(Difference between revisions)
(6 intermediate revisions not shown)
Line 1: Line 1:
-
{{CRLheader|Clone Commander Stone|COSTUME IMAGE|MODEL NAME|PHOTOGRAPHER NAME}}
+
{{CRLheader|Commander Stone|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}
-
{{CRLdetinfo| 1111 |Clone Commander Stone|CC|The Clone Wars, season 1|Stone was a clone trooper commander in the Coruscant Guard. He appears in Season 1, Episode 12 "The Gungan General".
+
{{CRLdetinfo|1111|Commander Stone|CC|The Clone Wars: Season 1 - Episode 12|
-
}}
+
-
{{CRLwipapproval}}
+
Stone is a Commander in the Grand Army of the Republic's "Coruscant Guard", often serving to lead the Diplomatic Escort Group. Although his position in the Guard is a prestigious one, he finds it frustrating when considering that he is trained for war and must instead take orders from Gungan politicians. Despite his skepticism, Stone is well disciplined and carries out orders, regardless of their origin.}}
 +
 
 +
{{CRLctnlevels}}
 +
 
 +
{{CRLwiplmoapproval}}
 +
 
 +
{{CRLrequirements}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Helmet|
 +
*Phase 1 style helmet.
 +
*Helmet is painted with a base of matte or satin white.
 +
*The top fin of the helmet is painted a maroon red color.
 +
*The top and front center of the dome is painted with a the same maroon red color.
 +
**This red area does not extend to the lower rear of the dome. It instead curves around the backside of the top fin in an arched pattern.
 +
*Wrapped around the red area is a wide white stripe.
 +
**This stripe starts above the eye lens, about 1/3 from the outside edge, and again curves around the backside of the dome, returning to the same spot on the opposite side of the helmet.
 +
**The white stripe starts out wide as it leaves the eye lens, but grows thinner as it wraps around the backside of the dome.
 +
*The front center of the helmet, including the face, the chin, and eye lens surround is painted white.
 +
**Excluding the eye lens area (which is all white), this white color only extends from mid-cheek, around the front, to the other mid-cheek.
 +
*The sides and rear of the helmet is painted the smae maroon red color as the other markings.
 +
*The indented rear helmet band, including the large rear indented section, is painted a deeper/ darker red than any of the other areas.
 +
*The raised center disk, at the rear of the helmet, is painted matte or satin white to match the other white areas.
 +
*4 rectangular vents holes are located on each side, at the base of the ear pieces.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRL-TC_animated_neckseal}}
 +
 
 +
{{CRL-generic-undersuit}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|
 +
*Armor is painted with a base of matte or satin white.
 +
*Each shoulder is adorned with a stylized version of the symbol of the Galactic Senate.
 +
**These symbols are painted the same red color as the other armor details.
 +
**The left, right and upper extended lines of the symbol extend all the way to the edges of the shoulder piece.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Upper Arm Armor|
 +
*Armor is painted matte or satin white.
 +
*Each bicep has a maroon red stripe painted down the outside.
 +
*Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
 +
*Armor is seamless. No visible traces of how the armor was assembled should be shown.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Forearm Armor|
 +
*Armor is painted matte or satin white.
 +
*Each armor piece has a maroon red stripe painted along the length of the forearm, from the bottom edge of the elbow section to the wrist.
 +
*Left forearm has a compad with 4 square recessed areas and 1 slightly smaller square recessed area.
 +
**The smaller recess is closest to the elbow.
 +
**Although the compad is centered on the red forearm stripe, the entire compad itself remains white.
 +
*Armor is seamless on the outside edge.
 +
**Due to the shape of the armor, a butted seam is acceptable on the inside if required. 
 +
*Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
 +
**Elbow section is painted matte or satin white with no red markings.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Hand Plates|
 +
*Armor is painted matte or satin white.
 +
*Hand plates are mirror images of each other. 
 +
*Hand plates have a top curving ridge that comes to a point over the index or middle finger, just past the main knuckle of the hand.
 +
*The left and right side of each hand plate is painted with the maroon red color.
 +
**The middle of each hand plates remains white.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRL-generic_black_gloves}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Chest Armor|
 +
*Armor is painted matte or satin white.
 +
*Chest armor has maroon red markings which form a box type design.
 +
*These markings start as downward facing hook shapes near the upper center of the chest, then "dog-leg" around the collar area to cover the entire upper section on each side of the collar.
 +
**The collar ring itself remains white.
 +
*After covering the upper shoulder area, the design then falls back down each side of the chest, covering large areas of the left and right sides.
 +
**This red color/ design continues around the top and sides of the body, covering the entire side sections and much of the back armor.
 +
**See "Back Armor" section for details. 
 +
*Lower portion of the chest has a curved notch for the abdomen armor to fit into.
 +
*Chest and back plate match together at the sides and shoulders with no open gap.
 +
**Butted seam lines are permitted if required.
 +
*Shoulder straps are placed over the chest and back armor at the seams.
 +
**Shoulder straps are the same red color.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Back Armor|
 +
*Armor is painted with a base of matte or satin white.
 +
*The previously described front chest markings transition into large maroon areas which cover the entire sides of the body as well as the sides and top of the back armor.
 +
*This large maroon area covers nearly all of the back armor with a few  exceptions.
 +
**The collar ring, the rear detail box (including all 4 sides) and an equally wide area, from the bottom of the box to the bottom of the armor piece all remain white. 
 +
*Chest and back plate match together at the sides and shoulders with no open gap.
 +
**Butted seam lines are permitted if required.
 +
*Shoulder straps are placed over the chest and back armor at the seams.
 +
**Shoulder straps are the same red color.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRL-TC_animated_ab}}
 +
 
 +
{{CRL-TC_animated_kidney}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Codpiece and Belt Front|
 +
*The cod armor is painted matte or satin white.
 +
*The belt is painted the maroon red color.
 +
*Belt is approx 3" tall and divided into 1.75" wide segments.
 +
*Cod and Posterior armor should connect at the hips.
 +
**Butted seams are permitted at this connection if required.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Posterior Armor, Belt Rear and Detonator|
 +
*Posterior armor is painted matte or satin white.
 +
*The belt is painted the maroon red color.
 +
*Belt is approx 3" tall and divided into 1.75" wide segments.
 +
*Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.
 +
*Detonator is centered on the back of belt with no control buttons.
 +
**Detonator is painted the same maroon red color as the other detail pieces.
 +
**The detonator has 2 lines set in approx 1/2" - 5/8" from the edges.
 +
**Lines may be recessed or painted on.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.|
 +
*Detonator lines must be recessed.|}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Belt Boxes|
 +
*Two rectangular boxes are mounted at each hips.
 +
**The top edge of the box is tapered down toward the outside.
 +
**There is an inset detail near the top of each box.
 +
*Boxes are painted the maroon red color.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.||}}
 +
 
 +
{{CRLtemplate|File:Animated Holsters.jpg|Holsters|
 +
*Holsters are painted satin or matte white.
 +
*Holsters connect to the belt via matte or satin white straps.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Thigh Armor|
 +
*The majority of the thigh armor is painted maroon red.
 +
*The remaining white area consists of a wide stripe that begins just above the knee, travels up to the top of the piece and turns outward before dropping back down again. This continued stripe does not again reach the bottom edge of the armor piece, but instead stops short and turns outward once again to continue its travel around the leg. The stripe finally dead-ends at the center of the inner lower thigh.
 +
*The front lower area of the armor has a cut out section to fit the shape of the knee armor.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRLtemplate|File:Blankwhite.gif|Lower Leg Armor|
 +
*Armour is painted with a base of matte or satin white.
 +
*Knee armor is integrated with the lower leg.
 +
**The knee section is painted white with no red markings.
 +
*The armor has a flat, downward facing, triangle area below the knee plate. This triangle area then transitions into a hard ridge line down the front of the shin.
 +
*Red markings consist of a stripe around the ankle which then travels up the front of the leg before splitting into a Y shape to wrap around the triangle area. This red stripe then continues around the back of the upper calf to form one continuous line.
 +
*The red sections are weathered with heavy scuff marks and patchy color faded areas.
 +
*White areas are weathered with shades of grey.||}}
 +
 
 +
{{CRL-TC_animated_boots}}
 +
 
 +
{{CRLaccessories}}
 +
 
 +
{{CRLdc17pistol-animated}}
 +
 
 +
{{CRLdc15s-animated}}
 +
 
 +
{{CRLfooter|CTN_CRL|C}}

Revision as of 17:26, 22 March 2014

crlblackhd.gif
Commander Stone
Missingprofile.jpg
Model MODEL NAME, Photo by PHOTOGRAPHER NAME


Clone-Trooper-Detachment.png

Description: Commander Stone
Prefix: CC
Detachment: Clone Trooper Detachment
Context: The Clone Wars: Season 1 - Episode 12

Stone is a Commander in the Grand Army of the Republic's "Coruscant Guard", often serving to lead the Diplomatic Escort Group. Although his position in the Guard is a prestigious one, he finds it frustrating when considering that he is trained for war and must instead take orders from Gungan politicians. Despite his skepticism, Stone is well disciplined and carries out orders, regardless of their origin.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

  • This CRL is a work in progress.
  • As such, this costume must be approved by the Legion Membership Officer, via the appropriate section of the Legion forum.
  • If you have this costume and would like to assist with the completion of this library entry, please contact your detachment leader.
  • Please note that the use of the word "should" below does not indicate that the armor piece is considered open to interpretation. All instances of "should be" and "should have" will be replaced with "is" and "has", as this guide is completed.

Required Costume Components

The following costume components are present and appear as described below.

Blankwhite.gif Helmet
For 501st approval:
  • Phase 1 style helmet.
  • Helmet is painted with a base of matte or satin white.
  • The top fin of the helmet is painted a maroon red color.
  • The top and front center of the dome is painted with a the same maroon red color.
    • This red area does not extend to the lower rear of the dome. It instead curves around the backside of the top fin in an arched pattern.
  • Wrapped around the red area is a wide white stripe.
    • This stripe starts above the eye lens, about 1/3 from the outside edge, and again curves around the backside of the dome, returning to the same spot on the opposite side of the helmet.
    • The white stripe starts out wide as it leaves the eye lens, but grows thinner as it wraps around the backside of the dome.
  • The front center of the helmet, including the face, the chin, and eye lens surround is painted white.
    • Excluding the eye lens area (which is all white), this white color only extends from mid-cheek, around the front, to the other mid-cheek.
  • The sides and rear of the helmet is painted the smae maroon red color as the other markings.
  • The indented rear helmet band, including the large rear indented section, is painted a deeper/ darker red than any of the other areas.
  • The raised center disk, at the rear of the helmet, is painted matte or satin white to match the other white areas.
  • 4 rectangular vents holes are located on each side, at the base of the ear pieces.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):


TC animated neckseal.jpg Neck Seal
For 501st approval:
  • Neck seal is black in color with no ribbing.
  • No logos or labels are visible.
    • If the seal is not incorporated as part of the under suit, a balaclava or other similar covering is acceptable.
For level two certification (if applicable):
  • Neck seal closes in the front via (2) small black snaps.


TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


Blankwhite.gif Shoulder Bells
For 501st approval:
  • Armor is painted with a base of matte or satin white.
  • Each shoulder is adorned with a stylized version of the symbol of the Galactic Senate.
    • These symbols are painted the same red color as the other armor details.
    • The left, right and upper extended lines of the symbol extend all the way to the edges of the shoulder piece.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Upper Arm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Each bicep has a maroon red stripe painted down the outside.
  • Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
  • Armor is seamless. No visible traces of how the armor was assembled should be shown.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Forearm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Each armor piece has a maroon red stripe painted along the length of the forearm, from the bottom edge of the elbow section to the wrist.
  • Left forearm has a compad with 4 square recessed areas and 1 slightly smaller square recessed area.
    • The smaller recess is closest to the elbow.
    • Although the compad is centered on the red forearm stripe, the entire compad itself remains white.
  • Armor is seamless on the outside edge.
    • Due to the shape of the armor, a butted seam is acceptable on the inside if required.
  • Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
    • Elbow section is painted matte or satin white with no red markings.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Hand Plates
For 501st approval:
  • Armor is painted matte or satin white.
  • Hand plates are mirror images of each other.
  • Hand plates have a top curving ridge that comes to a point over the index or middle finger, just past the main knuckle of the hand.
  • The left and right side of each hand plate is painted with the maroon red color.
    • The middle of each hand plates remains white.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):


Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
  • Gloves cover any exposed skin.
  • Gloves do not show any labels or logos when the armor is worn.


Blankwhite.gif Chest Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Chest armor has maroon red markings which form a box type design.
  • These markings start as downward facing hook shapes near the upper center of the chest, then "dog-leg" around the collar area to cover the entire upper section on each side of the collar.
    • The collar ring itself remains white.
  • After covering the upper shoulder area, the design then falls back down each side of the chest, covering large areas of the left and right sides.
    • This red color/ design continues around the top and sides of the body, covering the entire side sections and much of the back armor.
    • See "Back Armor" section for details.
  • Lower portion of the chest has a curved notch for the abdomen armor to fit into.
  • Chest and back plate match together at the sides and shoulders with no open gap.
    • Butted seam lines are permitted if required.
  • Shoulder straps are placed over the chest and back armor at the seams.
    • Shoulder straps are the same red color.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Back Armor
For 501st approval:
  • Armor is painted with a base of matte or satin white.
  • The previously described front chest markings transition into large maroon areas which cover the entire sides of the body as well as the sides and top of the back armor.
  • This large maroon area covers nearly all of the back armor with a few exceptions.
    • The collar ring, the rear detail box (including all 4 sides) and an equally wide area, from the bottom of the box to the bottom of the armor piece all remain white.
  • Chest and back plate match together at the sides and shoulders with no open gap.
    • Butted seam lines are permitted if required.
  • Shoulder straps are placed over the chest and back armor at the seams.
    • Shoulder straps are the same red color.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):


TC animated ab.jpg Abdomen Armor
For 501st approval:
  • Animated Phase I Abdomen Armor.
  • Armor is painted matte or satin white.
  • Top edge of the armor is curved to match the chest.
  • Abdomen armor protrudes out in the middle to match the shape of the chest.
  • (4) inset lines divide the abdomen armor into segments.
  • Abdomen and Kidney armor connect at the sides with no open gap.
    • A butted seam between abdomen and kidney armor is acceptable.
  • Armor is weathered with shades of grey.



TC animated grunt kidney.jpg Kidney Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Kidney and abdomen armor connect at the sides with no open gap.
    • A butted seam between the kidney and abdomen armor is acceptable.
  • Armor is weathered with shades of grey.


Blankwhite.gif Codpiece and Belt Front
For 501st approval:
  • The cod armor is painted matte or satin white.
  • The belt is painted the maroon red color.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • Cod and Posterior armor should connect at the hips.
    • Butted seams are permitted at this connection if required.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Posterior Armor, Belt Rear and Detonator
For 501st approval:
  • Posterior armor is painted matte or satin white.
  • The belt is painted the maroon red color.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.
  • Detonator is centered on the back of belt with no control buttons.
    • Detonator is painted the same maroon red color as the other detail pieces.
    • The detonator has 2 lines set in approx 1/2" - 5/8" from the edges.
    • Lines may be recessed or painted on.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
  • Detonator lines must be recessed.
For level three certification (if applicable):
Blankwhite.gif Belt Boxes
For 501st approval:
  • Two rectangular boxes are mounted at each hips.
    • The top edge of the box is tapered down toward the outside.
    • There is an inset detail near the top of each box.
  • Boxes are painted the maroon red color.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
For level two certification (if applicable):
For level three certification (if applicable):
150px Holsters
For 501st approval:
  • Holsters are painted satin or matte white.
  • Holsters connect to the belt via matte or satin white straps.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Thigh Armor
For 501st approval:
  • The majority of the thigh armor is painted maroon red.
  • The remaining white area consists of a wide stripe that begins just above the knee, travels up to the top of the piece and turns outward before dropping back down again. This continued stripe does not again reach the bottom edge of the armor piece, but instead stops short and turns outward once again to continue its travel around the leg. The stripe finally dead-ends at the center of the inner lower thigh.
  • The front lower area of the armor has a cut out section to fit the shape of the knee armor.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Lower Leg Armor
For 501st approval:
  • Armour is painted with a base of matte or satin white.
  • Knee armor is integrated with the lower leg.
    • The knee section is painted white with no red markings.
  • The armor has a flat, downward facing, triangle area below the knee plate. This triangle area then transitions into a hard ridge line down the front of the shin.
  • Red markings consist of a stripe around the ankle which then travels up the front of the leg before splitting into a Y shape to wrap around the triangle area. This red stripe then continues around the back of the upper calf to form one continuous line.
  • The red sections are weathered with heavy scuff marks and patchy color faded areas.
  • White areas are weathered with shades of grey.
For level two certification (if applicable):
For level three certification (if applicable):


TC animated boots.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area.
  • Boots are lace-less and have flat soles.
  • Boots have a center strip running from the toe to the ankle.
  • A strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap.
For level two certification (if applicable):
  • Boots have accurate notched sole.
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.


CW animated dc17 pistol.jpg DC-17 Hand Blaster (animated style)
For 501st approval:

Manufactured by BlasTech Industries, DC-17 pistols are designed for use as secondary weapons. Because they are widely recognized for their high stopping power and firing rate, many battlefield officers use them as primarily combat weapons.

  • This is the animated variant of the DC-17 blaster.
  • The number of pistols carried is dependent on the amount of holsters.



CRLdc15s-animated.jpg DC-15S Blaster Carbine (animated style)
For 501st approval:

Manufactured by BlasTech Industries, this weapon is commonly carried by the Troopers of the Galactic Republic.

  • This is the animated variant of the DC-15S blaster rifle.


This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:CC_CW-animated_stone

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.