Revision as of 21:29, 20 April 2011 by Stormtrooperguy (Talk | contribs)
crlblackhd.gif
Clone Trooper
500px
Model MODEL NAME, Photo by PHOTOGRAPHER NAME


Clone-Trooper-Detachment.png

Description: Clone Trooper
Prefix: TC
Detachment: Clone Trooper Detachment
Context: The Clone Wars, seasons 1-3
Clone troopers were an army of identical, genetically-modified clones of Jango Fett, created to serve in the Grand Army of the Republic during the conflict that came to be known as the Clone Wars. In the Clone Wars animated series, these troopers wear a stylized version of the Attack of the Clones armor.


This CRL is a work in progress and is not yet ready to use for GML approval!

Costume Components
Blankwhite.gif Helmet
For 501st approval:
  • Clone Wars style Clone Helmet.
  • Black visor, extending down through the frown area.
  • Narrow fin on dome.
  • 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
  • Primer grey stripe around back of dome.
  • White circle and rectangular indent at the back of the helmet.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Neck Seal
For 501st approval:
  • Neck seal to be black in color with no ribbing. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.
For level two certification (if applicable):
  • Neck seal should close via 2 small black snaps in the front.
For level three certification (if applicable):
TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Shoulder Bells
For 501st approval:
  • Armor should be painted matte or satin white.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Upper Arm Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Should have a notch on the lower area of the back of the arm that matches up with the elbow armor.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Forearm Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Left forearm should have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess should be closest to the elbow.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
  • Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Hand Plates
For 501st approval:
  • Armor should be painted matte or satin white
  • Hand plates are mirror images of each other.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Chest Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Chest and back plate should match together at the sides and shoulders with no gap, just a seam line.
  • Shoulder straps should be placed over the chest and back armor at the seams.
  • Lower portion of the chest has a curved notch for the abdomen armor to fit into.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Back Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper.
  • Shoulder straps should be placed over the chest and back armor at the seams.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Ab Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
  • Ab section should wrap around the wearers body and be sealed at the sides or at the back.
  • Ab section should be completely contained under the chest and back armor.
For level two certification (if applicable):

For level three certification (if applicable):
  • Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.
Blankwhite.gif Cod and Posterior Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Cod and Posterior armor should connect at the hips.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Belt
For 501st approval:
  • Armor should be painted matte or satin white.
  • Belt is approx 3" tall and divided into 1.75" wide segments. The front segments have a key/slot detail.
  • 2 rectangular boxes are mounted at the hips. The top edge of the box is tapered town toward the outside. There is an inset detail near the top of each box.
  • Detonator is centered on the back of belt with no control buttons or other detailing.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Thigh Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Lower Leg Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Knee armor is integrated with the lower leg
  • The armor should have a flat center triangle below the knee plate, with the single point facing downward.
  • The calf detail of the armor has a ridge wrapping around the back of the leg.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
  • Boots have a center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap.
For level two certification (if applicable):
For level three certification (if applicable):
Costume Accessories:


Blankwhite.gif DC-15A Blaster Rifle (animated style)
For 501st approval:

This is the animated variant of the DC-15A blaster rifle. Manufactured by BlasTech Industries, this blaster is the standard issue weapon carried by the Clone Troopers of the Grand Army of the Republic.



CRLdc15s-animated.jpg DC-15S Blaster Carbine (animated style)
For 501st approval:

This is the animated variant of the DC-15S blaster rifle. Manufactured by BlasTech Industries, this weapon is commonly carried by the Troopers of the Galactic Republic.


Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.