Description: Darth Tyranus/Count Dooku, Revenge of the Sith
Prefix: SL
Detachment: Sith Lord Detachment
Context: Episode III: Revenge of the SIth
The leader of the Confederacy of Independent Systems and Sith apprentice to Darth Sidious. The waning power of the CIS is reflected in the fading colours of this Sith Lord's attire.

See also: AOTC Tyranus

The 501st approval requirements are listed in black.

The Sith Lord Detachment defines additional, optional levels of costuming excellence. In the page below, items listed under "For level two certification" are recommended features that will greatly improve the quality of the costume. These items are not required for 501st membership, but are highly recommended. Items listed under "For level three certification" are some of the highest level accuracy features for those who strive to be screen accurate. These items are also not required for 501st membership.

Also note that these two additional "certification levels" DO NOT correspond to the Advanced Standards program of the Sith Lord Detachment, and you are encouraged to visit the Sith Lord Detachment Forum for more information.

For 501st membership, only the requirements in black need to be met.

The following costume components must be present and appear as described below for approval .

• The hair is not parted.
• It is combed straight back from a slight widow's peak at the front. At the sides, the hair curves around until it is parallel with the sideburns. In the back, the hair is off of the neck.
• The hair is colored or dyed white
  

• The eyebrows should be dark grey in color.

• You can either use your own facial hair, or high quality costuming facial hair.
• The mustache covers the area between the nose and lips, then tapers off past the edge of the lips and joins into the beard.
• Beard is trimmed closely to the chin and side of the face. It tapers slightly as it goes up the sides of the face until it meets the sideburns. Facial hair should be colored or dyed white.
  

• The mustache and under the lower lip should be dark grey in color.
• Should have bags under the eyes, wrinkles, and liver spots to match film reference. Visit the Count Dooku facial details page for reference.

• To be most accurate the beard should be trimmed and colored to match Christopher Lee's in the movie.

• Made of medium brown, non-glossy fabric, wool or wool-equivalent material.
• The cloak is fully lined with a satin-weave material that is a lighter brown than the cloak itself. It falls from the shoulders to just below the calves.
• The upper portion of the cloak has front and back yolks with vertical lightly padded quilt lines. These run from the front to the back of the cloak at armpit level vertically, with one from the neck to the shoulder horizontally.
• The back of the cloak collar sits slightly higher than the tunic collar in the back.
  

• The cape should be made of wool in the appropriate color; Revenge of the Sith has a medium brown cloak with a lighter rustic-colored lining of a velvet/velour fabric.
• The neck of the cape should come to a "peek" in the back, covering the back collar of the person's neck.

• There should be exactly 9 quilt lines running over each shoulder.

• Two silver-colored round "Victorian" style brooches, 2–3" in diameter (measurement given for proportional dimensions only).
• These can be made from metal pins, or metallic spray-painted wood, resin, or plastic.
• They attach above the horizontal seam on the cloak and near the edge of the cloak.
  

• Clasps should reflect similar Victorian-clover design in the picture.

• The clasps should attach between the first and second quilt line from the center of the chest.

• Silver metallic chain with oval-shaped links. It hangs flat and horizontally across the upper chest, and is fastened by the clasps just below the collarbone.
  

• It should be taunt and not hang down.

• It should be 13 links alternating from the claps with one smaller link to two larger over-lapping links.

• Requirements of the tunic are the same as the IOC's officer-style tunic with the following exceptions:
• It is made of a dark brown material.
• The collar is ~ 2" in height with a no gap (modesty panel may be used).
• The bottom of the tunic falls 4–5" below the waist (measurements given for proportional dimensions only).
• The double-breasted section and rest of the bottom of the tunic align along the bottom edge.
  

• The tunic should be made of a gabardine fabric, which is dark brown in color.
• The tunic should not have code cylinder pockets.
• There should be a dart running ~4" below the collar on the center of the jacket.

• The base belt is brown leather or leather-like material, 2" wide (measurement given for proportional dimensions only) and has two "buckles", one on each side.
• Each buckle is made of brown leather, and is slightly wider than the belt itself.
• Belt buckles have 5 horizontal, overlapping leather strips at equal intervals.
  

• The top of each strip should be under the strip above it, so they appear over-lapping.

• The belt should be made from quality, unblemished, leather.

• Dark brown, similar to officer-style pants or trousers that is made from the same fabric as the tunic.
• The pants tuck into the boots.
• Loose fitting straight legged pants that are bloused at the top of the boots.
• Optional: Jodhpurs style pants are also acceptable.
  

• The trousers should be made of a gabardine fabric matching the tunic.

• Pant legs should have a slight jodhpurs flare.

• Black lace-less boots with rounded toe that are either leather or leather like material with a medium gloss shine.
• Boots do not have any buckles or adornments.
• They come up to just below knee level.
• Optional: A boot that zips up on the inside of the leg is also acceptable.
  

• They should be Equestrian-styled black, leather boots, reaching just below the knee.

• Should be the "slip on" style and not contain zippers or decoration.

• A MR, scratch built, or another high-end prop replica of what is in the film.
• The lightsaber should only be required as long as it's in compliance with the applicant’s local laws.
  

• Must reflect 1:1 scale in size and must appear to be of metal or chrome stock.

• A rectangular Covertec clip as seen in the picture is present to secure the lightsaber.
• It is attached to the belt on the wearer's left hip.
• The Hasbro or circular/oval Covertec clips will not be approved.