(Difference between revisions)
(34 intermediate revisions not shown)
Line 1: Line 1:
-
{{CRLheader|Imperial Officer|File:Blankwhite.gif|MODEL NAME|PHOTOGRAPHER NAME}}
+
{{CRLheader|Imperial Line Officer (olive)|File:ID_Line_Officer_Full.jpg|ID-5955|BJ Savage}}
-
{{CRLdetinfo| 1108 |Imperial Officer|ID|Star Wars Episodes IV - IV and Expanded Universe| }}
+
{{CRLdetinfo| 1108 |Imperial Line Officer|ID|Star Wars Episodes IV - IV and Expanded Universe| }}
{{CRLioclevels}}
{{CRLioclevels}}
-
{{CRLwipapproval}}
+
{{CRLgmlapproval}}
-
{{CRLsubheading|Costume Components}}
+
{{CRLrequirements}}
 +
{{CRLgreyimperialhat}}
-
{{CRLtemplate|File:ID_hat.jpg|Hat|
+
{{CRLofficer_tunic_grey}}
-
* Fabric should be a medium weight suiting material exactly matching the tunic and pants. Gabardine style weave is most accurate. Color options are black or olive-greyish green.
+
-
* Base of the hat should be conical, with a crown about 4" (101.6 mm) tall.
+
-
* Front and rear "flaps" should overlap on the sides and be about 4" (101.6 mm) high.
+
-
* Front bill extends 3" down, decorated with 6 or 7 concentric stitches.
+
-
* Imperial Code Disk positioned in the center of the front vertical "flap."||}}
+
-
{{CRLtemplate|File:ID_disk.png|Imperial Code Disk|
+
{{CRLgeneric-rankbar}}
-
*A stepped cone shape appearing to be 3 disks stacked on top of one another.
+
-
*The bottom disk is 1" (25.3 mm) the middle disk is 3/4" (19.1 mm) and the top disk is 1/2" (12.7 mm.)
+
-
*There is an indentation in the center of the top disk about 1/4" (6.4 mm)||}}
+
-
{{CRLtemplate|File:ID_tunic.jpg|Tunic|
+
{{CRLcodecylindersOfficer}}
-
*Fabric should be a medium weight suiting material exactly matching the pants and hat. Gabardine style weave is most accurate. Color options are black or olive-greyish green.
+
-
*Tunic is double-breasted with a left over right closure on the tapered yoke.
+
-
*Yoke comes up across the shoulder to the top shoulder seam.
+
-
*The standing collar has square corners and is about 1.25" (31.8 mm) tall and closes snugly and includes a modesty panel behind closure. Collar edges are closed with two eye hooks. 
+
-
*There are code cylinder pockets on both outside panels of the jacket from about half way between the top and bottom on the arm hole.
+
-
*Sleeves are long, and without decoration, cuffs or buttons, containing 2 seams, one along the bottom and one along the back.
+
-
*Tunic should be constructed with no top-stitching (stitches visible on the exterior surface of fabric)|
+
-
*There is a dart of about 2" (50.8 mm) in the top center of the yoke.
+
-
*Additionally there is a seam running the entire circumference of the tunic, dividing it along a line hidden by the uniform belt.
+
-
*The back of the tunic has princess seams that run vertically and turn outward to intersect the arm-hole seam at the vertical center.|}}
+
-
{{CRLtemplate|File:ID_rankbar.jpg|Rank Bar|
+
{{CRLofficerbelt}}
-
*Worn on the left side of the tunic over the heart.
+
-
*Rank consists of colored plastic tiles mounted on metal bar.
+
-
*Each bar is 1" (25.4 mm) height, length is determined by chosen rank
+
-
*Rank tile dimensions are 1/2" (12.7 mm)width x 3/4" (19 mm) height and about 1/8" (3.2 mm).
+
-
*Tiles should be mounted with 1/4" (6.4 mm) spaces between them.|
+
-
*Rank tiles are translucent. Color quantity and combinations are determined by rank, and should be appropriate to uniform type (examples: no Grand Moffs wore black uniforms with hats, Grand Admiral rank should match Grand Admiral uniform, etc.).
+
-
*Double-row ranks should be constructed from separate pieces of one row each, rather than two rows of caps on a single metal backing piece.|}}
+
-
{{CRLtemplate|File:Blankwhite.gif|Code Cylinders|
+
{{CRLofficer_jodphurs_grey}}
-
*Between 1 to 4, tucked into small pockets in tunic by shoulders
+
-
*Two styles are available. Either may be used:
+
-
**Chalk-holder/dosimeter style: silver tube with short clip, top should be colored blue
+
-
**X-Wing pilot style: machined aluminum rod with flaring disc detail at top (Admiral Motti style)||}}
+
-
{{CRLtemplate|File:ID_gloves.jpg|Gloves (optional for grey uniforms)|
+
{{CRLofficer_boots}}
-
*Black, leather or leather-like, enclosed fingered, non-textured, gauntlet length and fitted.
+
-
*No buckles, straps, etc.||}}
+
-
{{CRLtemplate|File:ID_belt.jpg|Belt|
+
{{CRLaccessories}}
-
*The belt should be constructed from a non-textured leather or a leather-like material, approximately 2" (50.8 mm) in width (up to 3" (76.s mm) is acceptable)
+
-
*To the right of the buckle (from the viewer's perspective), a single large snap or rivet should be visible about 1" (25.4 mm) from the buckle.
+
-
*The buckle should be constructed from a horizontally brushed metal, or metal looking material.
+
-
*The size should be 2 5/8" (66.7 mm) high and 4 1/8" (104.5 mm) wide with 0.5" (12.7 mm) radius rounded corners.
+
-
*Canon buckles have a slight horizontal curve.
+
-
*Buckles are adorned with a Imperial Code Disk at the center.||}}
+
-
{{CRLtemplate|File:Blankwhite.gif|Belt Boxes (optional for grey uniforms)|
+
{{CRLtemplate|File:Officerbelt_boxes.jpeg|Belt Boxes|
-
* Dimensions are about 2 1/2" (63.5 mm) by 4 1/2" (114.3 mm) by 1" (25.4 mm) thick.
+
* Dimensions are approximately 2 1/2" (63.5 mm) by 4 1/2" (114.3 mm) by 1" (25.4 mm) thick.
-
* Boxes can be worn either vertically or horizontally on either side of the belt buckle.
+
* Two belt boxes may be worn, either vertically or horizontally, one each on either side of the belt buckle.|
-
* One or two boxes can be worn on either the right or left side of the belt, and symmetry is not required.|| }}
+
* ANH line officers shall have two belt boxes, worn either vertically or horizontally.
 +
* ESB and ROTJ line officers shall not have belt boxes.|
 +
* Belt box, code cylinder, and rank badge combination must be consistent with a film canon officer.
 +
* Belt boxes must be made of metal. }}
 +
{{CRLtemplate|File:ID_gloves.jpg|Gloves|
 +
*Black, leather or leather-like, enclosed fingered, non-textured, gauntlet length and fitted.
 +
*No buckles, straps, etc.|
 +
*ANH line officers shall not wear gloves.
 +
*ESB and ROTJ line officers shall wear gloves.|
 +
* Gloves must match the designs of each film appearance.}}
-
{{CRLtemplate|File:ID_pants.jpg|Pants|
+
{{CRLfooter|IOC_CRL|I}}
-
*Fabric should be a medium weight suiting material exactly matching the tunic and hat. Gabardine style weave is most accurate. Color options are black or olive-greyish green.
+
-
*Flared riding breeches are canon, with semi-stiff flares to the hip/thigh area for grey/green officer types. Breeches must be worn with boots (see below).
+
-
*''Straight-legged dress trousers are permitted for black-uniformed officers, but must be worn with quality dress shoes.''
+
-
*Pockets are acceptable, though they should not be visible with the tunic on.
+
-
*There are no noticeable cuffs on the pants.||}}
+
-
 
+
-
{{CRLtemplate|File:ID_boots.jpg|Boots|
+
-
*Knee-high, black, lace-less, non-textured, leather or leather-like material. Rubber is not acceptable.
+
-
*Both green and black uniforms wear high English dress riding style boots
+
-
* Black dress shoes may be worn instead of boots with a black officer uniform and straight legged dress trousers.||}}
+
-
 
+
-
 
+
-
{{CRLsubheading|Costume Accessories:}}
+
-
 
+
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Dress Shirt (for grey uniforms only)|
+
-
* A white standing collar dress shirt may be worn with the gray officer uniform if it is matched with a Grand Moff rank bar (consisting of 6 blue over 3 yellow and 3 red tiles) and 2 code cylinders in each of the 2 pockets (4 code cylinders total.)| | }}
+
-
 
+
-
{{CRLdh17}}
+
-
 
+
-
{{CRLgeneric-e11}}
+
-
 
+
-
{{CRLdh44}}
+

Revision as of 05:15, 31 January 2013

crlblackhd.gif
Imperial Line Officer (olive)
ID Line Officer Full.jpg
Model ID-5955, Photo by BJ Savage


Imperial-Officer-Corps.png

Description: Imperial Line Officer
Prefix: ID
Detachment: Imperial Officer Corps
Context: Star Wars Episodes IV - IV and Expanded Universe


The 501st approval requirements are listed in black.

The Imperial Officer Corp Detachment defines additional, optional levels of costuming excellence. In the page below, items listed in blue are optional features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.


This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
  • Any uncertainties or questionable aspects of the submitted costume should be brought to the appropriate DL/GML peer review section of the legion forum.
Required Costume Components

The following costume components are present and appear as described below.


ID Hat.jpg Hat, Olive
For 501st approval:
  • Fabric should be a medium weight suiting material exactly matching the tunic and pants. Gabardine style weave is most accurate.
  • Color must match the tunic and pants.
  • Base of the hat should be conical, with a crown about 4" (101.6 mm) tall.
  • Front and rear "flaps" should overlap on the sides and be about 4" (101.6 mm) high.
  • Front bill extends 3" down, decorated with 6 or 7 concentric stitches.
  • Imperial Code Disk positioned in the center of the front vertical "flap."
For level two certification (if applicable):
  • Code disk should have a notch in it on the outermost disk.
For level three certification (if applicable):
  • Code Disk should exactly match screen-used prop.


ID tunic.jpg Tunic, Olive
For 501st approval:
  • Fabric is a medium weight suiting material exactly matching the pants.
    • Gabardine style weave is most accurate.
  • Tunic is double-breasted with a left over right closure on the tapered yoke.
  • Yoke comes up across the shoulder to the top shoulder seam.
  • The standing collar has square corners and is about 1.25" (31.8 mm) tall.
    • Collar closes snugly and includes a modesty panel behind closure.
    • Collar edges are closed with two eye hooks.
  • There are code cylinder pockets on both outside panels of the jacket from about half way between the top and bottom on the arm hole.
  • Sleeves are long, and without decoration, cuffs or buttons.
  • Sleeves contain 2 seams.
    • One along the bottom and one along the back.
  • Tunic is constructed with no top-stitching (stitches visible on the exterior surface of fabric)
For level two certification (if applicable):
  • There is a dart of about 2" (50.8 mm) in the top center of the yoke.
  • There is a seam running the entire circumference of the tunic, dividing it along a line hidden by the uniform belt.
  • The back of the tunic has princess seams that run vertically and turn outward to intersect the arm-hole seam at the vertical center.
For level three certification (if applicable):
  • Tunic is secured on the right side by snaps or buttons.
    • Not hook and loop fastener (Velcro).
  • There is no top-stitching visible anywhere.
  • A lining is sewn in.


ID rankbar.jpg Rank Bar
For 501st approval:
  • See the Imperial Rank Bar page for more information.
  • Worn on the left side of the tunic over the heart.
  • Rank consists of colored plastic tiles mounted on metal bar.
  • Each bar is 1" (25.4 mm) height, length is determined by chosen rank
  • Rank tile dimensions are 1/2" (12.7 mm)width x 3/4" (19 mm) height and about 1/8" (3.2 mm).
  • Tiles are mounted with 1/4" (6.4 mm) spaces between them.
  • Rank tiles are translucent.
  • Color quantity and combinations are determined by rank, and are appropriate to uniform type.
    • Examples:
      • No Grand Moffs wear black uniforms with hats.
      • Grand Admiral rank matches Grand Admiral uniform (etc.)
For level two certification (if applicable):
  • Multiple tile rows are made from two separate metal strips, one atop the other and meeting together flush.
    • Double row rank bars are not allowed for staff (black uniformed) officers.
For level three certification (if applicable):
  • Belt box, code cylinder, and rank badge configuration is consistent with film canon officers.

Template:CRLcodecylindersOfficer


ID belt.jpg Belt
For 501st approval:
  • The belt is constructed from a non-textured leather or a leather-like material.
  • Approximately 2" (50.8 mm) in width, up to 3" (76.2 mm) is acceptable.
  • There are no loops on the belt.
  • A single large snap or rivet is visible approximately 1" (25.4 mm) from the buckle.
    • The belt may be worn with the snap to the right or left of the wearer.
  • The buckle is constructed from a horizontally brushed metal, or metal looking material.
  • The buckle size is approximately 2 5/8" (66.7 mm) high and 4 1/8" (104.5 mm) wide with 0.5" (12.7 mm) radius rounded corners.
  • Buckle is adorned with an Imperial Code Disk at the center.
    • Please refer to the Imperial Buckle reference page for information on accurate and inaccurate style buckles.
For level two certification (if applicable):
  • Belt is made of leather.
  • Snap is worn to the left of the wearer.
  • Buckle has a slight horizontal curve.


ID pants.jpg Jodphur Trousers, Olive
For 501st approval:
  • Fabric is a medium weight suiting material exactly matching the tunic. **Gabardine style weave is most accurate.
  • Flared riding breeches are canon, with semi-stiff flares to the hip/thigh area.
  • Breeches are worn with boots.
  • Pockets are acceptable, although are not visible with the tunic on.



ID Officer Boots.jpg Officer Boots
For 501st approval:
  • Knee-high, black, lace-less, smooth non-textured, leather or leather-like material.
    • Rubber is not acceptable.
    • PVC or synthetic material is allowed as long as it gives the appearance of leather.
  • There are no stretch panels, buckles, snap tabs, or decoration.
  • Boots have conservative heels.
  • If zippers are present, they are hidden on the inner part of the boot shaft.
    • Not visible from the front, side or back.
  • The top of the boots may be flat or Spanish Style, but not Cowboy or Super Hero (pointed at the front) style.
For level two certification (if applicable):
  • Boots do not have a zipper.
For level three certification (if applicable):
  • Boots are made of leather.
    • Not vinyl or PVC.
  • Exact replicas of English riding (dress) boots or Equestrian boots.
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.

Officerbelt boxes.jpeg Belt Boxes
For 501st approval:
  • Dimensions are approximately 2 1/2" (63.5 mm) by 4 1/2" (114.3 mm) by 1" (25.4 mm) thick.
  • Two belt boxes may be worn, either vertically or horizontally, one each on either side of the belt buckle.
For level two certification (if applicable):
  • ANH line officers shall have two belt boxes, worn either vertically or horizontally.
  • ESB and ROTJ line officers shall not have belt boxes.
For level three certification (if applicable):
  • Belt box, code cylinder, and rank badge combination must be consistent with a film canon officer.
  • Belt boxes must be made of metal.
ID gloves.jpg Gloves
For 501st approval:
  • Black, leather or leather-like, enclosed fingered, non-textured, gauntlet length and fitted.
  • No buckles, straps, etc.
For level two certification (if applicable):
  • ANH line officers shall not wear gloves.
  • ESB and ROTJ line officers shall wear gloves.
For level three certification (if applicable):
  • Gloves must match the designs of each film appearance.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:ID_imperial_officer

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.