(Difference between revisions)
 
(26 intermediate revisions not shown)
Line 1: Line 1:
-
{{CRLheader|41st Elite Clone Trooper|File:ROTS41st_model.jpg|CT6218|Paul Tizzano}}
+
{{CRLheader|41st Elite Corps|File:ROTS41st_model.jpg|CT 6218|Paul Tizzano}}
-
{{CRLdetinfo| 1111 |41st Elite Clone Trooper|CT|Episode III: Revenge of the Sith|
+
{{CRLdetinfo| 1111 |41st Elite Corps|CT|Episode III: Revenge of the Sith|
-
The 41st Elite Corps was a legion of elite clones in the Grand Army of the Republic, composed of many variants of troopers including AT-RT drivers and BARC troopers.  Their legion color was gray and white. The 41st Elite was a division out of the 9th Assault Corps, under command of Senior Jedi General Luminara Unduli and Senior Clone Commander Gree. }}
+
 
 +
The 41st Elite Corps includes several types of troopers and is formed by the combined forces of Sarlacc Battalion A, Battalion B, and Green Company.
 +
The 41st specializes in operations performed on alien planets or under extreme conditions. Shown here is their grey and white armor scheme.}}
{{CRLctnlevels}}
{{CRLctnlevels}}
-
{{CRLwipgmlapproval}}
+
{{CRLgmlapproval}}
{{CRLrequirements}}
{{CRLrequirements}}
{{CRLtemplate|File:E3 Clone Helmet.jpg| Helmet|
{{CRLtemplate|File:E3 Clone Helmet.jpg| Helmet|
-
*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
+
*Phase II style Clone Helmet.
-
*Visor - Black Visor.
+
**Some "name brand" helmets may be unacceptable.
*Helmet mohawk on dome.
*Helmet mohawk on dome.
-
*Vertical kill stripes on each side of helmet cheeks that are dark blue in color.
+
*Black eye lens.
-
*Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
+
*Helmet frown is charcoal grey in color.
 +
*Vertical hash marks on each side of helmet cheeks are a dark blue color.
 +
**Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
 +
*Ear caps are painted a dark grey
*Primer grey stripe around back of dome.
*Primer grey stripe around back of dome.
-
*Ear caps are painted a dark grey.|
+
*Grey areas are weathered with various scuff marks.
-
*Helmet has the appearance of a neck ring. |
+
*Armor is weathered with shades of grey.|
-
*Helmet has an enclosed complete neck ring that seals the helmet to the neck. }}
+
*Helmet has the appearance of a neck ring.|
 +
*Helmet has an enclosed complete neck ring that seals the helmet to the neck.}}
-
{{CRLtemplate|File:Clone trooper neck seal.jpg|Neck Seal|
+
{{CRL-realistic-clone-neckseal}}
-
*Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.| |}}
+
-
{{CRLtemplate|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
+
{{CRLtemplate-nolevels|File:TK_anh_stunt_undersuit.jpeg|Under Suit|
-
* Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.| | }}
+
*Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.||}}
-
{{CRLtemplate|File:ROTS41st_shoulders.jpg|Shoulder Bells|
+
{{CRLtemplate-onelevel|File:ROTS41st_shoulders.jpg|Shoulder Armor|
-
*Armor should be painted primer gray.
+
*Armor is painted primer grey.
-
*Shoulders should be tear drop in shape with all rounded edges. | |
+
*Shoulders are tear drop in shape with all rounded edges.|
-
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}
+
*Shoulders are not symmetrical.
 +
**The armor slightly curves back at the bottom of the shoulder.
 +
*Grey areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|}}
-
{{CRLtemplate|File:ROTS41st_biceps.jpg|Upper Arm Armor|
+
{{CRLtemplate-nolevels|File:ROTS41st_biceps.jpg|Upper Arm Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
**Approximately 1 inch from the top of the upper arm a 1 inch gray stripe should encircle the entire upper arm.
+
**Approximately 1 inch from the top of the upper arm, a 1 inch grey stripe encircles the entire arm.
-
***Optional paint addition - 5 horizontal approximate 3/4 inch by approximate 2inch primer gray bars.
+
**Optional paint addition: 5 horizontal primer grey bars, approximately 3/4 inch by 2 inches.
-
*Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.
+
*There is a dimple on the lower area of the back of the arm.
-
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.| | }}
+
*The outside of the bicep has a hard line edge at the front that turns in.
 +
*The inside of the upper arm is rounded.
 +
*Armor is seamless.
 +
**No visible traces of how the armor was assembled are shown.
 +
*Grey areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.||}}
-
{{CRLtemplate|File:Clone elbow copy.jpg|Elbow Armor|
+
{{Elbow_Armor_Realistic}}
-
*Armor should be painted matte or satin white
+
-
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
+
-
* Both elbows have strapping.  The straps should have a raised detail line at the top and bottom of the strap.| |
+
-
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}
+
-
{{CRLtemplate|File:ROTS41st_forearms.jpg|Forearm Armor|
+
{{CRLtemplate-onelevel|File:ROTS41st_forearms.jpg|Forearm Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
**Approximately 1 inch from the top of the forearm a 1 inch gray stripe should encircle the entire forearm.
+
*Approximately 1 inch from the top of the forearm a 1 inch grey stripe encircles the entire forearm.
-
*Both left and right forearms should be mirror images of each other.
+
*Both left and right forearms are mirror images of each other.
-
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectanular button.
+
*Right forearm has a compad with 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
-
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.  
+
*Forearm tops have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
-
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |
+
*Armor is seamless.
 +
**No visible traces of how the armor was assembled are shown.
 +
*Grey areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
*Compad has detail antenna on its left.  
*Compad has detail antenna on its left.  
-
*Instead of a hard edge the top of the forearm has a bone ridge.}}
+
*Instead of a hard edge the top of the forearm has a bone ridge.|}}
-
{{CRLtemplate|File:ROTS41st_handplates.jpg|Hand Plates|
+
{{CRLtemplate-nolevels|File:ROTS41st_handplates.jpg|Hand Plates|
-
*Armor should be painted primer gray.
+
*Armor is painted primer grey.
*Hand plates are mirror images of each other.   
*Hand plates are mirror images of each other.   
-
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}
+
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.
 +
*Grey areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.||}}
-
{{CRLtemplate|File:generic-black-gloves.jpg|Gloves|
+
{{CRLtemplate-nolevels|File:Generic-black-gloves.jpg|Gloves|
-
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}
+
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves do not show any labels or logos once the armor is on and cover any exposed skin.||}}
-
{{CRLtemplate|File:ROTS41st_chest.jpg|Chest Armor|
+
{{CRLtemplate-nolevels|File:ROTS41st_chest.jpg|Chest Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
**Four vertical primer gray hash marks should be on the right chest next to the detail slots. Following the edge of the shoulder straps a 1 inch wide primer gray stripe should follow to the lower part of the chest and then follow the underarm curve.
+
*Two detail slots on right raised chest area.
-
*Two detail slots on right breast.
+
*Four vertical primer grey hash marks are located the right chest next to the detail slots.
-
*Chest and back plate should match together at the sides with no gap, just a seam line.  
+
*Following the edge of the shoulder straps, a 1 inch wide primer grey stripe extends to the lower part of the chest and then follows the underarm curve.
-
*Shoulder straps should be placed underneath the chest to connect to the back. |
+
*Chest and back armor match together at the sides with no open gap.
-
|
+
**A seam line is present.
-
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}
+
*Shoulder straps are slotted into the detail ridges of the top connection points.
 +
*Grey areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.||}}
-
{{CRLtemplate|File:ROTS41st_back2.jpg|Back Armor|
+
{{CRLtemplate-onelevel|File:ROTS41st_back2.jpg|Back Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
**A one inch primer gray stripe should continue from the the chest and back connection and curve back around and end at the rear under arm opening.  
+
*The previous one inch primer grey stripe continues from the side of the chest armor onto and back, curves upward, and ends at the rear under arm opening.
-
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
+
*Rear center plate has detailed area that contains 4 circles.
-
*Chest and back plate should match together at the sides with no gap, just a seam line.  
+
**Under the circles at the left side of the back there are two parallel lines.
-
*Shoulder straps should be placed underneath the chest to connect to the back.
+
**On the right side of the back there is a squared detail.
-
*A optional radio pack may be added if desired. If present, the radio pack should match one of the styles seen on screen ("slimline" or "full sized" versions) |
+
*Chest and back armor match together at the sides with no open gap.
-
|
+
**A seam line is present.
-
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
+
*Shoulder straps are slotted into the detail ridges of the top connection points.
-
*Highly detailed resin insert should replace softer details. }}
+
*Grey areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.
 +
***Back armor shown with optional Radio Pack.
 +
***See "Optional Accessories" below.|
 +
*Highly detailed resin insert replaces softer details.|}}
-
{{CRLtemplate|File:ROTS41st_ab.jpg|Ab Armor|
+
{{CRLtemplate-onelevel|File:41st_Abdomen.jpg|Abdomen Armor|
-
*Armor should be painted primer gray.
+
*Armor is painted primer grey.
-
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
+
*Four 1/4" diameter holes per side on indents of abdomen.
-
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
+
**Eight holes total.
-
*Ab section should be completely contained under the chest and back armor. |
+
*Abdomen section wraps around the wearers body and is sealed at the sides or back.
-
|
+
*Abdomen armor is completely contained under the chest and back armor.
-
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}
+
*Grey areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
 +
*Armor is seamless at the sides and closed in the back.
 +
**A detail plate covers the seam line and hides all work.|}}
-
{{CRLtemplate|File:Bacara_codbutt.jpg|Cod and Posterior Armor|
+
{{CRLtemplate-onelevel|File:CLone cod and rear.jpg|Codpiece and Posterior Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
*Cod and Posterior armor should connect at the hips. | |
+
*Codpiece and Posterior armor connect at the hips.|
-
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}
+
*Hips are connected via a snap with the correct detailed shape of the armor at the connection point.|}}
-
{{CRLtemplate|File:ROTS41st_belt.jpg|Belt|
+
{{CRLtemplate-onelevel|File:ROTS41st_belt.jpg|Belt|
-
*Armor should be painted primer gray.
+
*Armor is painted primer grey.
-
*Ammo Belt with boxes and detonator.
+
*Ammo Belt includes belt boxes and rear detonator.
-
*Detonator is centered on the back of belt.  
+
**(8 )boxes total are attached to the belt.
-
*8 boxes total, 4 on each side of abdomen and attached to the belt. |
+
**(4) on each side of abdomen.
-
|
+
*Detonator is centered on the back of belt.|
-
*Belt Boxes should be notched and fitted flush with the details of the belt.
+
*Belt Boxes are notched and fitted flush with the details of the belt.
-
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
+
*Left Rear belt box has two square buttons in the top left corner and an equal symbol detail at the bottom right.
-
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
+
*Right Rear belt box has a bar with two small cylinders centered with an equal symbol detail on the bottom left.
-
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}
+
*From the rear two belt boxes the belt has a ribbed detailed appearance.|}}
-
{{CRLtemplate|File:ROTS41st_thighs.jpg|Thigh Armor|
+
{{CRLtemplate-onelevel|File:ROTS41st_thighs.jpg|Thigh Armor|
-
*Armor should be painted matte or satin white.  
+
*Armor is painted matte or satin white.
-
**Approximately 1 inch from the top of the thigh a 1 inch gray stripe should encircle the entire thigh.
+
**Approximately 1 inch from the top of the upper edge, a 1 inch grey stripe encircles the entire thigh.
-
* Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
+
*Front of thigh armor has a flat triangular area near the knee.
-
*Rear of the thigh should have an indention.
+
**From the top of the triangle, a ridge line travels up the front of the thigh to the top edge.
-
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. |
+
*Rear of the thigh has an indention.
-
|
+
*Armor is seamless.
-
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded. }}
+
**No visible traces of how the armor was assembled are shown.|
 +
*Outside lower edge of the thigh comes to a point.
 +
**Inner lower edge is rounded.|}}
-
{{CRLtemplate|File:ROTS41st_knees.jpg|Knee Armor|
+
{{CRLtemplate-onelevel|File:ROTS41st_knees.jpg|Knee Armor|
-
*Armor should be painted matte or satin white.
+
*Realistic style knee armor.
-
**The lower part of the knees should have a V like primer gray stripe.
+
*Armor is panted matte or satin white.
-
*Knees should wrap around the front of the leg.  From top center a raised detail line should be present.
+
*Grey "V' -shape stripe follows the bottom edge of knee armor.
-
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
+
*Knees have a protruding flat area in front oriented towards the top of Knee.
-
|
+
*Knees bend around the front and connect to white detail clips that connect the strap on each side.
-
*Center strap should be primer gray.
+
*A white colored flat strap, about 2 inches wide, wraps around back of leg.
-
*Connection between the knee and the strapping should have a detail clip.}}
+
*Grey areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
 +
*Flat Strap has raised 5/8 Inch wide grey center strap.|}}
-
{{CRLtemplate|File:ROTS41st_shins.jpg|Lower Leg Armor|
+
{{CRLtemplate-onelevel|File:ROTS41st_shins.jpg|Lower Leg Armor|
-
*Armor should be painted primer gray.
+
*Armor is painted primer grey.
-
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
+
*Lower Legs are mirror images of each other.
-
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
+
*The front of the armor has a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
-
*Calf can have an access area on the inside of the leg.  The outside of the calf should be closed. |
+
*Back of the lower legs have an indentation just under the calf that extends down to the ankle.
-
|
+
*The outside of the calf is seamless.
-
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}
+
**A clam shell opening on the inner seam is acceptable.
 +
*Grey areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
 +
*Armor is seamless with a trap door access through the indent in the rear of the lower leg.|}}
-
{{CRLtemplate|File:Clone shoes copy.jpg|Boots|
+
{{CRL-cloneboots-realistic}}
-
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles. The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap. There should be no markings or labels from the shoe makers. Boot soles should be primer gray. | | }}
+
{{CRLaccessories}}
{{CRLaccessories}}
 +
 +
{{CRLtemplate-nolevels|File:ROTS41st_Backpack.jpg|Radio Pack|
 +
*The radio pack matches either the "slimline" or "full sized" version.
 +
*Radio is painted matte or satin black.
 +
*Radio consists of a horizontal top plate and vertical face plate.
 +
*Radio has an antenna mounted on top left.
 +
*There is a small curl knob near the antenna base.
 +
*Radio has a static bar on front face that bends back at two 90 degree angles to attach to side of the radio.
 +
*Radio has 3 knobs, dials, or lights on the bottom right corner.||}}
 +
 +
{{CRLtemplate-onelevel|File:41st_Back02.jpg|Radio Box Back Armor|
 +
*Radio Box Back Armor is used as an alternate to the standard back armor.
 +
**Radio Pack is not used with this style back armor.
 +
*Armor is painted matte or satin white.
 +
*The previous one inch primer grey stripe continues from the side of the chest armor onto and back, curves upward, and ends at the rear under arm opening.
 +
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there are two parallel lines and the the right of the back there is a squared detail.
 +
*Top of the tank has a thermal detonator with three buttons.
 +
*in the recess under the back tank, there are two radio boxes.
 +
*Chest and back armor match together at the sides with no open gap.
 +
**A seam line is present.
 +
*Shoulder straps are placed underneath the chest to connect to the back.|
 +
*Shoulder straps are slotted into the back armor, into the detail ridges of the top connection points.
 +
*Highly detailed resin insert should replace softer details.|}}
{{CRLdc15s-realistic}}
{{CRLdc15s-realistic}}

Latest revision as of 20:40, 8 July 2014

crlblackhd.gif
41st Elite Corps
ROTS41st model.jpg
Model CT 6218, Photo by Paul Tizzano


Clone-Trooper-Detachment.png

Description: 41st Elite Corps
Prefix: CT
Detachment: Clone Trooper Detachment
Context: Episode III: Revenge of the Sith

The 41st Elite Corps includes several types of troopers and is formed by the combined forces of Sarlacc Battalion A, Battalion B, and Green Company. The 41st specializes in operations performed on alien planets or under extreme conditions. Shown here is their grey and white armor scheme.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
  • Any uncertainties or questionable aspects of the submitted costume should be brought to the appropriate DL/GML peer review section of the legion forum.
Required Costume Components

The following costume components are present and appear as described below.

E3 Clone Helmet.jpg Helmet
For 501st approval:
  • Phase II style Clone Helmet.
    • Some "name brand" helmets may be unacceptable.
  • Helmet mohawk on dome.
  • Black eye lens.
  • Helmet frown is charcoal grey in color.
  • Vertical hash marks on each side of helmet cheeks are a dark blue color.
    • Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
  • Ear caps are painted a dark grey
  • Primer grey stripe around back of dome.
  • Grey areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Helmet has the appearance of a neck ring.
For level three certification (if applicable):
  • Helmet has an enclosed complete neck ring that seals the helmet to the neck.


Clone trooper neck seal.jpg Neck Seal
For 501st approval:
  • Neck seal is black in color with vertical ribbing or being smooth in appearance.
  • No logos or labels are visible.
    • If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.


TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


ROTS41st shoulders.jpg Shoulder Armor
For 501st approval:
  • Armor is painted primer grey.
  • Shoulders are tear drop in shape with all rounded edges.
For level two certification (if applicable):
  • Shoulders are not symmetrical.
    • The armor slightly curves back at the bottom of the shoulder.
  • Grey areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
ROTS41st biceps.jpg Upper Arm Armor
For 501st approval:
  • Armor is painted matte or satin white.
    • Approximately 1 inch from the top of the upper arm, a 1 inch grey stripe encircles the entire arm.
    • Optional paint addition: 5 horizontal primer grey bars, approximately 3/4 inch by 2 inches.
  • There is a dimple on the lower area of the back of the arm.
  • The outside of the bicep has a hard line edge at the front that turns in.
  • The inside of the upper arm is rounded.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
  • Grey areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.



Clone elbow copy.jpg Elbow Armor
For 501st approval:
  • Realistic style elbow armor.
  • Armor is painted matte or satin white.
  • Elbow straps have a raised detail line at the top and bottom of the strap.
  • Armor has two parallel dashed detail slots on each outside edge of elbow at the strap connection.
  • Elbows are mirror images of each other with a notched area on the outside of the elbow above the detail marks.
  • Armor is weathered with shades of grey.


ROTS41st forearms.jpg Forearm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Approximately 1 inch from the top of the forearm a 1 inch grey stripe encircles the entire forearm.
  • Both left and right forearms are mirror images of each other.
  • Right forearm has a compad with 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
  • Forearm tops have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
  • Grey areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Compad has detail antenna on its left.
  • Instead of a hard edge the top of the forearm has a bone ridge.
ROTS41st handplates.jpg Hand Plates
For 501st approval:
  • Armor is painted primer grey.
  • Hand plates are mirror images of each other.
  • Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.
  • Grey areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.


Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves do not show any labels or logos once the armor is on and cover any exposed skin.


ROTS41st chest.jpg Chest Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Two detail slots on right raised chest area.
  • Four vertical primer grey hash marks are located the right chest next to the detail slots.
  • Following the edge of the shoulder straps, a 1 inch wide primer grey stripe extends to the lower part of the chest and then follows the underarm curve.
  • Chest and back armor match together at the sides with no open gap.
    • A seam line is present.
  • Shoulder straps are slotted into the detail ridges of the top connection points.
  • Grey areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.


ROTS41st back2.jpg Back Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • The previous one inch primer grey stripe continues from the side of the chest armor onto and back, curves upward, and ends at the rear under arm opening.
  • Rear center plate has detailed area that contains 4 circles.
    • Under the circles at the left side of the back there are two parallel lines.
    • On the right side of the back there is a squared detail.
  • Chest and back armor match together at the sides with no open gap.
    • A seam line is present.
  • Shoulder straps are slotted into the detail ridges of the top connection points.
  • Grey areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
      • Back armor shown with optional Radio Pack.
      • See "Optional Accessories" below.
For level two certification (if applicable):
  • Highly detailed resin insert replaces softer details.
41st Abdomen.jpg Abdomen Armor
For 501st approval:
  • Armor is painted primer grey.
  • Four 1/4" diameter holes per side on indents of abdomen.
    • Eight holes total.
  • Abdomen section wraps around the wearers body and is sealed at the sides or back.
  • Abdomen armor is completely contained under the chest and back armor.
  • Grey areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Armor is seamless at the sides and closed in the back.
    • A detail plate covers the seam line and hides all work.
CLone cod and rear.jpg Codpiece and Posterior Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Codpiece and Posterior armor connect at the hips.
For level two certification (if applicable):
  • Hips are connected via a snap with the correct detailed shape of the armor at the connection point.
ROTS41st belt.jpg Belt
For 501st approval:
  • Armor is painted primer grey.
  • Ammo Belt includes belt boxes and rear detonator.
    • (8 )boxes total are attached to the belt.
    • (4) on each side of abdomen.
  • Detonator is centered on the back of belt.
For level two certification (if applicable):
  • Belt Boxes are notched and fitted flush with the details of the belt.
  • Left Rear belt box has two square buttons in the top left corner and an equal symbol detail at the bottom right.
  • Right Rear belt box has a bar with two small cylinders centered with an equal symbol detail on the bottom left.
  • From the rear two belt boxes the belt has a ribbed detailed appearance.
ROTS41st thighs.jpg Thigh Armor
For 501st approval:
  • Armor is painted matte or satin white.
    • Approximately 1 inch from the top of the upper edge, a 1 inch grey stripe encircles the entire thigh.
  • Front of thigh armor has a flat triangular area near the knee.
    • From the top of the triangle, a ridge line travels up the front of the thigh to the top edge.
  • Rear of the thigh has an indention.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
For level two certification (if applicable):
  • Outside lower edge of the thigh comes to a point.
    • Inner lower edge is rounded.
ROTS41st knees.jpg Knee Armor
For 501st approval:
  • Realistic style knee armor.
  • Armor is panted matte or satin white.
  • Grey "V' -shape stripe follows the bottom edge of knee armor.
  • Knees have a protruding flat area in front oriented towards the top of Knee.
  • Knees bend around the front and connect to white detail clips that connect the strap on each side.
  • A white colored flat strap, about 2 inches wide, wraps around back of leg.
  • Grey areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Flat Strap has raised 5/8 Inch wide grey center strap.
ROTS41st shins.jpg Lower Leg Armor
For 501st approval:
  • Armor is painted primer grey.
  • Lower Legs are mirror images of each other.
  • The front of the armor has a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
  • Back of the lower legs have an indentation just under the calf that extends down to the ankle.
  • The outside of the calf is seamless.
    • A clam shell opening on the inner seam is acceptable.
  • Grey areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Armor is seamless with a trap door access through the indent in the rear of the lower leg.


Clone shoes copy.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle.
  • Boots are lace-less.
  • The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
  • There are no markings or labels from the shoe makers.
  • Boot soles are flat.
  • Boot soles are colored primer grey.


Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.

ROTS41st Backpack.jpg Radio Pack
For 501st approval:
  • The radio pack matches either the "slimline" or "full sized" version.
  • Radio is painted matte or satin black.
  • Radio consists of a horizontal top plate and vertical face plate.
  • Radio has an antenna mounted on top left.
  • There is a small curl knob near the antenna base.
  • Radio has a static bar on front face that bends back at two 90 degree angles to attach to side of the radio.
  • Radio has 3 knobs, dials, or lights on the bottom right corner.


41st Back02.jpg Radio Box Back Armor
For 501st approval:
  • Radio Box Back Armor is used as an alternate to the standard back armor.
    • Radio Pack is not used with this style back armor.
  • Armor is painted matte or satin white.
  • The previous one inch primer grey stripe continues from the side of the chest armor onto and back, curves upward, and ends at the rear under arm opening.
  • Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there are two parallel lines and the the right of the back there is a squared detail.
  • Top of the tank has a thermal detonator with three buttons.
  • in the recess under the back tank, there are two radio boxes.
  • Chest and back armor match together at the sides with no open gap.
    • A seam line is present.
  • Shoulder straps are placed underneath the chest to connect to the back.
For level two certification (if applicable):
  • Shoulder straps are slotted into the back armor, into the detail ridges of the top connection points.
  • Highly detailed resin insert should replace softer details.


DC15 carbine.jpg DC-15S Blaster
For 501st approval:

Manufactured by BlasTech Industries the DC-15S is smaller in scale than the DC-15A blaster rifle. Although it has a shorter range than that of the "A" model, it is easier to handle with a higher rate of fire. It features a folding stock for braced firing.

  • Realistic Clone Style DC-15S Blaster.
  • Blaster may be scratch built out of plastic, wood, metal or cast in resin.
  • Blaster has realistic Episode II or Episode III details:
    • Wire frame sight.
    • Folding stock.
    • (12) radiator fins evenly spaced along the length of barrel.
    • Igniter detail knobs.
    • Charge magazine clip on right side.
  • Total length is approximately 26“ (66 cm).
  • Because of the scale, the Hasbro version is incorrect.
For level two certification (if applicable):
  • Charge magazine detail on clip is metal to gun metal grey in color.
  • Detail bolts and screws are metal to gun metal grey in color.
  • Igniter knobs have some copper coloring.
  • Blaster is weathered.
For level three certification (if applicable):
  • Functioning Blue LED is installed in barrel.


DC15 rifle.jpg DC-15A Blaster Rifle
For 501st approval:

Manufactured by BlasTech Industries, the DC-15A is a tibanna gas, cartridge powered weapon. Hyper-ionized blue plasma bolts are more than capable of penetrating armored units. Exceptionally effective against both droids and contemporary targets.

  • Realistic Clone Style DC-15A Blaster Rifle.
  • Blaster rifle is scratch built out of plastic, wood, metal or cast in resin.
  • Blaster has realistic Episode II or Episode III details:
    • Flip up sight in down position.
    • (10) radiator fins evenly spaced along the length of barrel.
    • Power setting adjuster detail lever.
    • Sniper Scope attached under rifle in storage position.
    • Charge magazine clip on left side.
    • Igniter detail knobs.
  • Total length is approximately 55 inches (139.7 cm).
  • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • Charge magazine detail on clip is metal to gun metal grey in color.
  • Detail bolts and screws are metal to gun metal grey in color.
  • Igniter has some copper coloring.
  • Power setting adjuster detail lever is metal or gun metal grey.
  • Sniper scope is metal or gun metal grey.
  • Blaster is weathered.
For level three certification (if applicable):
  • Functioning Blue LED is installed in barrel.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.