Boots are German jack boots (or “Knobelbechers”) or an authentic replication thereof.
  • Boots have the top adjustment strap.

Accessoires Optionnels

Les items ci-dessous sont des accessoires optionnels du costume. Ces items ne sont pas requis pour l’approbation, mais si présents ils doivent respecter les directives ci-dessous.

Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.