Revision as of 02:12, 28 March 2014 by TK826 (Talk | contribs)
crlblackhd.gif
Clone Commander Wolffe (Season 2)
Missingprofile.jpg
Model MODEL NAME, Photo by PHOTOGRAPHER NAME


Clone-Trooper-Detachment.png

Description: Clone Commander Wolffe (Season 2)
Prefix: CC
Detachment: Clone Trooper Detachment
Context: The Clone Wars, seasons 1-3

Commander Wolffe is the leader of the 104th Battalion's Wolfpack Squad. Talented in military strategy and leadership skills, Wolffe favors service on the front lines over more tedious assignments, such as supply missions or support duties.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

  • This CRL is a work in progress.
  • As such, this costume must be approved by the Legion Membership Officer, via the appropriate section of the Legion forum.
  • If you have this costume and would like to assist with the completion of this library entry, please contact your detachment leader.
  • Please note that the use of the word "should" below does not indicate that the armor piece is considered open to interpretation. All instances of "should be" and "should have" will be replaced with "is" and "has", as this guide is completed.

Blankwhite.gif Helmet
For 501st approval:
  • Phase 1 style helmet.
  • Helmet painted with a base of matte or satin white.
  • On the front center of the dome is a downward facing red triangle.
  • Wrapping around and covering much of the front and sides of the helmet is a large, painted matte blue-grey, wolf head motif.
  • A rangefinder stalk is mounted on the helmet's right side earpiece which includes a white colored topper.
  • The bottom ridge of the helmet, below each ear piece, has 4 slotted vents.
  • The rear indented helmet band and large rear indented section of the helmet is painted blue-grey.
  • The rear center disc is painted matte or satin white.
  • Weathering of blue-grey areas consists of various scuff marks and patches of color fading.
  • Weathering of the white areas are shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):


TC animated neckseal.jpg Neck Seal
For 501st approval:
  • Neck seal is black in color with no ribbing.
  • No logos or labels are visible.
    • If the seal is not incorporated as part of the under suit, a balaclava or other similar covering is acceptable.
For level two certification (if applicable):
  • Neck seal closes in the front via 2 small black snaps.


TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


S4 wolffe bells.jpg Shoulder Bells
For 501st approval:
  • The left shoulder bell is painted matte blue-gray with white tribal motif
  • Left shoulder also includes a mounted antenna array.
  • Right shoulder bell painted matte blue-gray with a white wolf head emblem.
  • Weathering of blue-grey areas consists of various scuff marks and patches of color fading.
  • Weathering of the white areas are shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
S4 wolffe biceps.jpg Upper Arm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • The outside of each bicep is painted with a blue-gray, inverted 4 point design.
  • The back of each bicep has a cut-out area to fit the elbow armor.
  • Biceps should be seamless.
  • Weathering of blue-grey areas consists of various scuff marks and patches of color fading.
  • Weathering of the white areas are shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Forearm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Much of the lower forearm pieces are painted with Blue-gray markings consisting of pointed peaks of varying heights.
  • Left forearm has a compad with 4 square recessed areas and 1 slightly smaller square recessed area.
    • The smaller recess is closest to the elbow.
  • Armor is seamless on the outside edge.
    • Due to the shape of the armor, a butted seam is acceptable on the inside if required.
  • Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
  • Weathering of blue-grey areas consists of various scuff marks and patches of color fading.
  • Weathering of the white areas are shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Hand Plates
For 501st approval:
  • Armor is painted matte or satin blue-gray.
  • Weathering of blue-grey areas consists of various scuff marks and patches of color fading.
For level two certification (if applicable):
For level three certification (if applicable):


Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
  • Gloves cover any exposed skin.
  • Gloves do not show any labels or logos when the armor is worn.


Blankwhite.gif Chest Armor
For 501st approval:
  • Armo ris painted matte or satin white.
  • Upper chest and shoulder areas is painted with an arched blue-grey section.
  • Lower portion of the chest has a curved area to match the abdomen armor.
  • Chest and back plate join together at the sides and shoulders with no open gap.
    • There is a butted seam line between the front and back armor pieces.
  • Shoulder straps are placed over the chest and back armor at the seams.
  • Shoulder straps are painted blue-grey.
  • Weathering of blue-grey areas consists of various scuff marks and patches of color fading.
  • Weathering of the white areas are shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Back Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Top half of the back armor is painted blue-gray.
    • The bottom edge of this blue-gray section angles inward/ downward, from the mid arm opening, to the lower edge (and across) the rear detail box.
  • The faceplate of the back armor box contains "O 11" details, similar to a standard Stormtrooper
  • Chest and back plate join together at the sides and shoulders with no open gap.
    • There is a butted seam line between the front and back armor pieces.
  • Shoulder straps are placed over the chest and back armor at the seams.
  • Shoulder straps are painted blue-grey.
  • Weathering of blue-grey areas consists of various scuff marks and patches of color fading.
  • Weathering of the white areas are shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):


TC animated ab.jpg Abdomen Armor
For 501st approval:
  • Animated Phase I Abdomen Armor.
  • Armor is painted matte or satin white.
  • Top edge of the armor is curved to match the chest.
  • Abdomen armor protrudes out in the middle to match the shape of the chest.
  • (4) inset lines divide the abdomen armor into segments.
  • Abdomen and Kidney armor connect at the sides with no open gap.
    • A butted seam between abdomen and kidney armor is acceptable.
  • Armor is weathered with shades of grey.



TC animated grunt kidney.jpg Kidney Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Kidney and abdomen armor connect at the sides with no open gap.
    • A butted seam between the kidney and abdomen armor is acceptable.
  • Armor is weathered with shades of grey.



TC animated cod.jpg Codpiece and Belt front
For 501st approval:
  • Armor is painted matte or satin white.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • The front segments have a key/slot detail.
  • Belt boxes are mounted at the hips.
  • Codpiece and Posterior armor connect at the hips.
    • Butted seams are permitted at this connection if required.
  • Armor is weathered with shades of grey.



TC animated butt.jpg Posterior Armor, Belt rear and Detonator
For 501st approval:
  • Armor is painted matte or satin white.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • Posterior armor and Codpiece connect at the hips.
    • Butted seams are permitted at this connection if required.
  • Detonator is centered on the back of belt.
    • Detonator has no control buttons.
    • The detonator has (2) lines set in approx 1/2" - 5/8" from the edges.
      • Lines may be recessed or painted on
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Detonator lines are recessed.


TC animated belt box.jpg Belt Boxes
For 501st approval:
  • Two rectangular boxes with one mounted on each side of belt.
  • Boxes are painted matte or satin white.
    • The top side of the box is tapered outward.
    • There is an inset detail near the top of each box.
  • Armor is weathered with shades of grey.



TC animated thighs.jpg Thigh Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Front of thigh armor has a flat triangular area near the knee with a notch cut out for the knee armor.
  • From the top of the triangle a ridge line travels up the front of the thigh to the top edge.
  • The upper outer edge has an angled section.
  • The armor is weathered with shades of grey.
For level two certification (if applicable):
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
Blankwhite.gif Kama
For 501st approval:
  • The kama is made of a heavy black material, or heavy canvas.
  • The kama has blue-grey trim that should match the other accented armor pieces.
  • The front edges of the kama should line up with the outside edges of the front two panels of the belt.
  • The bottom front corners of the kama are rounded angles.
  • The rear of the kama is slightly longer than the front.
  • The sides of the kama extend to top of the knee armor.
  • The back of the kama is split all the way up to the belt.
  • Weathering consists of lightly colored grey scuff marks.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Holsters
For 501st approval:
  • Holsters should be painted matte or satin white.
  • Holsters connect to the belt via black colored straps.
  • Weathering of the white areas are shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Shin Armor
For 501st approval:
  • Armor is painted with a base of matte or satin white.
  • Much of the lower shins are painted with a blue-gray, jagged peak design of varying heights.
    • The center peak extends to the top edge of the knee section.
  • Knee armor is integrated with the lower leg.
  • The armor has a flat center triangle area, below the knee plate, with the single point facing downward.
  • Outer seam of the shin must be seamless.
    • Due to the shape of the armor, a butted seam is permitted on the inside or back of the shin.
  • Weathering of blue-grey areas consists of various scuff marks and patches of color fading.
  • Weathering of the white areas are shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Boots
For 501st approval:
  • The shoes are blue-gray in color, matching the other accented armor pieces.
  • A detail strap is attached over the top of each boot.
  • The ends of each strap have flat discs on either side of the foot.
  • The boots have flat soles with a notched tread.
For level two certification (if applicable):
For level three certification (if applicable):
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.


CW animated dc17 pistol.jpg DC-17 Hand Blaster (animated style)
For 501st approval:

Manufactured by BlasTech Industries, DC-17 pistols are designed for use as secondary weapons. Because they are widely recognized for their high stopping power and firing rate, many battlefield officers use them as primarily combat weapons.

  • This is the animated variant of the DC-17 blaster.
  • The number of pistols carried is dependent on the amount of holsters.



CRLdc15s-animated.jpg DC-15S Blaster Carbine (animated style)
For 501st approval:

Manufactured by BlasTech Industries, this weapon is commonly carried by the Troopers of the Galactic Republic.

  • This is the animated variant of the DC-15S blaster rifle.


This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:CC_CW-animated_wolffe_s02

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.