Revision as of 19:12, 5 March 2013 by DTR1 (Talk | contribs)
crlblackhd.gif
Clone Commander Vill
Missingprofile.jpg
Model MODEL NAME, Photo by PHOTOGRAPHER NAME


Clone-Trooper-Detachment.png

Description: Clone Commander Vill
Prefix: CC
Detachment: Clone Trooper Detachment
Context: Star Wars: Dark Times (EU Comic series, multiple issues)
Commander Vill was a 501st Legion commander seen in the Dark Times comics and again in an action figure pack.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

  • This CRL is a work in progress.
  • As such, this costume must be approved by the Legion Membership Officer, via the appropriate section of the Legion forum.
  • If you have this costume and would like to assist with the completion of this library entry, please contact your detachment leader.
  • Please note that the use of the word "should" below does not indicate that the armor piece is considered open to interpretation. All instances of "should be" and "should have" will be replaced with "is" and "has", as this guide is completed.

Required Costume Components

The following costume components are present and appear as described below.

Blankwhite.gif Helmet
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}

Template:CRL-generic-clone-neckseal


TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


Blankwhite.gif Command Pauldron
For 501st approval:
  • Pauldron should be Episode III style.
    • The mantle over the left shoulder should be colored blue.
    • Right shoulder mantle and paneling on the remainder of the pauldron should be black.
    • On the right side of the Pauldron, a ammo belt is strung down to the belt.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Chest Ammo Belt
For 501st approval:
  • 3 white ammo boxes and one grey clip greeblie attached to a brown or white strap on right side of chest.
For level two certification (if applicable):
For level three certification (if applicable):


Blankwhite.gif Shoulders
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}
Blankwhite.gif Bicep
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}
Blankwhite.gif Elbow
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}
Blankwhite.gif Forearm
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}
Blankwhite.gif Handplates
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}


Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
  • Gloves cover any exposed skin.
  • Gloves do not show any labels or logos when the armor is worn.


Blankwhite.gif Chest
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}
Blankwhite.gif Back
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}
Blankwhite.gif Ab
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}
Blankwhite.gif Cod and Butt
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}
Blankwhite.gif Belt
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}
Blankwhite.gif Kama
For 501st approval:
  • Kama should be khaki or tea brown color, made from a heavy material like canvas or a tight weave burlap, and should be unlined and with no trim.
  • Length should be to the bottom of the knee armor.
  • The rear of the kama has a split at the bottom.
  • Should wrap around to the front belt boxes.
  • There are two straps from the kama that connect to a command buckle centered to the front of the belt.
For level two certification (if applicable):
For level three certification (if applicable):


Blankwhite.gif Commander Holsters
For 501st approval:
  • Holsters are hung from the belt, one on each side.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Thigh Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • There should be two blue diagonal stripes on the thighs.
    • The stripes start roughly midway up the inner thigh and angle upwards to a few inches from the top of the outer thigh.
  • Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
  • Rear of the thigh should have an indention.
  • Armor should be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):

For level three certification (if applicable):
  • Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.


Blankwhite.gif Knee Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Knees should wrap around the front of the leg. From top center a raised detail line should be present.
  • Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
For level two certification (if applicable):

For level three certification (if applicable):
  • Center strap should be primer gray.
  • Connection between the knee and the strapping should have a detail clip.


Blankwhite.gif Lower Leg Armor
For 501st approval:
  • Armor should be painted matte or satin white.
  • Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
  • Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
  • Calf can have an access area on the inside of the leg. The outside of the calf should be closed.
For level two certification (if applicable):

For level three certification (if applicable):
  • Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.
Blankwhite.gif Boots
For 501st approval:

For level two certification (if applicable):
{{{4}}}
For level three certification (if applicable):
{{{5}}}


Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.


CRL side arms.jpg DC-17 Hand Blaster
For 501st approval:

Manufactured by BlasTech Industries, DC-17 pistols are carried in quick-release holsters. They are widely recognized for their unusually high stopping power and firing rate.

  • The number of pistols carried is dependent on the amount of holsters.
  • This is the realistic variant of the DC-17 blaster.



DC15 carbine.jpg DC-15S Blaster
For 501st approval:

Manufactured by BlasTech Industries the DC-15S is smaller in scale than the DC-15A blaster rifle. Although it has a shorter range than that of the "A" model, it is easier to handle with a higher rate of fire. It features a folding stock for braced firing.

  • Blaster rifle may be scratch built out of plastic, wood, metal or cast in resin.
  • Total length should be approximately 26 “or 66 cm.
  • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • Folding stock (does not need to function).
  • A total of (12) radiator fins are present on the barrel.
  • Spare igniter is present on both sides of barrel.
  • Charge magazine is present on the right side.
For level three certification (if applicable):
  • Charge magazine is metal to gun metal grey in color.
  • Any bolts and screws are metal to gun metal grey in color.
  • Parts of the spare igniter are copper in color.
  • Blaster is weathered.


DC15 rifle.jpg DC-15A Blaster Rifle
For 501st approval:

Manufactured by BlasTech Industries, the DC-15A is a tibanna gas, cartridge powered weapon. Hyper-ionized blue plasma bolts are more than capable of penetrating armored units. Exceptionally effective against both droids and contemporary targets.

  • Blaster rifle is scratch built out of plastic, wood, metal or cast in resin.
  • Total length is approximately 55 inches (139.7 cm).
    • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • A total of (10) radiator fins are present on the barrel.
  • A power setting adjuster is present.
  • The correct style of sniper scope is present.
  • Charge magazine lock is present on the left side.
  • Power setting adjuster, sniper scope and charge magazine lock is metal to gun metal gray in color.
For level three certification (if applicable):
  • Sniper scope is able to be removed from storage position (bottom of rifle) and attached to the top of the rifle.
  • Parts of the spare igniter are copper in color.
  • Front optical sight is able to flip to the up position.
  • Any bolts and screws are metal to gun metal grey in color.
  • Blaster is weathered.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:CC_CommanderVill

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.