(Difference between revisions)
(18 intermediate revisions not shown)
Line 1: Line 1:
-
{{CRLheader|501st Clone Trooper|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}
+
{{CRLheader|501st Clone Trooper|File:501st_model.jpg|CT4841|Sharon Langthorne}}
{{CRLdetinfo| 1111 |501st Clone Trooper|CT|Episode III: Revenge of the Sith|
{{CRLdetinfo| 1111 |501st Clone Trooper|CT|Episode III: Revenge of the Sith|
The 501st Legion, later known as "Vader's Fist," was an elite unit of clone troopers commissioned by Supreme Chancellor Palpatine  during the Clone Wars that later became a stormtrooper unit.  The 501st fought in many battles, such as the Battle of Teth and the Battle of Coruscant, becoming one of the most well-known legions.  It was the 501st that was led into the Jedi temple by Darth Vader and helped destroy the Jedi there. In 19 BBY, the 501st became Darth Vader's personal unit as he led them during Operation: Knightfall, in which the clones  helped take down the Jedi, whom they believed to be traitors to the Republic.  }}
The 501st Legion, later known as "Vader's Fist," was an elite unit of clone troopers commissioned by Supreme Chancellor Palpatine  during the Clone Wars that later became a stormtrooper unit.  The 501st fought in many battles, such as the Battle of Teth and the Battle of Coruscant, becoming one of the most well-known legions.  It was the 501st that was led into the Jedi temple by Darth Vader and helped destroy the Jedi there. In 19 BBY, the 501st became Darth Vader's personal unit as he led them during Operation: Knightfall, in which the clones  helped take down the Jedi, whom they believed to be traitors to the Republic.  }}
-
{{CRLwipgmlapproval}}
+
{{CRLctnlevels}}
-
 
+
 +
 +
{{CRLgmlapproval}}
 +
 +
{{CRLrequirements}}
{{CRLrequirements}}
 +
 +
 +
{{CRLtemplate|File:501-Appo helmet copy.jpg|Helmet|
 +
 +
*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
 +
*Visor - Black Visor.
 +
*Helmet mohawk on dome.
 +
*Starting on the nose of the helmet, there is a blue stripe about 1 inch wide going from the vents to the vocoder. From the middle of the two centermost vents to half an inch off the center eye curves, the area in between should be painted pale blue. Continuing from there, widening out to 3 inches from center of the mowhawk, the pale blue stripe continues. It then thins to 4 inches in the rear of the helmet squared off in the back, ¼ inch above the grey helmet wrap.
 +
*Vertical stripes on each side of helmet cheeks that are dark blue in color.
 +
*Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
 +
*Primer grey stripe around back of dome.
 +
*Ear caps are painted a dark grey.
 +
*Helmet has the appearance of a neck ring.
 +
*Helmet may have an optional enclosed complete neck ring that seals the helmet to the neck.|
 +
*No additional requirements.|
 +
*Helmet must have a full neck ring.}}
-
{{CRL-CT-501st-helmet}}
+
-
 
+
{{CRL-realistic-clone-neckseal}}
-
{{CRL-generic-clone-neckseal}}
+
{{CRL-generic-undersuit}}
{{CRL-generic-undersuit}}
-
{{CRL-CT-501st-shoulders}}
+
{{CRLtemplate|File:501st clone shoulder bells2.jpg |Shoulder Bells|
 +
*Armor should be painted blue.
 +
*Shoulders should be tear drop in shape with all rounded edges. | |
 +
*Shoulder bells should not be symmetrical.  The Shoulder bells should slightly curve back at the bottom of the shoulder. }}
-
{{CRL-generic-clone-bicep}}
+
{{CRLtemplate|File:Clone bicept copy.jpg|Upper Arm Armor|
-
 
+
*Armor should be painted matte or satin white.
-
{{CRLtemplate|File:Blankwhite.gif|Elbow Armor|  
+
*Should have a dimple on the lower area of the back of the arm.  The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.||
 +
*Armor should be seamless.  No visible traces of how the armor was assembled should be shown.}}
 +
 +
{{CRLtemplate|‎File:Clone elbow copy.jpg|Elbow Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
-
**At the wrist of the forearms, a wrist stripe that is approximately 1 inch wide should circle the lower cuff. It should be painted pale blue.
 
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
* Both elbows have strapping.  The straps should have a raised detail line at the top and bottom of the strap.| |
* Both elbows have strapping.  The straps should have a raised detail line at the top and bottom of the strap.| |
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
+
{{CRLtemplate| |Forearm Armor|
 +
*Armor should be painted matte or satin white.
 +
*Both left and right forearms should be mirror images of each other.
 +
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
 +
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
 +
*The wrist of the forearm must have a blue stripe that wraps around the entire circumference of the forearm | |
 +
*Compad has detail antenna on its left.
 +
*Instead of a hard edge the top of the forearm has a bone ridge.
 +
*Armor should be seamless.  No visible traces of how the armor was assembled should be shown.}}
 +
 +
{{CRLtemplate|File:Clone hand guards copy.jpg|Hand Plates|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
-
*Both left and right forearms should be mirror images of each other.
+
*Hand plates are mirror images of each other.  
-
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectanular button.
+
-
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
+
-
*Armor should be seamless.  No visible traces of how the armor was assembled should be shown. | |
+
-
*Compad has detail antenna on its left.
+
-
*Instead of a hard edge the top of the forearm has a bone ridge.}}
+
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
+
-
*Armor should be painted matte or satin white
+
-
*Hand plates are mirror images of each other.
+
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Gloves|
+
{{CRL-generic_black_gloves}}
-
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}
+
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
+
{{CRLtemplate|File:501st clone chest plate2.jpg|Chest Armor|
-
*Armor should be painted matte or satin white.
+
*Armor should be painted matte or satin white.
-
**The chest has a command stripe that starts 3 inches wide centered in the middle of the chest and widens out to the width of the return curve. From this point the command stripe follows the rib line 1,.5 inch above the return curve to approximately the center of the front two belt boxes. At this point the square off and are do not continue. In the center of the command stripe, a 1 inch thick i mark is made. The dot of the i should be 1.5 inch wide and ½ to ¾ tall and centered just underneath the pectorial meeting vector. The body of the i is just a vertical line that finishes in the rib return curve
+
*Two detail slots on right breast.
*Two detail slots on right breast.
-
*Chest and back plate should match together at the sides with no gap, just a seam line.  
+
*Chest armor must have a blue stripe that begins at the center of the neck and extends down the chest plate to the bottom of the breast plate. From there it extends out towards the sides. Consult reference images for more detail.
-
*Shoulder straps should be placed underneath the chest to connect to the back. |  
+
*Chest and back plate should match together at the sides with no gap, just a seam line.
-
|
+
*Shoulder straps should be placed underneath the chest to connect to the back. ||
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Back Armor|
+
{{CRLtemplate|File:501st clone back plate 2.jpg|Back Armor|
-
*Armor should be painted matte or satin white.
+
*Armor should be painted matte or satin white.
-
**The detail plate should be painted pale blue.
+
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
-
*Chest and back plate should match together at the sides with no gap, just a seam line.  
+
*Rear tank detailed area is painted blue.
-
*Shoulder straps should be placed underneath the chest to connect to the back. |  
+
*Chest and back plate should match together at the sides with no gap, just a seam line.
-
|
+
*Shoulder straps should be placed underneath the chest to connect to the back. ||
-
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
+
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
*Highly detailed resin insert should replace softer details. }}
*Highly detailed resin insert should replace softer details. }}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
+
{{CRLtemplate|File:Clone abb2.jpg|Ab Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
-
*Ab section should be completely contained under the chest and back armor. |
+
*Ab section should be completely contained under the chest and back armor. ||
-
|
+
* Ab section should be seamless at the sides and close in the back.  A detail plate should cover the seam line and hide all work.}}
* Ab section should be seamless at the sides and close in the back.  A detail plate should cover the seam line and hide all work.}}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Cod and Posterior Armor|
+
 +
{{CRLtemplate|File:CLone cod and rear.jpg|Cod and Posterior Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
*Cod and Posterior armor should connect at the hips. | |
*Cod and Posterior armor should connect at the hips. | |
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Belt|
+
 +
{{CRLtemplate|File:Clone Belt copy.jpg|Belt|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Ammo Belt with boxes and detonator.
-
*Detonator is centered on the back of belt.  
+
*Detonator is centered on the back of belt.
-
*8 boxes total, 4 on each side of abdomen and attached to the belt. |
+
*8 boxes total, 4 on each side of abdomen and attached to the belt. ||
-
|
+
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Belt Boxes should be notched and fitted flush with the details of the belt.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Thigh Armor|
+
-
*Armor should be painted matte or satin white.
+
{{CRLtemplate|File:501st clone thigh armor 2.jpg|Thigh Armor|
-
**There should be two pale blue vertical stripes running center of the outer thighs that are approximately 3/4 inch wide and approximately 1 inch apart.
+
*Armor should be painted matte or satin white.
-
* Front of thigh armor should have a flat triangular area near the knee.  From the top of the triangle a ridge line should go up the front of the thigh to the top.
+
* Front of thigh armor should have a flat triangular area near the knee.  From the top of the triangle a ridge line should go up the front of the thigh to the top.
*Rear of the thigh should have an indention.
*Rear of the thigh should have an indention.
-
*Armor should be seamless.  No visible traces of how the armor was assembled should be shown. |  
+
*Down the outside of each thigh, there are 2 blue stripes spaced about an inch apart. These stripes line up with the stripes on the calves. ||
-
|
+
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.
-
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded. }}
+
*Armor should be seamless.  No visible traces of how the armor was assembled should be shown. }}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Knee Armor|
+
{{CRLtemplate||Knee Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
-
**The lower part of the knees should have a V like pale blue stripe.
 
*Knees should wrap around the front of the leg.  From top center a raised detail line should be present.
*Knees should wrap around the front of the leg.  From top center a raised detail line should be present.
-
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
+
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
-
|
+
*There is a blue stripe that follows the bottom curve of the knee plate.|
*Center strap should be primer gray.
*Center strap should be primer gray.
-
*Connection between the knee and the strapping should have a detail clip.}}
+
*Connection between the knee and the strapping should have a detail clip.|}}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
+
{{CRLtemplate|File:501st clone shin armor2.jpg|Lower Leg Armor|
*Armor should be painted matte or satin white.
*Armor should be painted matte or satin white.
-
**There should be two pale blue vertical stripes running center of the outer calves that are approximately 3/4 inch wide and aproximately 1 inch apart.
 
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
-
*Calf can have an access area on the inside of the leg.  The outside of the calf should be closed. |
+
*Calf can have an access area on the inside of the leg.  The outside of the calf should be closed.
-
|
+
*Down the outside of each calf , there are 2 blue stripes spaced about an inch apart. These stripes line up with the stripes on the thighs. ||
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Boots|
+
{{CRLtemplate|File:Clone shoes copy.jpg|Boots|
-
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles. The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap. There should be no markings or labels from the shoe makers. Boot soles should be primer gray. | | }}
+
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.  
 +
* Boots must be lace-less and have flat soles.  
 +
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.  
 +
* This strap should be white.
 +
*There should be no markings or labels from the shoe makers. The shoe soles should be gray. | | }}
 +
{{CRLaccessories}}
{{CRLaccessories}}
-
 
+
{{CRLdc15s-realistic}}
{{CRLdc15s-realistic}}
 +
 +
{{CRLdc15a-realistic}}
-
{{CRLdc15a-realistic}}
+
{{CRLfooter|CTN_CRL|C}}

Revision as of 01:20, 13 March 2013

crlblackhd.gif
501st Clone Trooper
501st model.jpg
Model CT4841, Photo by Sharon Langthorne


Clone-Trooper-Detachment.png

Description: 501st Clone Trooper
Prefix: CT
Detachment: Clone Trooper Detachment
Context: Episode III: Revenge of the Sith
The 501st Legion, later known as "Vader's Fist," was an elite unit of clone troopers commissioned by Supreme Chancellor Palpatine during the Clone Wars that later became a stormtrooper unit. The 501st fought in many battles, such as the Battle of Teth and the Battle of Coruscant, becoming one of the most well-known legions. It was the 501st that was led into the Jedi temple by Darth Vader and helped destroy the Jedi there. In 19 BBY, the 501st became Darth Vader's personal unit as he led them during Operation: Knightfall, in which the clones helped take down the Jedi, whom they believed to be traitors to the Republic.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.


This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
  • Any uncertainties or questionable aspects of the submitted costume should be brought to the appropriate DL/GML peer review section of the legion forum.


Required Costume Components

The following costume components are present and appear as described below.


150px Helmet
For 501st approval:
  • Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
  • Visor - Black Visor.
  • Helmet mohawk on dome.
  • Starting on the nose of the helmet, there is a blue stripe about 1 inch wide going from the vents to the vocoder. From the middle of the two centermost vents to half an inch off the center eye curves, the area in between should be painted pale blue. Continuing from there, widening out to 3 inches from center of the mowhawk, the pale blue stripe continues. It then thins to 4 inches in the rear of the helmet squared off in the back, ¼ inch above the grey helmet wrap.
  • Vertical stripes on each side of helmet cheeks that are dark blue in color.
  • Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
  • Primer grey stripe around back of dome.
  • Ear caps are painted a dark grey.
  • Helmet has the appearance of a neck ring.
  • Helmet may have an optional enclosed complete neck ring that seals the helmet to the neck.
For level two certification (if applicable):
  • No additional requirements.
For level three certification (if applicable):
  • Helmet must have a full neck ring.


Clone trooper neck seal.jpg Neck Seal
For 501st approval:
  • Neck seal is black in color with vertical ribbing or being smooth in appearance.
  • No logos or labels are visible.
    • If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.



TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


150px Shoulder Bells
For 501st approval:
  • Armor should be painted blue.
  • Shoulders should be tear drop in shape with all rounded edges.
For level two certification (if applicable):
For level three certification (if applicable):
  • Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder.
150px Upper Arm Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.
For level two certification (if applicable):
For level three certification (if applicable):
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
Clone elbow copy.jpg Elbow Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
  • Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.
For level two certification (if applicable):
For level three certification (if applicable):
  • Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.
[[ |150px]] Forearm Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Both left and right forearms should be mirror images of each other.
  • Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
  • Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
  • The wrist of the forearm must have a blue stripe that wraps around the entire circumference of the forearm
For level two certification (if applicable):
For level three certification (if applicable):
  • Compad has detail antenna on its left.
  • Instead of a hard edge the top of the forearm has a bone ridge.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
150px Hand Plates
For 501st approval:
  • Armor should be painted matte or satin white.
  • Hand plates are mirror images of each other.
  • Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.
For level two certification (if applicable):
For level three certification (if applicable):


Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
  • Gloves cover any exposed skin.
  • Gloves do not show any labels or logos when the armor is worn.



501st clone chest plate2.jpg Chest Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Two detail slots on right breast.
  • Chest armor must have a blue stripe that begins at the center of the neck and extends down the chest plate to the bottom of the breast plate. From there it extends out towards the sides. Consult reference images for more detail.
  • Chest and back plate should match together at the sides with no gap, just a seam line.
  • Shoulder straps should be placed underneath the chest to connect to the back.
For level two certification (if applicable):
For level three certification (if applicable):
  • Shoulder straps should be slotted into the chest into the detail ridges of the top connection points.
501st clone back plate 2.jpg Back Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
  • Rear tank detailed area is painted blue.
  • Chest and back plate should match together at the sides with no gap, just a seam line.
  • Shoulder straps should be placed underneath the chest to connect to the back.
For level two certification (if applicable):
For level three certification (if applicable):
  • Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
  • Highly detailed resin insert should replace softer details.
Clone abb2.jpg Ab Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
  • Ab section should wrap around the wearers body and be sealed at the sides or at the back.
  • Ab section should be completely contained under the chest and back armor.
For level two certification (if applicable):
For level three certification (if applicable):
  • Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.


CLone cod and rear.jpg Cod and Posterior Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Cod and Posterior armor should connect at the hips.
For level two certification (if applicable):
For level three certification (if applicable):
  • Hips should be connected via a snap with the correct detailed shape of the armor at the connection point.


Clone Belt copy.jpg Belt
For 501st approval:
  • Armor should be painted matte or satin white.
  • Ammo Belt with boxes and detonator.
  • Detonator is centered on the back of belt.
  • 8 boxes total, 4 on each side of abdomen and attached to the belt.
For level two certification (if applicable):
For level three certification (if applicable):
  • Belt Boxes should be notched and fitted flush with the details of the belt.
  • Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
  • Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
  • From the rear two belt boxes the belt should have a ribbed detailed appearance.


501st clone thigh armor 2.jpg Thigh Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
  • Rear of the thigh should have an indention.
  • Down the outside of each thigh, there are 2 blue stripes spaced about an inch apart. These stripes line up with the stripes on the calves.
For level two certification (if applicable):
For level three certification (if applicable):
  • Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
[[|150px]] Knee Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Knees should wrap around the front of the leg. From top center a raised detail line should be present.
  • Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
  • There is a blue stripe that follows the bottom curve of the knee plate.
For level two certification (if applicable):
  • Center strap should be primer gray.
  • Connection between the knee and the strapping should have a detail clip.
For level three certification (if applicable):
501st clone shin armor2.jpg Lower Leg Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
  • Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
  • Calf can have an access area on the inside of the leg. The outside of the calf should be closed.
  • Down the outside of each calf , there are 2 blue stripes spaced about an inch apart. These stripes line up with the stripes on the thighs.
For level two certification (if applicable):
For level three certification (if applicable):
  • Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.
Clone shoes copy.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
  • Boots must be lace-less and have flat soles.
  • The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
  • This strap should be white.
  • There should be no markings or labels from the shoe makers. The shoe soles should be gray.
For level two certification (if applicable):
For level three certification (if applicable):


Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.


DC15 carbine.jpg DC-15S Blaster
For 501st approval:

Manufactured by BlasTech Industries the DC-15S is smaller in scale than the DC-15A blaster rifle. Although it has a shorter range than that of the "A" model, it is easier to handle with a higher rate of fire. It features a folding stock for braced firing.

  • Blaster rifle may be scratch built out of plastic, wood, metal or cast in resin.
  • Total length should be approximately 26 “or 66 cm.
  • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • Folding stock (does not need to function).
  • A total of (12) radiator fins are present on the barrel.
  • Spare igniter is present on both sides of barrel.
  • Charge magazine is present on the right side.
For level three certification (if applicable):
  • Charge magazine is metal to gun metal grey in color.
  • Any bolts and screws are metal to gun metal grey in color.
  • Parts of the spare igniter are copper in color.
  • Blaster is weathered.


DC15 rifle.jpg DC-15A Blaster Rifle
For 501st approval:

Manufactured by BlasTech Industries, the DC-15A is a tibanna gas, cartridge powered weapon. Hyper-ionized blue plasma bolts are more than capable of penetrating armored units. Exceptionally effective against both droids and contemporary targets.

  • Blaster rifle is scratch built out of plastic, wood, metal or cast in resin.
  • Total length is approximately 55 inches (139.7 cm).
    • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • A total of (10) radiator fins are present on the barrel.
  • A power setting adjuster is present.
  • The correct style of sniper scope is present.
  • Charge magazine lock is present on the left side.
  • Power setting adjuster, sniper scope and charge magazine lock is metal to gun metal gray in color.
For level three certification (if applicable):
  • Sniper scope is able to be removed from storage position (bottom of rifle) and attached to the top of the rifle.
  • Parts of the spare igniter are copper in color.
  • Front optical sight is able to flip to the up position.
  • Any bolts and screws are metal to gun metal grey in color.
  • Blaster is weathered.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:CT_-_501st_Legion

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.