Revision as of 21:49, 3 June 2011 by Stormtrooperguy (Talk | contribs)
crlblackhd.gif
Clone Trooper
500px
Model MODEL NAME, Photo by PHOTOGRAPHER NAME


Clone-Trooper-Detachment.png

Description: Clone Trooper
Prefix: TC
Detachment: Clone Trooper Detachment
Context: The Clone Wars, seasons 1-3
Clone troopers were an army of identical, genetically-modified clones of Jango Fett, created to serve in the Grand Army of the Republic during the conflict that came to be known as the Clone Wars. In the Clone Wars animated series, these troopers wear a stylized version of the Attack of the Clones armor.


Template:CRLwipapproval

Required Costume Components

The following costume components are present and appear as described below.


TC animated helmet.jpg Helmet
For 501st approval:
  • Phase I animated style helmet.
    • Movie style helmets are not combined with animated armor.
  • Helmet is painted matte or satin white.
  • Narrow fin on dome.
  • Black eye lens extends down through the entire frown area.
  • Raised bump at each ear, 1" - 1.25" in diameter.
  • (4) Vents on each side of helmet.
    • Vents may be painted black or grey, or cut out and filled with black mesh.
  • Primer grey stripe around back of dome.
  • Raised white circle at the back center of the helmet.
  • Rectangular indent at the back center of the helmet may be primer grey or heavily weathered white.
  • Armor is weathered with shades of grey.


Blankwhite.gif Neck Seal
For 501st approval:
  • Neck seal to be black in color with no ribbing. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.
For level two certification (if applicable):
  • Neck seal should close via 2 small black snaps in the front.
For level three certification (if applicable):


TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


Blankwhite.gif Shoulder Bells
For 501st approval:
  • Armor should be painted matte or satin white.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Upper Arm Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Should have a notch on the lower area of the back of the arm that matches up with the elbow armor.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Forearm Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Left forearm should have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess should be closest to the elbow.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
  • Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
For level two certification (if applicable):
For level three certification (if applicable):


TC animated handplates.jpg Hand Plates
For 501st approval:
  • Armor is painted matte or satin white.
  • Hand plates are mirror images of each other.
  • Hand plates have an angled peak that comes to a point over the index or middle finger, just past the main knuckle of the hand.
  • Armor is weathered with shades of grey.


Blankwhite.gif Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin.
For level two certification (if applicable):
For level three certification (if applicable):


TC animated chest.jpg Chest Armor
For 501st approval:
  • Animated Phase I Chest Armor.
  • Armor is painted matte or satin white.
  • Lower portion of the chest has a curved notch for the abdomen armor to fit into.
  • Chest and Back Armor match together at the sides and shoulders with no open gap.
    • A seam line is present.
  • Shoulder straps are placed over the chest and back armor at the seams.
  • Armor is weathered with shades of grey.



TC animated back.jpg Back Armor
For 501st approval:
  • Animated Phase I Back Armor.
  • Armor is painted matte or satin white.
  • Rear center of back armor has detailed area that contains a O11 pattern.
  • Shoulder straps are placed over the Back and Chest armor at the seams.
  • Armor is weathered with shades of grey.


Blankwhite.gif Ab Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Top edge of the armor is curved to match the chest.
  • The ab armor protrudes out in the middle to better up with the chest.
  • 4 inset lines divide the ab plate into segments.
For level two certification (if applicable):
For level three certification (if applicable):


TC animated cod.jpg Codpiece and Belt front
For 501st approval:
  • Armor is painted matte or satin white.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • The front segments have a key/slot detail.
  • Belt boxes are mounted at the hips.
  • Codpiece and Posterior armor connect at the hips.
    • Butted seams are permitted at this connection if required.
  • Armor is weathered with shades of grey.



TC animated butt.jpg Posterior Armor, Belt rear and Detonator
For 501st approval:
  • Armor is painted matte or satin white.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • Posterior armor and Codpiece connect at the hips.
    • Butted seams are permitted at this connection if required.
  • Detonator is centered on the back of belt.
    • Detonator has no control buttons.
    • The detonator has (2) lines set in approx 1/2" - 5/8" from the edges.
      • Lines may be recessed or painted on
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Detonator lines are recessed.
Blankwhite.gif Belt Boxes
For 501st approval:
  • Armor should be painted matte or satin white.
  • 2 rectangular boxes are mounted at the hips. The top edge of the box is tapered town toward the outside. There is an inset detail near the top of each box.
For level two certification (if applicable):
For level three certification (if applicable):


TC animated thighs.jpg Thigh Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Front of thigh armor has a flat triangular area near the knee with a notch cut out for the knee armor.
  • From the top of the triangle a ridge line travels up the front of the thigh to the top edge.
  • The upper outer edge has an angled section.
  • The armor is weathered with shades of grey.
For level two certification (if applicable):
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
Blankwhite.gif Lower Leg Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Knee armor is integrated with the lower leg
  • The armor should have a flat center triangle below the knee plate, with the single point facing downward.
  • The calf detail of the armor has a ridge wrapping around the back of the leg.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
  • Boots have a center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap.
For level two certification (if applicable):
For level three certification (if applicable):
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.


CRLdc15s-animated.jpg DC-15S Blaster Carbine (animated style)
For 501st approval:

Manufactured by BlasTech Industries, this weapon is commonly carried by the Troopers of the Galactic Republic.

  • This is the animated variant of the DC-15S blaster rifle.



Dc15a Animated.jpg DC-15A Blaster Rifle (animated style)
For 501st approval:

Manufactured by BlasTech Industries, this blaster is the standard issue weapon carried by the Clone Troopers of the Grand Army of the Republic.

  • This is the animated variant of the DC-15A blaster rifle.


Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.