Revision as of 03:06, 15 June 2014 by TK826 (Talk | contribs)
crlblackhd.gif
Coruscant Guard - Phase 1
Missingprofile.jpg
Model MODEL NAME, Photo by PHOTOGRAPHER NAME


Clone-Trooper-Detachment.png

Description: Coruscant Guard - Phase 1
Prefix: TC
Detachment: Clone Trooper Detachment
Context: The Clone Wars, seasons 1-3

The Coruscant Guard operate the Diplomatic Escort Group which is charged with protecting diplomats on key missions.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

  • This CRL is a work in progress.
  • This costume may be approved by GMLs, but until the library entry is complete, it is suggested that this character first be submitted to the appropriate DL/GML peer review section of the legion forum.
  • If you have this costume and would like to assist with the completion of this library entry, please contact your detachment leader.
  • Please note that the use of the word "should" below does not indicate that the armor piece is considered open to interpretation. All instances of "should be" and "should have" will be replaced with "is" and "has", as this guide is completed.
Required Costume Components

The following costume components are present and appear as described below.

Blankwhite.gif Helmet
For 501st approval:
  • Clone Wars style helmet.
    • Movie style helmets cannot be combined with animated armor.
  • Helmet is painted matte or satin white.
  • A dark scarlet line, about 1 inch wide, is painted above the brow of the eye lens, from left to right.
  • A dark scarlet diamond is painted in the center of the forehead area, from the brow of the eye lens and ends just at the start of the fin.
  • A dark scarlet inverted triangle is painted below the eye lens, extending on either side of the "center" of the helmet down the sides about halfway.
  • The ear caps on the left and rights sides of the helmet are painted matte or satin white and weathered.
  • A black visor extends down through the entire frown area.
  • Narrow fin on dome.
  • Raised bump at each ear, 1" - 1.25" in diameter.
  • 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
  • A grey stripe runs around back of dome.
  • Raised satin white circle at the back of the helmet.
  • Rectangular indent at the back of the helmet shall be black or heavily weathered grey.
  • Armor is weathered with shades of grey.


|


TC animated neckseal.jpg Neck Seal
For 501st approval:
  • Neck seal is black in color with no ribbing.
  • No logos or labels are visible.
    • If the seal is not incorporated as part of the under suit, a balaclava or other similar covering is acceptable.
For level two certification (if applicable):
  • Neck seal closes in the front via 2 small black snaps.


TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


Blankwhite.gif Shoulder Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • The edges of the shoulders are outlined by a dark scarlet line.
    • The line is about 2 inches wide along the bottom of the shoulder and about 1 inch wide around the rest of the shoulder.
  • Armor is weathered with shades of grey.


Blankwhite.gif Upper Arm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • On the back of the biceps, there is what appears to be a dark scarlet upsidedown "Y".
  • Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
  • Armor is be seamless.
    • No visible traces of how the armor was assembled are shown.
  • Armor is weathered with shades of grey.


Blankwhite.gif Forearm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Left forearm has a compad with 4 main square recessed areas and 1 slightly smaller square recessed area.
    • The smaller recess is closest to the elbow.
  • Armor is seamless on the outside edge.
    • Due to the shape of the armor, a butted seam is acceptable on the inside if required.
  • Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
  • Elbow plate is painted matte or satin white.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
Blankwhite.gif Hand Plates
For 501st approval:
  • Armor is painted matte or satin white.
  • Hand plates are mirror images of each other.
  • Armor is weathered with shades of grey.



Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
  • Gloves cover any exposed skin.
  • Gloves do not show any labels or logos when the armor is worn.


Blankwhite.gif Chest Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Lower portion of the chest has a curved notch for the abdomen armor to fit into.
  • The Symbol of the Galactic Senate is painted in dark scarlet on the center of chest, with the center of the symbol at the top of the curved notch.
  • Extending out from the Senate symbol is a dark scarlet line that moves towards the back armor and expands in size. The line sits under the breast portion of the armor.
  • Chest and back plate match together at the sides and shoulders with no open gap.
    • Butted seam lines are permitted if required.
  • Shoulder straps are placed over the chest and back armor at the seams.
    • Shoulder straps are painted matte or satin white.
  • Armor is weathered with shades of grey.


Blankwhite.gif Back Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • A two-inch dark scarlet stripe extends from the chest below the arm and ending just on either side of the rear tank.
  • Rear tank has detailed area that contains a O11 pattern.
  • Shoulder straps are placed over the chest and back armor at the seams.
    • Shoulder straps are painted matte or satin white..
  • Armor is weathered with shades of grey.


Blankwhite.gif Abdomen Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • The Abdomen armor has the bottom portion of the Galactic Senate symbol in the center, extending down the abs to the belt.
  • Armor is weathered with shades of grey.



TC animated grunt kidney.jpg Kidney Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Kidney and abdomen armor connect at the sides with no open gap.
    • A butted seam between the kidney and abdomen armor is acceptable.
  • Armor is weathered with shades of grey.



TC animated cod.jpg Codpiece and Belt front
For 501st approval:
  • Armor is painted matte or satin white.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • The front segments have a key/slot detail.
  • Belt boxes are mounted at the hips.
  • Cod and Posterior armor are connected at the hips.
    • Butted seams are permitted at this connection if required.
  • Armor is weathered with shades of grey.



TC animated butt.jpg Posterior Armor, belt rear and detonator
For 501st approval:
  • Armor is painted matte or satin white.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • Codpiece and Posterior armor connect at the hips.
    • Butted seams are permitted at this connection if required.
  • Detonator is centered on the back of belt.
    • Detonator has no control buttons.
    • The detonator has 2 lines set in approx 1/2" - 5/8" from the edges.
      • Lines may be recessed or painted on
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Detonator lines are recessed.


TC animated belt box.jpg Belt Boxes
For 501st approval:
  • Two rectangular boxes are mounted at the hips.
  • Boxes are painted matte or satin white.
    • The top side of the box is tapered outward.
    • There is an inset detail near the top of each box.
  • Armor is weathered with shades of grey.



TC animated thighs.jpg Thigh Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Front of thigh armor has a flat triangular area near the knee with a notch cut out for the knee armor.
  • From the top of the triangle a ridge line travels up the front of the thigh to the top edge.
  • The upper outer edge has an angled section.
  • The armor is weathered with shades of grey.
For level two certification (if applicable):
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
Blankwhite.gif Lower Leg Armor
For 501st approval:
  • Armor is painted matte or satin white with a dark scarlet stripe that wraps around the calf about 2" below the top of the armor and continues down the front center of the armor.
  • Knee armor is integrated with the lower leg.
    • Knee area is painted matte or satin white.
    • Knee section has an inverted dark scarlet triangle painted down the center.
  • The armor has a flat center triangle below the knee plate, with the single point facing downward.
  • The calf detail of the armor has a ridge wrapping around the back of the leg.
    • Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin.
  • Armor is weathered with shades of grey.



TC animated boots.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area.
  • Boots are lace-less and have flat soles.
  • Boots have a center strip running from the toe to the ankle.
  • A strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap.
For level two certification (if applicable):
  • Boots have accurate notched sole.
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.


CRLdc15s-animated.jpg DC-15S Blaster Carbine (animated style)
For 501st approval:

Manufactured by BlasTech Industries, this weapon is commonly carried by the Troopers of the Galactic Republic.

  • This is the animated variant of the DC-15S blaster rifle.



Dc15a Animated.jpg DC-15A Blaster Rifle (animated style)
For 501st approval:

Manufactured by BlasTech Industries, this blaster is the standard issue weapon carried by the Clone Troopers of the Grand Army of the Republic.

  • This is the animated variant of the DC-15A blaster rifle.


This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:TC_-_Coruscant_Guard_phase_1

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.