(Difference between revisions)
(40 intermediate revisions not shown)
Line 1: Line 1:
-
{{CRLheader|501st Clone Trooper|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}
+
{{CRLheader|501st Clone Trooper|File:501st clone trooper front and back3.jpg|CT 11281|D. Roate}}
{{CRLdetinfo| 1111 |501st Clone Trooper|CT|Episode III: Revenge of the Sith|
{{CRLdetinfo| 1111 |501st Clone Trooper|CT|Episode III: Revenge of the Sith|
-
The 501st Legion, later known as "Vader's Fist," was an elite unit of clone troopers commissioned by Supreme Chancellor Palpatine  during the Clone Wars that later became a stormtrooper unit.  The 501st fought in many battles, such as the Battle of Teth and the Battle of Coruscant, becoming one of the most well-known legions.  It was the 501st that was led into the Jedi temple by Darth Vader and helped destroy the Jedi there. In 19 BBY, the 501st became Darth Vader's personal unit as he led them during Operation: Knightfall, in which the clones  helped take down the Jedi, whom they believed to be traitors to the Republic.  }}
 
-
{{CRLwipgmlapproval}}
+
The 501st Legion, later known as "Vader's Fist," is an elite unit of troopers commissioned by Supreme Chancellor Palpatine  during the Clone Wars that later became a Stormtrooper unit.  The 501st have fought in many battles, such as the Battle of Teth and the Battle of Coruscant, becoming one of the most well-known legions.  It was the 501st that was led into the Jedi temple by Darth Vader to helped destroy the Jedi. In 19 BBY, the 501st became Darth Vader's personal unit as he led them during Operation: Knightfall, in which the troopers helped take down the Jedi, whom they believed to be traitors to the Republic.}}
-
{{CRLrequirements}}
+
{{CRLctnlevels}}
 +
 +
{{CRLgmlapproval}}
 +
 +
{{CRLrequirements}}
 +
 +
{{CRLtemplate|File:501st helmet3.jpg|Helmet|
 +
*Phase II style Helmet.
 +
**Fanmade bucket.
 +
**Some "name brand" helmets may be unacceptable.
 +
*Black eye lens.
 +
*Helmet mohawk on dome.
 +
*Starting on the nose of the helmet, there is a blue stripe about 1 inch wide going from the vents to the vocoder. From the middle of the two centermost vents to half an inch off the center eye curves, the area in between is painted pale blue. Continuing from there, widening out to 3 inches from center of the mowhawk, the pale blue stripe continues. It then thins to 4 inches in the rear of the helmet squared off in the back, ¼ inch above the grey helmet wrap.
 +
*Vertical stripes on each side of helmet cheeks that are dark blue in color.
 +
*Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
 +
*Primer grey stripe around back of dome.
 +
*Ear caps are painted a dark grey.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
 +
*Helmet has the appearance of a neck ring.|
 +
*Helmet has an complete enclosed neck ring that seals the helmet to the neck.|}}
 +
 +
{{CRL-realistic-clone-neckseal}}
-
{{CRL-CT-501st-helmet}}  
+
{{CRL-generic-undersuit}}
-
{{CRLtemplate|File:Blankwhite.gif|Neck Seal|
+
{{CRLtemplate-nolevels|File:501st shoulder bells.jpg|Shoulder Armor|
-
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.| |}}
+
*Armor is painted blue.
 +
*Shoulders are tear drop in shape with all rounded edges.
 +
*Shoulders are not symmetrical.  
 +
**The shoulders slightly curve back at the bottom.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.||}}
-
{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
+
{{CRLtemplate-nolevels|File:Clone_Biceps.jpg|Upper Arm Armor|
-
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.| | }}
+
*Armor is painted matte or satin white.
 +
*There is a dimple on the lower area of the back of the arm.
 +
*The outside of the bicep has a hard line edge at the front that turns in.
 +
*The inside of the upper arm is rounded.
 +
*Armor is seamless.
 +
**No visible traces of how the armor was assembled are shown.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.||}}
 +
 +
{{Elbow_Armor_Realistic}}
 +
 +
{{CRLtemplate-onelevel|File:501st gauntlets.jpg|Forearm Armor|
 +
*Armor is painted matte or satin white.
 +
*Both left and right forearms are mirror images of each other.
 +
*Right forearm has a compad with 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
 +
*Forearm tops have a flattened triangular area with a ridge that comes to a point at the top of the forearm.
 +
*The wrist of the forearm has a blue stripe which wraps around the entire circumference of the forearm.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
 +
*Compad has detail antenna on its left.
 +
*Instead of a hard edge the top of the forearm has a bone ridge.
 +
*Armor is seamless.
 +
**No visible traces of how the armor was assembled are shown.|}}
 +
 +
{{Hand_Plates_Realistic}}
 +
 +
{{CRL-generic_black_gloves}}
 +
 +
{{CRLtemplate-nolevels|File:501st chest plate3.jpg|Chest Armor|
 +
*Armor is painted matte or satin white.
 +
*Two detail slots on right raised chest.
 +
*Chest armor has a blue stripe that begins at the center of the neck and extends down the chest to the bottom edge.
 +
**From there it extends out towards the sides.
 +
*Chest and back armor match together at the sides with no open gap.
 +
**A seam line is present.
 +
*Shoulder straps are slotted into the chest into the detail ridges of the top connection points.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.||}}
 +
 +
{{CRLtemplate-onelevel|File:501st back plate3.jpg|Back Armor|
 +
*Armor is painted matte or satin white.
 +
*Rear back has detailed area that contains 4 circles. Under the circles at the left side of the back are two parallel lines and the the right of the back there is a squared detail.
 +
*Rear detail face is painted blue.
 +
*Chest and back armor match together at the sides with no open gap.
 +
**A seam line is present.
 +
*Shoulder straps are slotted into the detail ridges of the top connection points.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
 +
*Highly detailed resin insert replaces softer details.|}}
 +
 +
{{CRLtemplate-onelevel|File:Clone abb2.jpg|Abdomen Armor|
 +
*Armor is painted matte or satin white.
 +
*Four 1/4" diameter holes per side on indents of abdomen.
 +
**Eight holes total.
 +
*Abdomen section wraps around the wearers body and be sealed at the sides or at the back.
 +
*Abdomen armor is completely contained under the chest and back.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
 +
*Abdomen is seamless at the sides and closed in the back.
 +
**A detail plate covers the seam line and hides all work.|}}
-
{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
+
{{CRLtemplate-onelevel|File:CLone cod and rear.jpg|Cod and Posterior Armor|
-
*Armor should be completely painted pale blue.
+
*Realistic style Codpiece and posterior armor.
-
*Shoulders should be tear drop in shape with all rounded edges. | |
+
*Armor is painted matte or satin white.
-
*Shoulder bells should not be symmetrical.  The Shoulder bells should slightly curve back at the bottom of the shoulder. }}
+
*Cod and posterior armor connect at the hips.
 +
*Armor is weathered with shades of grey.|
 +
*Hips have correct detail connector snap and edge feature at the codpiece and posterior side connection.
 +
*Armor is weathered with shades of grey.|}}  
-
{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
+
{{CRLtemplate|File:501st_Belt.jpg|Belt|
-
*Armor should be painted matte or satin white.
+
*Realistic style belt, boxes, and detonator.
-
*Should have a dimple on the lower area of the back of the arm.  The outside of the bicep should have a hard line edge at the front that turns in.  The inside of the upper arm should be rounded.
+
*Belt, boxes and detonator are painted matte or satin White.
-
*Armor should be seamless.  No visible traces of how the armor was assembled should be shown.| | }}
+
*Belt front, between front boxes, has three vertical rectangle indents which are spaced apart by two protruding rectangle areas.
-
 
+
**The rest of the belt is flat surfaced with raised edging on top and bottom that run along the rest of the belt.  
-
{{CRLtemplate|File:Blankwhite.gif|Elbow Armor|
+
*Eight Belt Boxes are attached to Belt, with four on each side.
-
*Armor should be painted matte or satin white.
+
**The two largest Boxes are in front with angled top surface that is higher toward the center.  
-
**At the wrist of the forearms, a wrist stripe that is approximately 1 inch wide should circle the lower cuff. It should be painted pale blue.
+
**The smallest boxes are located behind the front boxes, about 1/8 inch apart and have an angled end on top.  
-
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
+
**The medium sized matching boxes, with flat top cover, are about 1/8 inch from smallest boxes.   
-
* Both elbows have strapping.  The straps should have a raised detail line at the top and bottom of the strap.| |
+
**Left rear box is spaced closer to detonator and has two square buttons in the top left corner, and two dashed indented detail marks on bottom right.
-
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}
+
*Right rear box is spaced closer to detonator and has a bar with two small cylinders centered, and two dashed indented detail marks on bottom left.
-
 
+
*A detonator is centered and attached to back of Belt.
-
{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
+
**Detonator tube is about 2 1/4 inch diameter with wider detailed end caps.
-
*Armor should be painted matte or satin white.
+
**Seven horizontally aligned square buttons are on left side of tube, facing backwards.
-
*Both left and right forearms should be mirror images of each other.
+
**Counting from the left side, buttons 1 - 2 - 5 - 6 are painted blue.
-
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectanular button.
+
*Blue areas are weathered with various scuff marks.
-
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.  
+
*Armor is weathered with shades of grey.|
-
*Armor should be seamless.  No visible traces of how the armor was assembled should be shown. | |
+
*Boxes are notched on back and fit flush to belt.|
-
*Compad has detail antenna on its left.
+
*Back of belt, between rear boxes, has horizontal ribbing.
-
*Instead of a hard edge the top of the forearm has a bone ridge.}}
+
*Detonator has 1/8 to 1/4 inch wide rectangle base, connecting detonator to Belt.}}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
+
{{CRLtemplate-onelevel|File:501st Thigh armor3 copy.jpg|Thigh Armor|
-
*Armor should be painted matte or satin white
+
*Armor is painted matte or satin white.
-
*Hand plates are mirror images of each other.   
+
*Front of thigh armor has a flat triangular area near the knee. From the top of the triangle a ridge line travels up the front of the thigh to the top edge.
-
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}
+
*Rear of the thigh has an indention.
-
 
+
*Down the outside of each thigh, there are (2) blue stripes spaced about an inch apart.
-
{{CRLtemplate|File:Blankwhite.gif|Gloves|
+
**These stripes line up with the stripes on the calves.
-
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}
+
*Blue areas are weathered with various scuff marks.
-
 
+
*Armor is weathered with shades of grey.|
-
{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
+
*Outside of lower portion of the thighs comes to a point and inner lower end is rounded.
-
*Armor should be painted matte or satin white.
+
*Armor is seamless.
-
**The chest has a command stripe that starts 3 inches wide centered in the middle of the chest and widens out to the width of the return curve. From this point the command stripe follows the rib line 1,.5 inch above the return curve to approximately the center of the front two belt boxes. At this point the square off and are do not continue. In the center of the command stripe, a 1 inch thick i mark is made. The dot of the i should be 1.5 inch wide and ½ to ¾ tall and centered just underneath the pectorial meeting vector. The body of the i is just a vertical line that finishes in the rib return curve
+
** No visible traces of how the armor was assembled are shown.|}}
-
*Two detail slots on right breast.
+
-
*Chest and back plate should match together at the sides with no gap, just a seam line.  
+
{{CRLtemplate-onelevel|File:Legion_Style_Knees_Blue.jpg|Knee Armor|
-
*Shoulder straps should be placed underneath the chest to connect to the back. |
+
*Armor is painted matte or satin white.
-
|
+
*Knees wrap around the front of the leg.  From top center a raised detail line is present.
-
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}
+
*Knees are strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
-
 
+
*There is a blue stripe that follows the bottom curve of the knee.
-
{{CRLtemplate|File:Blankwhite.gif|Back Armor|
+
*Blue areas are weathered with various scuff marks.
-
*Armor should be painted matte or satin white.
+
*Armor is weathered with shades of grey.|
-
**The detail plate should be painted pale blue.
+
*Center strap is primer grey.
-
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
+
*Connection between the knee and the strapping has a detail clip.|}}
-
*Chest and back plate should match together at the sides with no gap, just a seam line.
+
-
*Shoulder straps should be placed underneath the chest to connect to the back. |
+
{{CRLtemplate-onelevel|File:501st calfs3.jpg|Lower Leg Armor|
-
|
+
*Armor sis painted matte or satin white.
-
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
+
*Lower Legs are mirror images of each other.
-
*Highly detailed resin insert should replace softer details. }}
+
*The front of the armor has a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
-
 
+
*Back of the lower legs have an indentation just under the calf that extends down to the ankle.
-
{{CRLtemplate|File:Blankwhite.gif|Ab Armor|
+
*The outside of the calf is closed.
-
*Armor should be painted matte or satin white.
+
**Calf can have an access area on the inside of the leg.
-
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
+
*Down the outside of each calf , there are 2 blue stripes spaced about an inch apart.
-
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
+
**These stripes line up with the stripes on the thighs.
-
*Ab section should be completely contained under the chest and back armor. |
+
*Blue areas are weathered with various scuff marks.
-
|
+
*Armor is weathered with shades of grey.|
-
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}
+
*Calves are seamless and have a trap door access through the indent in the rear of the lower leg.|}}
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Cod and Posterior Armor|
+
{{CRL-cloneboots-realistic}}
-
*Armor should be painted matte or satin white.
+
-
*Cod and Posterior armor should connect at the hips. | |
+
-
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}
+
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Belt|
+
-
*Armor should be painted matte or satin white.
+
-
*Ammo Belt with boxes and detonator.
+
-
*Detonator is centered on the back of belt.
+
-
*8 boxes total, 4 on each side of abdomen and attached to the belt. |
+
-
|
+
-
*Belt Boxes should be notched and fitted flush with the details of the belt.
+
-
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
+
-
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
+
-
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}
+
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Thigh Armor|
+
-
*Armor should be painted matte or satin white.
+
-
**There should be two pale blue vertical stripes running center of the outer thighs that are approximately 3/4 inch wide and approximately 1 inch apart.
+
-
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
+
-
*Rear of the thigh should have an indention.
+
-
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. |
+
-
|
+
-
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded. }}
+
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Knee Armor|
+
-
*Armor should be painted matte or satin white.
+
-
**The lower part of the knees should have a V like pale blue stripe.
+
-
*Knees should wrap around the front of the leg.  From top center a raised detail line should be present.
+
-
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
+
-
|
+
-
*Center strap should be primer gray.
+
-
*Connection between the knee and the strapping should have a detail clip.}}
+
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
+
-
*Armor should be painted matte or satin white.
+
-
**There should be two pale blue vertical stripes running center of the outer calves that are approximately 3/4 inch wide and aproximately 1 inch apart.
+
-
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
+
-
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
+
-
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
+
-
|
+
-
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}
+
-
 
+
-
{{CRLtemplate|File:Blankwhite.gif|Boots|
+
-
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles. The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap. There should be no markings or labels from the shoe makers. Boot soles should be primer gray. | | }}
+
{{CRLaccessories}}
{{CRLaccessories}}
-
 
+
{{CRLdc15s-realistic}}
{{CRLdc15s-realistic}}
 +
 +
{{CRLdc15a-realistic}}
-
{{CRLdc15a-realistic}}
+
{{CRLfooter|CTN_CRL|C}}

Revision as of 02:02, 18 July 2014

crlblackhd.gif
501st Clone Trooper
501st clone trooper front and back3.jpg
Model CT 11281, Photo by D. Roate


Clone-Trooper-Detachment.png

Description: 501st Clone Trooper
Prefix: CT
Detachment: Clone Trooper Detachment
Context: Episode III: Revenge of the Sith

The 501st Legion, later known as "Vader's Fist," is an elite unit of troopers commissioned by Supreme Chancellor Palpatine during the Clone Wars that later became a Stormtrooper unit. The 501st have fought in many battles, such as the Battle of Teth and the Battle of Coruscant, becoming one of the most well-known legions. It was the 501st that was led into the Jedi temple by Darth Vader to helped destroy the Jedi. In 19 BBY, the 501st became Darth Vader's personal unit as he led them during Operation: Knightfall, in which the troopers helped take down the Jedi, whom they believed to be traitors to the Republic.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
  • Any uncertainties or questionable aspects of the submitted costume should be brought to the appropriate DL/GML peer review section of the legion forum.
Required Costume Components

The following costume components are present and appear as described below.

501st helmet3.jpg Helmet
For 501st approval:
  • Phase II style Helmet.
    • Fanmade bucket.
    • Some "name brand" helmets may be unacceptable.
  • Black eye lens.
  • Helmet mohawk on dome.
  • Starting on the nose of the helmet, there is a blue stripe about 1 inch wide going from the vents to the vocoder. From the middle of the two centermost vents to half an inch off the center eye curves, the area in between is painted pale blue. Continuing from there, widening out to 3 inches from center of the mowhawk, the pale blue stripe continues. It then thins to 4 inches in the rear of the helmet squared off in the back, ¼ inch above the grey helmet wrap.
  • Vertical stripes on each side of helmet cheeks that are dark blue in color.
  • Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
  • Primer grey stripe around back of dome.
  • Ear caps are painted a dark grey.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Helmet has the appearance of a neck ring.
For level three certification (if applicable):
  • Helmet has an complete enclosed neck ring that seals the helmet to the neck.


Clone trooper neck seal.jpg Neck Seal
For 501st approval:
  • Neck seal is black in color with vertical ribbing or being smooth in appearance.
  • No logos or labels are visible.
    • If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.



TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


501st shoulder bells.jpg Shoulder Armor
For 501st approval:
  • Armor is painted blue.
  • Shoulders are tear drop in shape with all rounded edges.
  • Shoulders are not symmetrical.
    • The shoulders slightly curve back at the bottom.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.


Clone Biceps.jpg Upper Arm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • There is a dimple on the lower area of the back of the arm.
  • The outside of the bicep has a hard line edge at the front that turns in.
  • The inside of the upper arm is rounded.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.



Clone elbow copy.jpg Elbow Armor
For 501st approval:
  • Realistic style elbow armor.
  • Armor is painted matte or satin white.
  • Elbow straps have a raised detail line at the top and bottom of the strap.
  • Armor has two parallel dashed detail slots on each outside edge of elbow at the strap connection.
  • Elbows are mirror images of each other with a notched area on the outside of the elbow above the detail marks.
  • Armor is weathered with shades of grey.


501st gauntlets.jpg Forearm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Both left and right forearms are mirror images of each other.
  • Right forearm has a compad with 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
  • Forearm tops have a flattened triangular area with a ridge that comes to a point at the top of the forearm.
  • The wrist of the forearm has a blue stripe which wraps around the entire circumference of the forearm.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Compad has detail antenna on its left.
  • Instead of a hard edge the top of the forearm has a bone ridge.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.


Clone Hand Guards.jpg Hand Plates
For 501st approval:
  • Realistic style hand plates.
  • Armor is painted matte or satin white
  • Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.
  • Armor is weathered with shades of grey.



Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
  • Gloves cover any exposed skin.
  • Gloves do not show any labels or logos when the armor is worn.


501st chest plate3.jpg Chest Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Two detail slots on right raised chest.
  • Chest armor has a blue stripe that begins at the center of the neck and extends down the chest to the bottom edge.
    • From there it extends out towards the sides.
  • Chest and back armor match together at the sides with no open gap.
    • A seam line is present.
  • Shoulder straps are slotted into the chest into the detail ridges of the top connection points.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.


501st back plate3.jpg Back Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Rear back has detailed area that contains 4 circles. Under the circles at the left side of the back are two parallel lines and the the right of the back there is a squared detail.
  • Rear detail face is painted blue.
  • Chest and back armor match together at the sides with no open gap.
    • A seam line is present.
  • Shoulder straps are slotted into the detail ridges of the top connection points.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Highly detailed resin insert replaces softer details.
Clone abb2.jpg Abdomen Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Four 1/4" diameter holes per side on indents of abdomen.
    • Eight holes total.
  • Abdomen section wraps around the wearers body and be sealed at the sides or at the back.
  • Abdomen armor is completely contained under the chest and back.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Abdomen is seamless at the sides and closed in the back.
    • A detail plate covers the seam line and hides all work.
CLone cod and rear.jpg Cod and Posterior Armor
For 501st approval:
  • Realistic style Codpiece and posterior armor.
  • Armor is painted matte or satin white.
  • Cod and posterior armor connect at the hips.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Hips have correct detail connector snap and edge feature at the codpiece and posterior side connection.
  • Armor is weathered with shades of grey.
501st Belt.jpg Belt
For 501st approval:
  • Realistic style belt, boxes, and detonator.
  • Belt, boxes and detonator are painted matte or satin White.
  • Belt front, between front boxes, has three vertical rectangle indents which are spaced apart by two protruding rectangle areas.
    • The rest of the belt is flat surfaced with raised edging on top and bottom that run along the rest of the belt.
  • Eight Belt Boxes are attached to Belt, with four on each side.
    • The two largest Boxes are in front with angled top surface that is higher toward the center.
    • The smallest boxes are located behind the front boxes, about 1/8 inch apart and have an angled end on top.
    • The medium sized matching boxes, with flat top cover, are about 1/8 inch from smallest boxes.
    • Left rear box is spaced closer to detonator and has two square buttons in the top left corner, and two dashed indented detail marks on bottom right.
  • Right rear box is spaced closer to detonator and has a bar with two small cylinders centered, and two dashed indented detail marks on bottom left.
  • A detonator is centered and attached to back of Belt.
    • Detonator tube is about 2 1/4 inch diameter with wider detailed end caps.
    • Seven horizontally aligned square buttons are on left side of tube, facing backwards.
    • Counting from the left side, buttons 1 - 2 - 5 - 6 are painted blue.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Boxes are notched on back and fit flush to belt.
For level three certification (if applicable):
  • Back of belt, between rear boxes, has horizontal ribbing.
  • Detonator has 1/8 to 1/4 inch wide rectangle base, connecting detonator to Belt.
501st Thigh armor3 copy.jpg Thigh Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Front of thigh armor has a flat triangular area near the knee. From the top of the triangle a ridge line travels up the front of the thigh to the top edge.
  • Rear of the thigh has an indention.
  • Down the outside of each thigh, there are (2) blue stripes spaced about an inch apart.
    • These stripes line up with the stripes on the calves.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Outside of lower portion of the thighs comes to a point and inner lower end is rounded.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
Legion Style Knees Blue.jpg Knee Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Knees wrap around the front of the leg. From top center a raised detail line is present.
  • Knees are strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
  • There is a blue stripe that follows the bottom curve of the knee.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Center strap is primer grey.
  • Connection between the knee and the strapping has a detail clip.
501st calfs3.jpg Lower Leg Armor
For 501st approval:
  • Armor sis painted matte or satin white.
  • Lower Legs are mirror images of each other.
  • The front of the armor has a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
  • Back of the lower legs have an indentation just under the calf that extends down to the ankle.
  • The outside of the calf is closed.
    • Calf can have an access area on the inside of the leg.
  • Down the outside of each calf , there are 2 blue stripes spaced about an inch apart.
    • These stripes line up with the stripes on the thighs.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Calves are seamless and have a trap door access through the indent in the rear of the lower leg.


Clone shoes copy.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle.
  • Boots are lace-less.
  • The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
  • There are no markings or labels from the shoe makers.
  • Boot soles are flat.
  • Boot soles are colored primer grey.


Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.


DC15 carbine.jpg DC-15S Blaster
For 501st approval:

Manufactured by BlasTech Industries the DC-15S is smaller in scale than the DC-15A blaster rifle. Although it has a shorter range than that of the "A" model, it is easier to handle with a higher rate of fire. It features a folding stock for braced firing.

  • Realistic Clone Style DC-15S Blaster.
  • Blaster may be scratch built out of plastic, wood, metal or cast in resin.
  • Blaster has realistic Episode II or Episode III details:
    • Wire frame sight.
    • Folding stock.
    • (12) radiator fins evenly spaced along the length of barrel.
    • Igniter detail knobs.
    • Charge magazine clip on right side.
  • Total length is approximately 26“ (66 cm).
  • Because of the scale, the Hasbro version is incorrect.
For level two certification (if applicable):
  • Charge magazine detail on clip is metal to gun metal grey in color.
  • Detail bolts and screws are metal to gun metal grey in color.
  • Igniter knobs have some copper coloring.
  • Blaster is weathered.
For level three certification (if applicable):
  • Functioning Blue LED is installed in barrel.


DC15 rifle.jpg DC-15A Blaster Rifle
For 501st approval:

Manufactured by BlasTech Industries, the DC-15A is a tibanna gas, cartridge powered weapon. Hyper-ionized blue plasma bolts are more than capable of penetrating armored units. Exceptionally effective against both droids and contemporary targets.

  • Realistic Clone Style DC-15A Blaster Rifle.
  • Blaster rifle is scratch built out of plastic, wood, metal or cast in resin.
  • Blaster has realistic Episode II or Episode III details:
    • Flip up sight in down position.
    • (10) radiator fins evenly spaced along the length of barrel.
    • Power setting adjuster detail lever.
    • Sniper Scope attached under rifle in storage position.
    • Charge magazine clip on left side.
    • Igniter detail knobs.
  • Total length is approximately 55 inches (139.7 cm).
  • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • Charge magazine detail on clip is metal to gun metal grey in color.
  • Detail bolts and screws are metal to gun metal grey in color.
  • Igniter has some copper coloring.
  • Power setting adjuster detail lever is metal or gun metal grey.
  • Sniper scope is metal or gun metal grey.
  • Blaster is weathered.
For level three certification (if applicable):
  • Functioning Blue LED is installed in barrel.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:CT_-_501st_Legion

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.