(Difference between revisions)
(10 intermediate revisions not shown)
Line 1: Line 1:
-
{{CRLheader|Clone Trooper Sergeant|COSTUME IMAGE|MODEL NAME|PHOTOGRAPHER NAME}}
+
{{CRLheader|Clone Trooper Sergeant|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}
{{CRLdetinfo| 1111 |Clone Trooper Sergeant|TC|Episode II: Attack of the Clones|
{{CRLdetinfo| 1111 |Clone Trooper Sergeant|TC|Episode II: Attack of the Clones|
-
Clone troopers were an army of identical, genetically-modified clones of Jango Fett, created to serve in the Grand Army of the Republic during the conflict that came to be known as the Clone Wars. Cloned and raised in the cities of Kamino, the clone  troopers trained and drilled since birth, and came to be regarded as one of the most efficient military forces ever to have existed in galactic  history. This was not only due to their training, but also to their unwavering loyalty to the Galactic Republic and its leader, Supreme Chancellor Palpatine. }}
+
Clone troopers were an army of identical, genetically-modified clones of Jango Fett, created to serve in the Grand Army of the Republic during the conflict that came to be known as the Clone Wars. Cloned and raised in the cities of Kamino, the clone  troopers trained and drilled since birth, and came to be regarded as one of the most efficient military forces ever to have existed in galactic  history. This was not only due to their training, but also to their unwavering loyalty to the Galactic Republic and its leader, Supreme Chancellor Palpatine.
-
{{CRLwipapproval}}
+
{{RL_approved}} }}
-
{{CRLsubheading|Costume Components}}
+
{{CRLctnlevels}}
-
{{CRLtemplate|actual picture| Helmet|
+
{{CRLwipgmlapproval}}
 +
 
 +
{{CRLrequirements}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Sergeant Command Colors|
 +
* In the CRL below you will see references to command colors/markings/paint.
 +
* For the sergeant, the command color is green.
 +
* Testors Go Green is an example of a suitable shade.||}}
 +
 
 +
 
 +
{{CRLtemplate|File:AOTC E2 Clone sergeantr helmet copy.jpg| Helmet|
*Episode 2 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Episode 2 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
*Visor - Mirrored Chrome or Black Visor.
*Visor - Mirrored Chrome or Black Visor.
Line 25: Line 35:
*Rear fin light to be lit. Light is steady, does not blink, and is composed of 3 LEDs. }}
*Rear fin light to be lit. Light is steady, does not blink, and is composed of 3 LEDs. }}
-
{{CRLtemplate|PART IMAGE|Neck Seal|
+
{{CRLtemplate|File:Clone trooper neck seal.jpg|Neck Seal|
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.| |}}
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.| |}}
Line 31: Line 41:
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.| | }}
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.| | }}
-
{{CRLtemplate|PART IMAGE|Shoulder Bells|
+
{{CRLtemplate|File:AOTC clone sergeant shoulder bells copy.jpg|Shoulder Bells|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
** Command paint follows the contour the the shoulder armor. Front should line should match upper arm location and rear shoulder line should match with rear upper arm line. The command stripe should be continuous from one part to the next.
** Command paint follows the contour the the shoulder armor. Front should line should match upper arm location and rear shoulder line should match with rear upper arm line. The command stripe should be continuous from one part to the next.
Line 37: Line 47:
*Shoulder bells should not be symmetrical.  The Shoulder bells should slightly curve back at the bottom of the shoulder. }}
*Shoulder bells should not be symmetrical.  The Shoulder bells should slightly curve back at the bottom of the shoulder. }}
-
{{CRLtemplate|PART IMAGE|Upper Arm Armor|
+
{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
**Command paint semi covers some tricept indentation and 1/2" around the front of the bicep.  
**Command paint semi covers some tricept indentation and 1/2" around the front of the bicep.  
Line 43: Line 53:
*Armor should be seamless.  No visible traces of how the armor was assembled should be shown. | |}}
*Armor should be seamless.  No visible traces of how the armor was assembled should be shown. | |}}
-
{{CRLtemplate|PART IMAGE|Elbow Armor|  
+
{{CRLtemplate|File:Blankwhite.gif|Elbow Armor|  
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
** Command paint covers the outside of the elbow and 1/2" - 3/4" of the return. The remainder is white.
** Command paint covers the outside of the elbow and 1/2" - 3/4" of the return. The remainder is white.
Line 50: Line 60:
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}
-
{{CRLtemplate|PART IMAGE|Forearm Armor|
+
{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
** Command paint starts at the back of the bottom triangle of the forearm and continues in a straigh line to the top of the forearm. The top line starts 1/4" from compad location on right arm and continues in a vertical line. The area between these two lines should be filled in with command coloring. Match this to the left arm.
** Command paint starts at the back of the bottom triangle of the forearm and continues in a straigh line to the top of the forearm. The top line starts 1/4" from compad location on right arm and continues in a vertical line. The area between these two lines should be filled in with command coloring. Match this to the left arm.
Line 61: Line 71:
*Instead of a hard edge the top of the forearm has a bone ridge.}}
*Instead of a hard edge the top of the forearm has a bone ridge.}}
-
{{CRLtemplate|PART IMAGE|Hand Plates|
+
{{CRLtemplate|File:AOTC clone sergeant hand plates.jpg|Hand Plates|
*Hand plates are mirror images of each other.   
*Hand plates are mirror images of each other.   
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.
** Handplates should be completely colored with command coloring. | | }}
** Handplates should be completely colored with command coloring. | | }}
-
{{CRLtemplate|PART IMAGE|Gloves|
+
{{CRLtemplate|File:Blankwhite.gif|Gloves|
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}
-
{{CRLtemplate|PART IMAGE|Chest Armor|
+
{{CRLtemplate|File:AOTC clone sergeant chest copy.jpg|Chest Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
** There should be 4 3/4" dots horitantal to the ground centered on the left breast in command coloring
** There should be 4 3/4" dots horitantal to the ground centered on the left breast in command coloring
Line 78: Line 88:
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}
-
{{CRLtemplate|PART IMAGE|Back Armor|
+
{{CRLtemplate|File:Clone back.jpg|Back Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
Line 87: Line 97:
*Highly detailed resin insert should replace softer details. }}
*Highly detailed resin insert should replace softer details. }}
-
{{CRLtemplate|PART IMAGE|Ab Armor|
+
{{CRLtemplate|File:Clone abb2.jpg|Ab Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
Line 95: Line 105:
* Ab section should be seamless at the sides and close in the back.  A detail plate should cover the seam line and hide all work.}}
* Ab section should be seamless at the sides and close in the back.  A detail plate should cover the seam line and hide all work.}}
-
{{CRLtemplate|PART IMAGE|Cod and Posterior Armor|
+
{{CRLtemplate|File:CLone cod and rear.jpg|Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}
-
{{CRLtemplate|PART IMAGE|Belt|
+
{{CRLtemplate|File:Clone Belt copy.jpg|Belt|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Ammo Belt with boxes and detonator.
Line 111: Line 121:
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}
-
{{CRLtemplate|PART IMAGE|Thigh Armor|
+
{{CRLtemplate|File:Clone thighs.jpg|Thigh Armor|
*Armor should be painted matte or satin white.  
*Armor should be painted matte or satin white.  
* Front of thigh armor should have a flat triangular area near the knee.  From the top of the triangle a ridge line should go up the front of the thigh to the top.
* Front of thigh armor should have a flat triangular area near the knee.  From the top of the triangle a ridge line should go up the front of the thigh to the top.
Line 119: Line 129:
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.}}
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.}}
-
{{CRLtemplate|PART IMAGE|Knee Armor|
+
{{CRLtemplate|File:Clone knees copy.jpg|Knee Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
*Knees should wrap around the front of the leg.  From top center a raised detail line should be present.
*Knees should wrap around the front of the leg.  From top center a raised detail line should be present.
Line 127: Line 137:
*Connection between the knee and the strapping should have a detail clip.}}
*Connection between the knee and the strapping should have a detail clip.}}
-
{{CRLtemplate|PART IMAGE|Lower Leg Armor|
+
{{CRLtemplate|File:Clone shins.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
Line 136: Line 146:
*Outside of the lower leg should have a pointed tip at the top and the inside of the lower leg should be rounded off at the top.}}
*Outside of the lower leg should have a pointed tip at the top and the inside of the lower leg should be rounded off at the top.}}
-
{{CRLtemplate|PART IMAGE|Boots|
+
{{CRL-cloneboots-realistic}}
-
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles. The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap. There should be no markings or labels from the shoe makers. | | }}
+
 
 +
{{CRLaccessories}}
-
{{CRLsubheading|Costume Accessories:}}
+
{{CRLdc15s-realistic}}
-
{{CRLtemplate|PART IMAGE|DC-15 Carbine Short Rifle|| | }}
+
{{CRLdc15a-realistic}}
-
{{CRLtemplate|PART IMAGE|DC-15 Long Rifle| | | }}
+
{{CRLfooter|CTN_CRL|T}}

Revision as of 20:22, 13 January 2013

crlblackhd.gif
Clone Trooper Sergeant
Missingprofile.jpg
Model MODEL NAME, Photo by PHOTOGRAPHER NAME


Clone-Trooper-Detachment.png

Description: Clone Trooper Sergeant
Prefix: TC
Detachment: Clone Trooper Detachment
Context: Episode II: Attack of the Clones
Clone troopers were an army of identical, genetically-modified clones of Jango Fett, created to serve in the Grand Army of the Republic during the conflict that came to be known as the Clone Wars. Cloned and raised in the cities of Kamino, the clone troopers trained and drilled since birth, and came to be regarded as one of the most efficient military forces ever to have existed in galactic history. This was not only due to their training, but also to their unwavering loyalty to the Galactic Republic and its leader, Supreme Chancellor Palpatine.

Please note that this costume is also eligible for membership in The Rebel Legion.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

  • This CRL is a work in progress.
  • This costume may be approved by GMLs, but until the library entry is complete, it is suggested that this character first be submitted to the appropriate DL/GML peer review section of the legion forum.
  • If you have this costume and would like to assist with the completion of this library entry, please contact your detachment leader.
  • Please note that the use of the word "should" below does not indicate that the armor piece is considered open to interpretation. All instances of "should be" and "should have" will be replaced with "is" and "has", as this guide is completed.
Required Costume Components

The following costume components are present and appear as described below.

Blankwhite.gif Sergeant Command Colors
For 501st approval:
  • In the CRL below you will see references to command colors/markings/paint.
  • For the sergeant, the command color is green.
  • Testors Go Green is an example of a suitable shade.
For level two certification (if applicable):
For level three certification (if applicable):


AOTC E2 Clone sergeantr helmet copy.jpg Helmet
For 501st approval:
  • Episode 2 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
  • Visor - Mirrored Chrome or Black Visor.
  • Helmet Fin on dome.
  • Rear fin needs a brake light cover installed.
  • 6 Primer Grey Vents on each side of helmet cheeks.
  • Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
  • Command marking symbolizing rank:
    • 1. The Tail fin should be painted to the dome of the helmet and contiuned down to the brow line
    • 2. The indented wrap around the dome above the brow should be painted in command coloring
    • 3. The visor area is outlined with command coloring
    • 4. A vertical stripe down the nose squaring off at the vocoder and wraping around to the neck ring should be painted in command coloring.
  • Ear holes may be painted light grey or remain white.
For level two certification (if applicable):
  • Helmet has the appearance of a neck ring.
For level three certification (if applicable):
  • Helmet has an enclosed complete neck ring that seals the helmet to the neck.
  • Rear fin light to be lit. Light is steady, does not blink, and is composed of 3 LEDs.
Clone trooper neck seal.jpg Neck Seal
For 501st approval:
  • Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.
For level two certification (if applicable):
For level three certification (if applicable):
TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.
For level two certification (if applicable):
For level three certification (if applicable):
AOTC clone sergeant shoulder bells copy.jpg Shoulder Bells
For 501st approval:
  • Armor should be painted matte or satin white.
    • Command paint follows the contour the the shoulder armor. Front should line should match upper arm location and rear shoulder line should match with rear upper arm line. The command stripe should be continuous from one part to the next.
  • Shoulders should be tear drop in shape with all rounded edges.
For level two certification (if applicable):
For level three certification (if applicable):
  • Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder.
Blankwhite.gif Upper Arm Armor
For 501st approval:
  • Armor should be painted matte or satin white.
    • Command paint semi covers some tricept indentation and 1/2" around the front of the bicep.
  • Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Elbow Armor
For 501st approval:
  • Armor should be painted matte or satin white.
    • Command paint covers the outside of the elbow and 1/2" - 3/4" of the return. The remainder is white.
  • There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
  • Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.
For level two certification (if applicable):
For level three certification (if applicable):
  • Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.
Blankwhite.gif Forearm Armor
For 501st approval:
  • Armor should be painted matte or satin white.
    • Command paint starts at the back of the bottom triangle of the forearm and continues in a straigh line to the top of the forearm. The top line starts 1/4" from compad location on right arm and continues in a vertical line. The area between these two lines should be filled in with command coloring. Match this to the left arm.
  • Both left and right forearms should be mirror images of each other.
  • Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectanular button.
  • Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):

For level three certification (if applicable):
  • Compad has detail antenna on its left.
  • Instead of a hard edge the top of the forearm has a bone ridge.
AOTC clone sergeant hand plates.jpg Hand Plates
For 501st approval:
  • Hand plates are mirror images of each other.
  • Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.
    • Handplates should be completely colored with command coloring.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin.
For level two certification (if applicable):
For level three certification (if applicable):
150px Chest Armor
For 501st approval:
  • Armor should be painted matte or satin white.
    • There should be 4 3/4" dots horitantal to the ground centered on the left breast in command coloring
  • Two detail slots on right breast.
  • Chest and back plate should match together at the sides with no gap, just a seam line.
  • Shoulder straps should be placed underneath the chest to connect to the back.
For level two certification (if applicable):

For level three certification (if applicable):
  • Shoulder straps should be slotted into the chest into the detail ridges of the top connection points.
Clone back.jpg Back Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
  • Chest and back plate should match together at the sides with no gap, just a seam line.
  • Shoulder straps should be placed underneath the chest to connect to the back.
For level two certification (if applicable):

For level three certification (if applicable):
  • Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
  • Highly detailed resin insert should replace softer details.
Clone abb2.jpg Ab Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
  • Ab section should wrap around the wearers body and be sealed at the sides or at the back.
  • Ab section should be completely contained under the chest and back armor.
For level two certification (if applicable):

For level three certification (if applicable):
  • Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.
CLone cod and rear.jpg Cod and Posterior Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Cod and Posterior armor should connect at the hips.
For level two certification (if applicable):
For level three certification (if applicable):
  • Hips should be connected via a snap with the correct detailed shape of the armor at the connection point.
Clone Belt copy.jpg Belt
For 501st approval:
  • Armor should be painted matte or satin white.
  • Ammo Belt with boxes and detonator.
  • Detonator is centered on the back of belt.
  • 8 boxes total, 4 on each side of abdomen and attached to the belt.
For level two certification (if applicable):

For level three certification (if applicable):
  • Belt Boxes should be notched and fitted flush with the details of the belt.
  • Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
  • Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
  • From the rear two belt boxes the belt should have a ribbed detailed appearance.
Clone thighs.jpg Thigh Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
  • Rear of the thigh should have an indention.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):

For level three certification (if applicable):
  • Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.
Clone knees copy.jpg Knee Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Knees should wrap around the front of the leg. From top center a raised detail line should be present.
  • Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
For level two certification (if applicable):

For level three certification (if applicable):
  • Center strap should be primer gray.
  • Connection between the knee and the strapping should have a detail clip.
Clone shins.jpg Lower Leg Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
  • Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
  • Calf can have an access area on the inside of the leg. The outside of the calf should be closed.
For level two certification (if applicable):

For level three certification (if applicable):
  • Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.
  • Outside of the lower leg should have a pointed tip at the top and the inside of the lower leg should be rounded off at the top.


Clone shoes copy.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle.
  • Boots are lace-less.
  • The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
  • There are no markings or labels from the shoe makers.
  • Boot soles are flat.
  • Boot soles are colored primer grey.


Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.


DC15 carbine.jpg DC-15S Blaster
For 501st approval:

Manufactured by BlasTech Industries the DC-15S is smaller in scale than the DC-15A blaster rifle. Although it has a shorter range than that of the "A" model, it is easier to handle with a higher rate of fire. It features a folding stock for braced firing.

  • Realistic Clone Style DC-15S Blaster.
  • Blaster may be scratch built out of plastic, wood, metal or cast in resin.
  • Blaster has realistic Episode II or Episode III details:
    • Wire frame sight.
    • Folding stock.
    • (12) radiator fins evenly spaced along the length of barrel.
    • Igniter detail knobs.
    • Charge magazine clip on right side.
  • Total length is approximately 26“ (66 cm).
  • Because of the scale, the Hasbro version is incorrect.
For level two certification (if applicable):
  • Charge magazine detail on clip is metal to gun metal grey in color.
  • Detail bolts and screws are metal to gun metal grey in color.
  • Igniter knobs have some copper coloring.
  • Blaster is weathered.
For level three certification (if applicable):
  • Functioning Blue LED is installed in barrel.


DC15 rifle.jpg DC-15A Blaster Rifle
For 501st approval:

Manufactured by BlasTech Industries, the DC-15A is a tibanna gas, cartridge powered weapon. Hyper-ionized blue plasma bolts are more than capable of penetrating armored units. Exceptionally effective against both droids and contemporary targets.

  • Realistic Clone Style DC-15A Blaster Rifle.
  • Blaster rifle is scratch built out of plastic, wood, metal or cast in resin.
  • Blaster has realistic Episode II or Episode III details:
    • Flip up sight in down position.
    • (10) radiator fins evenly spaced along the length of barrel.
    • Power setting adjuster detail lever.
    • Sniper Scope attached under rifle in storage position.
    • Charge magazine clip on left side.
    • Igniter detail knobs.
  • Total length is approximately 55 inches (139.7 cm).
  • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • Charge magazine detail on clip is metal to gun metal grey in color.
  • Detail bolts and screws are metal to gun metal grey in color.
  • Igniter has some copper coloring.
  • Power setting adjuster detail lever is metal or gun metal grey.
  • Sniper scope is metal or gun metal grey.
  • Blaster is weathered.
For level three certification (if applicable):
  • Functioning Blue LED is installed in barrel.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:TC_sergeant

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.