Revision as of 22:05, 5 October 2011 by Stormtrooperguy (Talk | contribs)
crlblackhd.gif
Juno Eclipse, Rogue Shadow
Missingprofile.jpg
Model ', Photo by '


Imperial-Officer-Corps.png

Description: Juno Eclipse, Rogue Shadow
Prefix: ID
Detachment: Imperial Officer Corps
Context: The Force Unleashed


The 501st approval requirements are listed in black.

The Imperial Officer Corp Detachment defines additional, optional levels of costuming excellence. In the page below, items listed in blue are optional features that will improve the quality of the costume. These items are not required, but are recommended.

For 501st membership only the requirements in black need to be met.


  • This CRL is a work in progress.
  • While this costume must be approved by the Legion Membership Officer, submissions should still go to the local GML, who will post the application in the appropriate section of the Legion forum.
  • If you have this costume and would like to assist with this CRL, please contact your detachment leader!
  • Please note that the use of the word "should" below does not indicate that a requirement is optional. All instances of should will be replaced with must as this guide is completed.

Required Costume Components

The following costume components must be present and appear as described below for approval .


ID hat black.jpg Imperial Hat, black
For 501st approval:
  • Fabric should be a medium weight suiting material exactly matching the pants and tunic if applicable. Gabardine style weave is most accurate.
  • Base of the hat should be conical, with a crown about 4" (101.6 mm) tall.
  • Front and rear "flaps" should overlap on the sides and be about 4" (101.6 mm) high.
  • Front bill extends 3" down, decorated with 6 or 7 concentric stitches.
  • Imperial Code Disk (see below) positioned in the center of the front vertical "flap."
For level two certification (if applicable):
  • Code disk should have a notch detail on the outermost disk.
For level three certification (if applicable):
  • Code disk should exactly match screen-used prop.
ID juno hair.jpg Hair Style
For 501st approval:
  • Hair must be blonde. This can be achieved via natural hair color or a wig.
  • Worn in a French twist.
  • Hair style and color must match published images.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Jacket/Tunic
For 501st approval:
  • Waist length, fitted officer-like black jacket with high collar.
  • Breast panels present but folded back (or made to give the appearance of being folded back.
  • 3/4-length sleeves
  • Tailored via 2 princess seams in the back.
For level two certification (if applicable):
For level three certification (if applicable):
ID juno rank.jpg Rank Bar
For 501st approval:
  • Worn on the left side of the tunic over the heart.
  • Rank consists of colored plastic tiles mounted on metal bar.
  • Rank tiles are 4 amber and 2 red (from left to right), made of some type of plastic (i.e. plexiglass, acrylic, etc.)
  • Yellow tiles are not acceptable.
  • Rank tile dimensions are approx. 1/2" (12.7 mm)width x 3/4" (19 mm) height and about 1/8" (3.2 mm).
  • Tiles should be mounted with approx. 1/4" (6.4 mm) spaces between them.
For level two certification (if applicable):
For level three certification (if applicable):
Generic-code-cylinders.jpg Code Cylinders
For 501st approval:
  • 2 code cylinders, one on each side of the tunic.
  • Chalk-holder/dosimeter style only: silver tube with short clip, top should be colored blue.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Grey Tank Top
For 501st approval:
  • Grey tank top style undershirt worn under the tunic.
For level two certification (if applicable):
For level three certification (if applicable):


ID belt.jpg Belt
For 501st approval:
  • The belt shall be constructed from a non-textured leather or a leather-like material.
    • Approximately 2" (50.8 mm) in width, up to 3" (76.2 mm) is acceptable.
    • There are no loops on the belt.
  • A single large snap or rivet should be visible approximately 1" (25.4 mm) from the buckle.
    • The belt may be worn with the snap to the right or left of the wearer.
  • The buckle shall be constructed from a horizontally brushed metal, or metal looking material.
  • The buckle size should be approximately 2 5/8" (66.7 mm) high and 4 1/8" (104.5 mm) wide with 0.5" (12.7 mm) radius rounded corners.
    • Please refer to the Imperial Buckle reference page for information on accurate and inaccurate style buckles.
  • Buckles are adorned with an Imperial Code Disk at the center.
For level two certification (if applicable):
  • Belt must be made of leather.
  • Snap is to be worn to the left of the wearer.
  • Buckle shall have a slight horizontal curve.
For level three certification (if applicable):
ID juno gloves.jpg Gloves
For 501st approval:
  • Open back, full-fingered driver gloves

For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Leggings
For 501st approval:
  • Fitted black trousers (made from a stretch material)
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Boots
For 501st approval:
  • Fitted, knee high black leather or leather like boots.
  • Low heel only.
  • Rubber boots not acceptable.
For level two certification (if applicable):
For level three certification (if applicable):
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.