crlblackhd.gif
Jesse (Phase 2)
Missingprofile.jpg
Model none, Photo by none


Clone-Trooper-Detachment.png

Description: Clone Trooper Jesse (Phase 2)
Prefix: CT
Detachment: Clone Trooper Detachment
Context: Star Wars: The Clone Wars, Season 4

Jesse is respected as a well-mannered and loyal Republic trooper.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: Effective June 1 2012, the 501st will no longer be approving realistic interpretations of Clone Wars CG characters. The armor sculpt must match the character being recreated. See this thread at clonetroopers.net for the differences between the sculpts.

  • This CRL is a work in progress.
  • While this costume must be approved by the Legion Membership Officer, submissions should still go to the local GML, who will post the application in the appropriate section of the Legion forum.
  • If you have this costume and would like to assist with this CRL, please contact your detachment leader!
  • Please note that the use of the word "should" below does not indicate that a requirement is optional. All instances of should will be replaced with must as this guide is completed.

Required Costume Components

The following costume components must be present and appear as described below for approval .

Blankwhite.gif Helmet
For 501st approval:
  • Helmet painted matte white.
  • A large Galactic Republic symbol covers nearly the entire front and top of the helmet dome.
  • The helmet eye lens and nose area are outlined in blue with the lines converging to a point over the lower chin area.
  • The blue line across the top of the lens extends around to the back of the helmet and converges with the larger blue section on the rear quarter.
  • The rectangle ear caps are painted grey.
  • Side vent tubes have 6 hash marks on each.
  • The rear of the helmet has an indented band that is filled with a slightly darker shade of blue than what is on the front of the helmet.
  • Each rear quarter of the helmet, from the backside of the earpieces to the center rear section, is painted blue. This includes all four walls of the indented section. This color extends from the upper indented helmet band down to the curved lower collar.
  • The center round cap, on the rear of the helmet, is painted grey.
  • If weathered, the blue areas include heavy scuff marks and fading.
  • Weathering of white areas are shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Neck Seal
For 501st approval:
  • Neck seal is black in color with vertical ribbing.

The neckseal stands tall, "turtleneck" style and reaches nearly to the chin.

  • No logos or labels are to be visible.

For level two certification (if applicable):
For level three certification (if applicable):


TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


Blankwhite.gif Shoulder Bells
For 501st approval:
  • Armor painted with a base of matte or satin white.
  • Each shoulder has a wide blue stripe down the center.
  • If weathered, the blue areas include heavy scuff marks and fading.
  • Weathering of white areas are shades of grey.
For level two certification (if applicable):
  • Shoulder bells must be weathered.
For level three certification (if applicable):
Blankwhite.gif Upper Arm Armor
For 501st approval:
  • Armor painted with a base of matte or satin white.
  • Each bicep has a blue stripe down the center which is aligned with the shoulder armor.
  • If weathered, the blue areas include heavy scuff marks and fading.
  • Weathering of white areas are shades of grey.
  • Biceps should be seamless.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):
Blankwhite.gif Forearm Armor
For 501st approval:
  • Armor painted with a base of matte or satin white.
  • Front of both forearms have a blue stripe.
  • Right forearm must have a compad that has 6 raised buttons, with a larger rectangle above them. A smaller raised section is closest to the elbow.
  • Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
  • Elbow plate is integrated into the forearm armor.
  • Elbow section has blue stripe.
    • Stripes on front of forearm and elbow pieces do not align.
  • Weathering of blue areas include heavy scuff marks and fading.
  • Weathering of white areas are shades of grey.
For level two certification (if applicable):
  • Armor must be seamless. No visible traces of how the armor was assembled should be shown.
  • Armor must be weathered.
For level three certification (if applicable):
Blankwhite.gif Hand Plates
For 501st approval:
  • Painted with a base color of matte or satin white.
  • If weathered, the weathering should be shades of grey.
  • Hand plates are mirror images of each other.
  • Hand plates have an angled peak that comes to a point over the index or middle finger, just past the main knuckle of the hand.
For level two certification (if applicable):
For level three certification (if applicable):


Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Chest Armor
For 501st approval:
  • Armor painted with a base of matte or satin white.
  • Center of chest has a vertical blue stripe which starts below the top edge of the armor and ends short of the bottom edge.
  • Weathering of blue areas include heavy scuff marks and fading.
  • Weathering of white areas are shades of grey.
  • Shoulder straps are white.
  • Lower portion of the chest is shaped to match the abdomen armor.
  • Chest and back plate should match together at the sides with no open gap.
    • There is a butted seam line present between the front and back pieces.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):
Blankwhite.gif Back Armor
For 501st approval:
  • Armor painted with a base of matte or satin white.
  • Back armor has a detail plate consisting of 4 circles and 5 horizontal bars.
  • Weathering of white areas are shades of grey.
  • Chest and back plate should match together at the sides with no open gap.
    • There is a butted seam line present between the front and back pieces.
  • Shoulder straps are white.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):
Blankwhite.gif Ab Armor
For 501st approval:
  • Armor painted with a base of matte or satin white.
  • Near the top of the ab piece is a short rectangular dash which tapers inward slightly as it travels downward.
    • When the chest and ab armor are combined, the two dash marks resemble an exclamation point.
  • Weathering of blue areas include heavy scuff marks and fading.
  • Weathering of white areas are shades of grey.
  • Top top section of the armor piece is shaped off to match the chest armor.
  • The ab armor protrudes out in the middle to match the shape of the chest.
  • The ab armor joins at the rear and the join is covered by a center plate.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):
Blankwhite.gif Codpiece and belt front
For 501st approval:
  • Armor painted with a base of matte or satin white.
  • If weathered, the weathering should be shades of grey.
  • Belt is approx 3" tall and divided into segments. The front segments have a key/slot detail.
  • Belt boxes are mounted on each side.
  • Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):
Blankwhite.gif Posterior Armor, belt rear and detonator
For 501st approval:
  • Armor painted with a base of matte or satin white.
  • If weathered, the weathering should be shades of grey.
  • Belt is approx 3" tall and divided into segments.
  • Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.
  • Detonator is centered on the back of belt with no control buttons.
    • The detonator has 2 lines set in approx 1/2" - 5/8" from the edges.
    • Lines may be recessed or painted on.
    • Center of each round detonator end cap is painted grey.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):
Blankwhite.gif Thigh Armor
For 501st approval:
  • Armor painted with a base of matte or satin white.
  • Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor.
  • From the top of the triangle a ridge line should travel up the front of the thigh to the top.
  • The upper outer edge should have an angled section.
  • The rear of the thigh should have an indentation.
  • Armor must be seamless. No visible traces of how the armor was assembled should be shown.
  • Weathering is shades of grey.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):
Blankwhite.gif Shin Armor
For 501st approval:
  • Armor painted with a base of matte or satin white.
  • Knee armor is integrated with the lower leg.
  • The knees are painted dark grey with a narrow horizontal white band across the center. This white band rises as it crosses the face of the knee and drops back lower as the travels around the sides.
  • The front of each shin is painted blue.
  • The blue color starts just below the knee section leaving a white band between the blue color and the knee piece. This blue color ends short of the lower edge, leaving a white band around the bottom of the armor piece.
  • The rear of the shin should have an indentation.
  • Outer seam of the shin must be seamless.
  • A clam shell opening on the inner seam is acceptable.
  • Weathering of white areas are shades of grey.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):


TC animated boots.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
  • Boots have a center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap.
For level two certification (if applicable):
  • Boots must have accurate notched sole.
For level three certification (if applicable):
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.


CRLdc15s-animated.jpg DC-15S Blaster Carbine (animated style)
For 501st approval:

This is the animated variant of the DC-15S blaster rifle. Manufactured by BlasTech Industries, this weapon is commonly carried by the Troopers of the Galactic Republic.


This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:CT_-_Jesse_phase_2

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.