501st Legion: Vader's Fist

(Difference between revisions)

Revision as of 19:34, 20 April 2011

Clone Trooper

Model MODEL NAME, Photo by PHOTOGRAPHER NAME

Description: Clone Trooper
Prefix: TC
Detachment: Clone Trooper Detachment
Context: The Clone Wars, seasons 1-3
Clone troopers were an army of identical, genetically-modified clones of Jango Fett, created to serve in the Grand Army of the Republic during the conflict that came to be known as the Clone Wars. In the Clone Wars animated series, these troopers wear a stylized version of the Attack of the Clones armor.

This CRL is a work in progress and is not yet ready to use for GML approval!

Costume Components

	Helmet For 501st approval: Clone Wars style Clone Helmet. Visor - Black Visor, extending down through the frown area Helmet Fin on dome. 4 Vents on each side of helmet cheeks. May be painted black or grey, or cut out and filled with black mesh. Primer grey stripe around back of dome.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Neck Seal For 501st approval: Neck seal to be black in color with no ribbing. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.
	For level two certification (if applicable): Neck seal should close via 2 small black snaps.
	For level three certification (if applicable):

	Under Suit For 501st approval: Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Shoulder Bells For 501st approval: Armor should be painted matte or satin white.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Upper Arm Armor For 501st approval: Armor should be painted matte or satin white. Should have a notch on the lower area of the back of the arm that matches up with the elbow armor. Armor should be seamless. No visible traces of how the armor was assembled should be shown.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Forearm Armor For 501st approval: Armor should be painted matte or satin white. Left forearm should have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess should be closest to the elbow. Armor should be seamless. No visible traces of how the armor was assembled should be shown. Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Hand Plates For 501st approval: Armor should be painted matte or satin white Hand plates are mirror images of each other.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Gloves For 501st approval: Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Chest Armor For 501st approval: Armor should be painted matte or satin white. Chest and back plate should match together at the sides and shoulders with no gap, just a seam line. Shoulder straps should be placed over the chest and back armor at the seams. Lower portion of the chest has a curved notch for the abdomen armor to fit into.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Back Armor For 501st approval: Armor should be painted matte or satin white. Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper. Shoulder straps should be placed over the chest and back armor at the seams.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Ab Armor For 501st approval: Armor should be painted matte or satin white. Four 1/4" diameter holes per side on indents of ab plate, eight holes total. Ab section should wrap around the wearers body and be sealed at the sides or at the back. Ab section should be completely contained under the chest and back armor.
	For level two certification (if applicable):
	For level three certification (if applicable): Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.

	Cod and Posterior Armor For 501st approval: Armor should be painted matte or satin white. Cod and Posterior armor should connect at the hips.
	For level two certification (if applicable):
	For level three certification (if applicable): Hips should be connected via a snap with the correct detailed shape of the armor at the connection point.

	Belt For 501st approval: Armor should be painted matte or satin white. Ammo Belt with boxes and detonator. Detonator is centered on the back of belt. 8 boxes total, 4 on each side of abdomen and attached to the belt.
	For level two certification (if applicable):
	For level three certification (if applicable): Belt Boxes should be notched and fitted flush with the details of the belt. Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right. Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left. From the rear two belt boxes the belt should have a ribbed detailed appearance.

	Thigh Armor For 501st approval: Armor should be painted matte or satin white. Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top. Rear of the thigh should have an indention. Armor should be seamless. No visible traces of how the armor was assembled should be shown.
	For level two certification (if applicable):
	For level three certification (if applicable): Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.

	Lower Leg Armor For 501st approval: Armor should be painted matte or satin white. Knee armor is integrated with the lower leg The armor should have a flat center triangle below the knee plate, with the single point facing downward. The calf detail of the armor has a ridge wrapping around the back of the leg.
	For level two certification (if applicable):
	For level three certification (if applicable):

	Boots For 501st approval: White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles. Boots have a center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap.
	For level two certification (if applicable):
	For level three certification (if applicable):

Costume Accessories:

	Animated style DC-15A Short Rifle For 501st approval:
	For level two certification (if applicable):
	For level three certification (if applicable):

	Animated style DC-15 Long Rifle For 501st approval:
	For level two certification (if applicable):
	For level three certification (if applicable):

Retrieved from "http://www.501st.com/databank/Costuming:TC_CW-animated_grunt"

Revision as of 19:34, 20 April 2011

NAVIGATION

Operations Docs

Membership

Personal tools

Search

Toolbox