Revision as of 11:12, 25 March 2012 by Darren1970 (Talk | contribs)
crlblackhd.gif
41st Elite Clone Trooper
Missingprofile.jpg
Model MODEL NAME, Photo by PHOTOGRAPHER NAME


Clone-Trooper-Detachment.png

Description: 41st Elite Clone Trooper
Prefix: CT
Detachment: Clone Trooper Detachment
Context: Episode III: Revenge of the Sith
The 41st Elite Corps was a legion of elite clones in the Grand Army of the Republic, composed of many variants of troopers including AT-RT drivers and BARC troopers. Their legion color was gray and white. The 41st Elite was a division out of the 9th Assault Corps, under command of Senior Jedi General Luminara Unduli and Senior Clone Commander Gree.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

  • This CRL is a work in progress.
  • This costume may be approved by GMLs, but until the library entry is complete, it is suggested that this character first be submitted to the appropriate DL/GML peer review section of the legion forum.
  • If you have this costume and would like to assist with the completion of this library entry, please contact your detachment leader.
  • Please note that the use of the word "should" below does not indicate that the armor piece is considered open to interpretation. All instances of "should be" and "should have" will be replaced with "is" and "has", as this guide is completed.
Required Costume Components

The following costume components are present and appear as described below.

ROTS41st helmet.jpg Helmet
For 501st approval:
  • Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
  • Visor - Black Visor.
  • Helmet mohawk on dome.
  • Vertical kill stripes on each side of helmet cheeks that are dark blue in color.
  • Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
  • Primer grey stripe around back of dome.
  • Ear caps are painted a dark grey.
For level two certification (if applicable):
  • Helmet has the appearance of a neck ring.
For level three certification (if applicable):
  • Helmet has an enclosed complete neck ring that seals the helmet to the neck.
Blankwhite.gif Neck Seal
For 501st approval:
  • Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.
For level two certification (if applicable):
For level three certification (if applicable):
TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.
For level two certification (if applicable):
For level three certification (if applicable):
ROTS41st shoulders.jpg Shoulder Bells
For 501st approval:
  • Armor should be painted primer gray.
  • Shoulders should be tear drop in shape with all rounded edges.
For level two certification (if applicable):
For level three certification (if applicable):
  • Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder.
ROTS41st biceps.jpg Upper Arm Armor
For 501st approval:
  • Armor should be painted matte or satin white.
    • Approximately 1 inch from the top of the upper arm a 1 inch gray stripe should encircle the entire upper arm.
      • Optional paint addition - 5 horizontal approximate 3/4 inch by approximate 2inch primer gray bars.
  • Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):
For level three certification (if applicable):
ROTS41st elbows.jpg Elbow Armor
For 501st approval:
  • Armor should be painted matte or satin white
  • There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
  • Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.
For level two certification (if applicable):
For level three certification (if applicable):
  • Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.
ROTS41st forearms.jpg Forearm Armor
For 501st approval:
  • Armor should be painted matte or satin white.
    • Approximately 1 inch from the top of the forearm a 1 inch gray stripe should encircle the entire forearm.
  • Both left and right forearms should be mirror images of each other.
  • Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectanular button.
  • Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):
For level three certification (if applicable):
  • Compad has detail antenna on its left.
  • Instead of a hard edge the top of the forearm has a bone ridge.
Blankwhite.gif Hand Plates
For 501st approval:
  • Armor should be painted primer gray.
  • Hand plates are mirror images of each other.
  • Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Chest Armor
For 501st approval:
  • Armor should be painted matte or satin white.
    • Four vertical primer gray hash marks should be on the right chest next to the detail slots. Following the edge of the shoulder straps a 1 inch wide primer gray stripe should follow to the lower part of the chest and then follow the underarm curve.
  • Two detail slots on right breast.
  • Chest and back plate should match together at the sides with no gap, just a seam line.
  • Shoulder straps should be placed underneath the chest to connect to the back.
For level two certification (if applicable):

For level three certification (if applicable):
  • Shoulder straps should be slotted into the chest into the detail ridges of the top connection points.
Blankwhite.gif Back Armor
For 501st approval:
  • Armor should be painted matte or satin white.
    • A one inch primer gray stripe should continue from the the chest and back connection and curve back around and end at the rear under arm opening.
  • Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
  • Chest and back plate should match together at the sides with no gap, just a seam line.
  • Shoulder straps should be placed underneath the chest to connect to the back.
For level two certification (if applicable):

For level three certification (if applicable):
  • Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
  • Highly detailed resin insert should replace softer details.
Blankwhite.gif Ab Armor
For 501st approval:
  • Armor should be painted primer gray.
  • Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
  • Ab section should wrap around the wearers body and be sealed at the sides or at the back.
  • Ab section should be completely contained under the chest and back armor.
For level two certification (if applicable):

For level three certification (if applicable):
  • Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.
Blankwhite.gif Cod and Posterior Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Cod and Posterior armor should connect at the hips.
For level two certification (if applicable):
For level three certification (if applicable):
  • Hips should be connected via a snap with the correct detailed shape of the armor at the connection point.
Blankwhite.gif Belt
For 501st approval:
  • Armor should be painted primer gray.
  • Ammo Belt with boxes and detonator.
  • Detonator is centered on the back of belt.
  • 8 boxes total, 4 on each side of abdomen and attached to the belt.
For level two certification (if applicable):

For level three certification (if applicable):
  • Belt Boxes should be notched and fitted flush with the details of the belt.
  • Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
  • Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
  • From the rear two belt boxes the belt should have a ribbed detailed appearance.
Blankwhite.gif Thigh Armor
For 501st approval:
  • Armor should be painted matte or satin white.
    • Approximately 1 inch from the top of the thigh a 1 inch gray stripe should encircle the entire thigh.
  • Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
  • Rear of the thigh should have an indention.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):

For level three certification (if applicable):
  • Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.
Blankwhite.gif Knee Armor
For 501st approval:
  • Armor should be painted matte or satin white.
    • The lower part of the knees should have a V like primer gray stripe.
  • Knees should wrap around the front of the leg. From top center a raised detail line should be present.
  • Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
For level two certification (if applicable):

For level three certification (if applicable):
  • Center strap should be primer gray.
  • Connection between the knee and the strapping should have a detail clip.
Blankwhite.gif Lower Leg Armor
For 501st approval:
  • Armor should be painted primer gray.
  • Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
  • Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
  • Calf can have an access area on the inside of the leg. The outside of the calf should be closed.
For level two certification (if applicable):

For level three certification (if applicable):
  • Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.
Blankwhite.gif Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles. The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap. There should be no markings or labels from the shoe makers. Boot soles should be primer gray.
For level two certification (if applicable):
For level three certification (if applicable):
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.


DC15 carbine.jpg DC-15S Blaster
For 501st approval:

Manufactured by BlasTech Industries the DC-15S is smaller in scale than the DC-15A blaster rifle. Although it has a shorter range than that of the "A" model, it is easier to handle with a higher rate of fire. It features a folding stock for braced firing.

  • Realistic Clone Style DC-15S Blaster.
  • Blaster may be scratch built out of plastic, wood, metal or cast in resin.
  • Blaster has realistic Episode II or Episode III details:
    • Wire frame sight.
    • Folding stock.
    • (12) radiator fins evenly spaced along the length of barrel.
    • Igniter detail knobs.
    • Charge magazine clip on right side.
  • Total length is approximately 26“ (66 cm).
  • Because of the scale, the Hasbro version is incorrect.
For level two certification (if applicable):
  • Charge magazine detail on clip is metal to gun metal grey in color.
  • Detail bolts and screws are metal to gun metal grey in color.
  • Igniter knobs have some copper coloring.
  • Blaster is weathered.
For level three certification (if applicable):
  • Functioning Blue LED is installed in barrel.


DC15 rifle.jpg DC-15A Blaster Rifle
For 501st approval:

Manufactured by BlasTech Industries, the DC-15A is a tibanna gas, cartridge powered weapon. Hyper-ionized blue plasma bolts are more than capable of penetrating armored units. Exceptionally effective against both droids and contemporary targets.

  • Realistic Clone Style DC-15A Blaster Rifle.
  • Blaster rifle is scratch built out of plastic, wood, metal or cast in resin.
  • Blaster has realistic Episode II or Episode III details:
    • Flip up sight in down position.
    • (10) radiator fins evenly spaced along the length of barrel.
    • Power setting adjuster detail lever.
    • Sniper Scope attached under rifle in storage position.
    • Charge magazine clip on left side.
    • Igniter detail knobs.
  • Total length is approximately 55 inches (139.7 cm).
  • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • Charge magazine detail on clip is metal to gun metal grey in color.
  • Detail bolts and screws are metal to gun metal grey in color.
  • Igniter has some copper coloring.
  • Power setting adjuster detail lever is metal or gun metal grey.
  • Sniper scope is metal or gun metal grey.
  • Blaster is weathered.
For level three certification (if applicable):
  • Functioning Blue LED is installed in barrel.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.