Description: Darth Tyranus / Count Dooku, The Clone Wars, Sleepwear
Prefix: SL
Detachment: Sith Lord Detachment
Context: Star Wars: The Clone Wars, Season 3 Episode 12.
Mother Talzin, leader of the Nightsisters, veils Asajj and her fellow assassins in a cloak of invisibility, and they infiltrate Dooku's palace on Serenno. Though they fail to kill the Count, their attack reveals the Count's stylish sleepwear.

From starwars.com: "So, Dooku sports the finest silk easy-fit trousers and a matching side-opening silk blouson in dark gray-blue with a midnight blue collar and sash," says Plunkett. "His front pocket is monogrammed and the sleeves are accented by finely embroidered patterning running down their sides. The ensemble is finished off with hand-stitched kid leather charcoal moccasins. Available in three sizes: Old, Angry and Angry Old."

The 501st approval requirements are listed in black.

The Sith Lord Detachment defines additional, optional levels of costuming excellence. In the page below, items listed under "For level two certification" are recommended features that will greatly improve the quality of the costume. These items are not required for 501st membership, but are highly recommended. Items listed under "For level three certification" are some of the highest level accuracy features for those who strive to be screen accurate. These items are also not required for 501st membership.

Also note that these two additional "certification levels" DO NOT correspond to the Advanced Standards program of the Sith Lord Detachment, and you are encouraged to visit the Sith Lord Detachment Forum for more information.

For 501st membership, only the requirements in black need to be met.

• This CRL is a work in progress.
• While this costume must be approved by the Legion Membership Officer, submissions should still go to the local GML, who will post the application in the appropriate section of the Legion forum.
• If you have this costume and would like to assist with this CRL, please contact your detachment leader!
• Please note that the use of the word "should" below does not indicate that a requirement is optional. All instances of should will be replaced with must as this guide is completed.

The following costume components must be present and appear as described below for approval .

• The hair is not parted. It is combed straight back from a slight widow's peak at the front.
• At the sides, the hair curves around until it is parallel with the sideburns.
• In the back, the hair is off of the neck. Hair should be colored or dyed white.
  

• You can either use your own facial hair, or high quality costuming facial hair.
• The moustache covers the area between the nose and lips, then tapers off past the edge of the lips and joins into the beard.
• Beard is full and (Optional) extends to a point at the chin. It tapers slightly as it goes up the sides of the face until it meets the sideburns.
• Facial hair should be colored or dyed white.
  

• Dark Grey-Blue fine silk or silk-like material in a wrap around style.
• A snap or other attachment method can be used at the meeting point of the collars.
• The material should not be shiny, but dull in appearance.
• Lining should be dark midnight blue that extends to become the collar.
  

• The shoulders and sleeves should have an accurate pattern either embroidered or screen printed as shown in the pictures.
  

• Left chest pocket should have accurate monogram either screen printed or embroidered as shown in the pictures.
• Pocket comes to a point in the middle of the bottom.
  

• The sash is approximately 3-4 inches in width and made of the same material and dark blue color as the collar/lining.
• Sash wraps around the waist and ties on the wearer’s right hip.
• Sash should be long enough to wrap around, tie, and hang to approximately mid thigh.
  

• The pants are made of the same dark grey-blue material as the shirt/tunic and lined with the same dark blue material of the collar/sash.
• The pants are undecorated with a crease down the front of the legs.
• The pants are hemmed at the ankle.
  

• These should be made of a charcoal grey leather/leather-like material.
• The soles should be black and have no discernable heel.
• The seam lines of the CGI model should be followed as shown in the pictures.
  

Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.

• A MR, scratch built, or another high-end prop replica of what is in the film.
• The lightsaber should only be required as long as it's in compliance with the applicant’s local laws.
  

• Must reflect 1:1 scale in size and must appear to be of metal or chrome stock.

• A Covertec clip is present to secure the lightsaber.
• It is attached to the belt on the wearer's left hip.