Description: A'Sharad Hett
Prefix: DZ
Detachment: Flagship Eclipse Detachment
Context: Star Wars Expanded Universe
After surviving Order 66 during the Clone Wars, A'Sharad Hett traveled back to Tatooine and returned to his Tusken heritage. Hett became the war leader of several clans and made the Tusken raiders a force to be feared. After his defeat at the hands of Obi-Wan Kenobi, Hett left Tatooine to become a bounty hunter until his Sith destiny unfolded. A'Sharad Hett ultimately becomes Darth Krayt.

• This CRL is a work in progress.
• While this costume must be approved by the Legion Membership Officer, submissions should still go to the local GML, who will post the application in the appropriate section of the Legion forum.
• If you have this costume and would like to assist with this CRL, please contact your detachment leader!
• Please note that the use of the word "should" below does not indicate that a requirement is optional. All instances of should will be replaced with must as this guide is completed.

• The head is wrapped in weathered, sand-colored cloth. Duck cloth or bull denim is preferred.
• The wraps are snug against the head and the ends do not hang loosely.
• Dark brown leather or simulated leather is used for the face wrapping.
• The metallic eye stalks are tapered toward the front with two slots cut into the underside of each piece.
• Lenses tinted dark red are used to hide the costumer's eyes.
• There are four tapered metallic head spikes.
• There are two metallic blood spitters (cheek tusks).
• The metallic nose piece has two vertical slots.
• Black screening is used so the mouth is not visible from the outside of mask.
  

• A waist length, dark brown braid emerges from the back of helmet.
• Cloth wraps are used to keep the braid from unraveling.
  

• The wrapped fabric neck seal is extended to create an attached dickey, which is worn under the inner tunic and covers the costumer's chest.
• The neck seal and dickey are made of weathered, sand-colored fabric.
  

• The breather is a small, weathered cylinder approximately 10 cm wide.
• If desired, the cylinder can be wrapped with dark brown leather or a leather-like material.
• Tapered gaskets on either end of the cylinder are connected to a tube, which is bent to a 90 degree angle on each side before wrapping around the neck.
  

• A light khaki, Jedi style tunic is worn under the tabard.
• The sleeves of the tunic are tucked into the arm wraps.
  

• A dark brown outer tunic is made from the same material as the pants. This tunic reaches to the middle of the costumer's thighs in the front and back, and the fabric is weathered.
• From the back, the outer tunic appears to be a coat with a standing collar.
• From the front, the outer tunic appears to be a pair of Jedi style tabards which are attached to the standing collar.
• The sides of the outer tunic are left open.
  

• Dark brown leather gloves are worn.
• Cloth wrappings start at the wrist inside the gloves and continue up the elbow, covering the sleeves of the tunic.
• The sand colored wraps are weathered and conceal all skin on the arms.
  

• The Jedi style waist sash or obi is made from the same heavily weathered material as the inner tunic.
  

• A dark brown Jedi style belt is worn over the sash.
• The belt has four sets of button studs which hold the narrow secondary belt in place over the wide main belt. A decorative buckle is located on the narrow belt in the front.
• The main belt closes in the back, and a piece of dark brown leather wraps around the closure point.
• Four brown leather pouches are worn at the back of the belt, two on the left and two on the right.
• Three Jedi food capsules are worn on the belt.
  

• The pants are made from a dark brown material.
• The pant legs are tucked into the boots.
  

• The knee high boots are covered with weathered, sand-colored cloth wrappings.
  

Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.

• A'Sharad Hett carries two lightsabers: his own and his father's.
• A'Sharad Hett's lightsaber is wrapped in leather and includes two long straps bearing beads and six krayt dragon claws.
• The second light saber is based on Sharad Hett's lightsaber design.
• If blades are used, they must be green in color.