(Difference between revisions)
(2 intermediate revisions not shown)
Line 1: Line 1:
-
{{CRLheader|Imperial Scanning Crew|File:IC_Scanning_Crew_Full.jpg|MODEL NAME|PHOTOGRAPHER NAME}}
+
{{CRLheader|Imperial Scanning Crew|File:IC_Scanning_Crew_Full.jpg|Aaron Garber|Cal Pierce}}
{{CRLdetinfo| 1108 |Imperial Scanning Crew|IC|Star Wars Episodes IV | }}
{{CRLdetinfo| 1108 |Imperial Scanning Crew|IC|Star Wars Episodes IV | }}
Line 33: Line 33:
* [[Costuming:Imperialdisk|Imperial Code Disk]] positioned in the center of the front vertical "flap."|
* [[Costuming:Imperialdisk|Imperial Code Disk]] positioned in the center of the front vertical "flap."|
* Code disk should have a notch in it on the outermost disk.
* Code disk should have a notch in it on the outermost disk.
-
* ESB scanning crew shall have a green hat, not black.|}}
+
* ESB scanning crew shall have a green hat, not black.|
 +
* Code disk should exactly match a screen used prop.}}
Line 48: Line 49:
{{CRLtemplate|File:IC_Scanning_Compad.jpg|Imperial Communications Pad|
{{CRLtemplate|File:IC_Scanning_Compad.jpg|Imperial Communications Pad|
-
* Alternate style communications pad with buttons and detailing as shown.
+
* If worn, the compad must be the alternate style with buttons and detailing as shown.
* Compads shall not be electronically lit. |
* Compads shall not be electronically lit. |
*ANH scanning crew shall have a compad.
*ANH scanning crew shall have a compad.
Line 64: Line 65:
*ANH scanning crew shall have two vertical belt boxes.
*ANH scanning crew shall have two vertical belt boxes.
*ESB scanning crew shall have no belt boxes.
*ESB scanning crew shall have no belt boxes.
-
*ROTJ scanning crew may have a single vertical betl box to the wearer's left side of the belt buckle.| }}
+
*ROTJ scanning crew may have a single vertical belt box to the wearer's left side of the belt buckle.|  
 +
* Belt boxes must be metal.}}
{{CRLfooter|IOC_CRL|I}}
{{CRLfooter|IOC_CRL|I}}

Revision as of 05:33, 1 March 2013

crlblackhd.gif
Imperial Scanning Crew
500px
Model Aaron Garber, Photo by Cal Pierce


Imperial-Officer-Corps.png

Description: Imperial Scanning Crew
Prefix: IC
Detachment: Imperial Officer Corps
Context: Star Wars Episodes IV


The 501st approval requirements are listed in black.

The Imperial Officer Corp Detachment defines additional, optional levels of costuming excellence. In the page below, items listed in blue are optional features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.


  • This CRL is a work in progress.
  • This costume may be approved by GMLs, but until the library entry is complete, it is suggested that this character first be submitted to the appropriate DL/GML peer review section of the legion forum.
  • If you have this costume and would like to assist with the completion of this library entry, please contact your detachment leader.
  • Please note that the use of the word "should" below does not indicate that the armor piece is considered open to interpretation. All instances of "should be" and "should have" will be replaced with "is" and "has", as this guide is completed.
Required Costume Components

The following costume components are present and appear as described below.


ID hat black.jpg Imperial Hat, black
For 501st approval:
  • Fabric is a medium weight suiting material matching the pants and tunic if applicable.
    • Gabardine style weave is most accurate.
  • Base of the hat is conical, with a crown about 4" (101.6 mm) tall.
  • Front and rear "flaps" overlap on the sides and are about 4" (101.6 mm) high.
  • Front bill extends 3" down, decorated with 6 or 7 concentric stitches.
  • Imperial Code Disk is positioned in the center of the front vertical "flap."
For level two certification (if applicable):
  • Code Disk has a notch detail on the outermost disk.
For level three certification (if applicable):
  • Code disk exactly matches screen-used prop.


Imperial flightsuit grey.jpg Grey Imperial Flight Suit
For 501st approval:
  • One piece light grey coverall/jumpsuit/flight suit with a front invisible zipper.
  • Approximately 1.5" (38.1mm) tall mandarin collar with a chevron shaped, left-over-right velcro closure.
  • A silver or white "imperial cog" emblem on a black background must be present on both shoulders. The cog is 3" or 3.5" in diameter, and 1" from the shoulder seam.
    • If the costume includes armor that covers the cog emblems entirely, they may be omitted.
  • On the left forearm there is a com-pad pocket approximately 5" (127mm) wide by 5.75" (146.05mm) tall with no flap and a 2.25" (57.15mm) window in it. (Size might vary to match your com-pad)
  • On the left bicep, approximately 2" (50.8mm) below the cog emblem, there is a code cylinder pocket with no flap, and vertical stitching dividing it into pen sleeves.
  • The bottom front corner of the pocket is cut off at a bevel on the side pointing in view direction with the broader upside forming the border of the pen sleeves.
  • The right sleeve has a cargo pocket approximateyl 6" (152mm) wide and 5.75" (146mm) on the bicep approx 2"(50.8mm) below the cog emblem. The pocket has a 2"(50.8mm) flap.
  • 2 large chest pockets and 2 large front pockets below the belt without any zipper or flaps
  • 2 leg pockets with flaps similar in proportion as the one on the right arm sleeve. Size may differ. (Usually the width of the front pockets equals the width of the leg pockets)
  • Rank bars of any kind are not permitted.
  • There are no leg pockets below the knees
For level two certification (if applicable):
  • All pocket flaps to have chevron point.
For level three certification (if applicable):
  • Imperial patches on the shoulders shall be printed vinyl rather than embroidered.
  • The suit has a pointed collar in the back.


ID belt.jpg Belt
For 501st approval:
  • The belt is constructed from a non-textured leather or a leather-like material.
  • Approximately 2" (50.8 mm) in width, up to 3" (76.2 mm) is acceptable.
  • There are no loops on the belt.
  • A single large snap or rivet is visible approximately 1" (25.4 mm) from the buckle.
    • The belt may be worn with the snap to the right or left of the wearer.
  • The buckle is constructed from a horizontally brushed metal, or metal looking material.
  • The buckle size is approximately 2 5/8" (66.7 mm) high and 4 1/8" (104.5 mm) wide with 0.5" (12.7 mm) radius rounded corners.
  • Buckle is adorned with an Imperial Code Disk at the center.
    • Please refer to the Imperial Buckle reference page for information on accurate and inaccurate style buckles.
For level two certification (if applicable):
  • Belt is made of leather.
  • Snap is worn to the left of the wearer.
  • Buckle has a slight horizontal curve.


Generic-black-boots.jpeg Black Boots
For 501st approval:
  • Calf high black leather or leather like material.
  • Free of laces, decorative stitching, buckles on the instep or any other embellishments.
  • Boots may have a single adjustment strap at the top outside of the boot, with the buckle no wider than 1".
    • This need not be functional.
  • Zippers on the inside of the boot are acceptable, so long as they are concealed.
    • If the zipper is not covered by vinyl/leather, it is painted black.
  • German "jack boot" style boots are most canon.
For level two certification (if applicable):
  • Boots are made of leather.
For level three certification (if applicable):
  • Boots are German jack boots (or “Knobelbechers”) or an authentic replication thereof.
  • Boots have the top adjustment strap.
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.

Blankwhite.gif Summary of L2 requirements
For 501st approval:
  • ANH: No gloves. Has 2 code cylinders, 2 vertical belt boxes, and the alternate style compad.
  • ESB: Green hat instead of black, and 3 code cylinders. No belt boxes, gloves, or compad. May have a headset.
  • ROTJ: has guantlets and may have a single vertical belt box. No code cylinders, compad, or headset.


ID Hat.jpg Hat
For 501st approval:
  • Fabric should be a medium weight suiting material exactly matching the tunic and pants. Gabardine style weave is most accurate.
    • Color options for officer are black or olive-greyish green and must match the tunic and pants.
    • Color option for imperial crew is black.
  • Base of the hat should be conical, with a crown about 4" (101.6 mm) tall.
  • Front and rear "flaps" should overlap on the sides and be about 4" (101.6 mm) high.
  • Front bill extends 3" down, decorated with 6 or 7 concentric stitches.
  • Imperial Code Disk positioned in the center of the front vertical "flap."
For level two certification (if applicable):
  • Code disk should have a notch in it on the outermost disk.
  • ESB scanning crew shall have a green hat, not black.
For level three certification (if applicable):
  • Code disk should exactly match a screen used prop.


IC headset.jpg Crew Headset
For 501st approval:
  • Silver and black headset with microphone.
For level two certification (if applicable):
  • ANH and ROTJ scaning crew shall not wear headsets.
For level three certification (if applicable):
150px Code Cylinders
For 501st approval:
  • Crewman style: machined aluminum rod with flaring disc detail at top
  • Two or three may be worn.
For level two certification (if applicable):
  • ANH scanning crew shall have 2 code cylinders.
  • ESB scanning crew shall have 3 code cylinders.
  • ROTJ scanning crew shall not have code cylinders.
For level three certification (if applicable):
IC Scanning Compad.jpg Imperial Communications Pad
For 501st approval:
  • If worn, the compad must be the alternate style with buttons and detailing as shown.
  • Compads shall not be electronically lit.
For level two certification (if applicable):
  • ANH scanning crew shall have a compad.
  • ESB and ROTJ bridge crew shall not have a compad.
For level three certification (if applicable):
Black-gauntlet-gloves.jpeg Black Gauntlet Gloves
For 501st approval:
  • Black, leather or leather-like, enclosed fingered, non-textured, fitted gauntlet style.
  • No buckles, straps, or decorative stitching are permitted.
For level two certification (if applicable):
  • Gloves shall be made of leather.
  • ANH and ESB scanning crew shall not wear gloves.
  • ROTJ scanning crew shall wear gauntlet style gloves.
For level three certification (if applicable):
Officerbelt boxes.jpeg Belt Boxes
For 501st approval:
  • Dimensions are approximately 2 1/2" (63.5 mm) by 4 1/2" (114.3 mm) by 1" (25.4 mm) thick.
For level two certification (if applicable):
  • ANH scanning crew shall have two vertical belt boxes.
  • ESB scanning crew shall have no belt boxes.
  • ROTJ scanning crew may have a single vertical belt box to the wearer's left side of the belt buckle.
For level three certification (if applicable):
  • Belt boxes must be metal.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:IC_imperial_scanning_crew

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.