(Difference between revisions)
Line 29: Line 29:
{{CRL-generic-undersuit}}
{{CRL-generic-undersuit}}
-
{{CRLtemplate|File:Blankwhite.gif|Mantle|||}}
+
{{CRLtemplate|File:CC_animated_rex_mantle.jpg|Mantle|||}}
{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|||}}
{{CRLtemplate|File:Blankwhite.gif|Shoulder Bells|||}}

Revision as of 22:06, 9 June 2011

crlblackhd.gif
Clone Captain Rex (Phase 1)
CC-Rex animated full.jpg
Model Phil Fraboni, CC-3714, Photo by Dave Mydlo


Clone-Trooper-Detachment.png

Description: Clone Captain Rex (Phase 1)
Prefix: CC
Detachment: Clone Trooper Detachment
Context: The Clone Wars, seasons 1-3
Rex leads the 501st Legion, and has appeared in multiple episodes.


This CRL is a work in progress and is not yet ready to use for GML approval!


CC animated rex helmet front.jpg Helmet
For 501st approval:
  • Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
  • Helmet should be painted matte or satin white.If weathered, the weathering should be shades of grey.
  • Black visor extends down through the entire frown area.
  • Narrow fin on dome.
  • Raised bump at each ear, 1" - 1.25" in diameter.
  • Antenna with range finder on right ear cap. Boba Fett style RF topper not acceptable.
  • 4 Vents on each side of helmet. May be painted black or grey, or cut out and filled with black mesh.
  • All of the following paint details on the helmet are rough edged / appear hand painted.
    • Blue outline around visor, extending down to mouth indent.
    • Blue "Jaig eyes" on forehead. Eyes are not symmetrical.
    • Blue triangles between Jaig eyes
    • 4 yellow "kill stripes" at either temple. Stripes may be soft edged / appear hand painted.
  • Blue stripe around back of dome.
  • White circle and rectangular indent at the back of the helmet.
For level two certification (if applicable):
  • Helmet must be weathered.
For level three certification (if applicable):


TC animated neckseal.jpg Neck Seal
For 501st approval:
  • Neck seal to be black in color with no ribbing.
  • No logos or labels are to be visible.
  • If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.
For level two certification (if applicable):
  • Neck seal should close via 2 small black snaps in the front.
For level three certification (if applicable):


TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


CC animated rex mantle.jpg Mantle
For 501st approval:

For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Shoulder Bells
For 501st approval:

For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Biceps
For 501st approval:

For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Forearms
For 501st approval:

For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Hand Plates
For 501st approval:

For level two certification (if applicable):
For level three certification (if applicable):


Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin.
For level two certification (if applicable):
For level three certification (if applicable):


TC animated chest.jpg Chest Armor
For 501st approval:
  • Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
  • Lower portion of the chest has a curved notch for the abdomen armor to fit into.
  • Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
  • Shoulder straps must be placed over the chest and back armor at the seams.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):


TC animated back.jpg Back Armor
For 501st approval:
  • Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
  • Rear tank has detailed area that contains a O11 pattern similar to a stormtrooper.
  • Shoulder straps should be placed over the chest and back armor at the seams.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):


TC animated ab.jpg Ab Armor
For 501st approval:
  • Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
  • Top edge of the armor is curved to match the chest.
  • The ab armor protrudes out in the middle to better up with the chest.
  • 4 inset lines divide the ab plate into segments.
  • A butted seam between ab plate and kidney is acceptable.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):


TC animated grunt kidney.jpg Kidney Armor
For 501st approval:
  • Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
  • A butted seam between ab plate and kidney is acceptable.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):


TC animated cod.jpg Codpiece and belt front
For 501st approval:
  • Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
  • Belt is approx 3" tall and divided into 1.75" wide segments. The front segments have a key/slot detail.
  • Belt boxes are mounted at the hips. Butted seams are permitted at this connection if required.
  • Cod and Posterior armor should connect at the hips.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):


TC animated butt.jpg Posterior Armor, belt rear and detonator
For 501st approval:
  • Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.
  • Detonator is centered on the back of belt with no control buttons. The detonator has 2 lines set in approx 1/2" - 5/8" from the edges. Lines may be recessed or painted on
For level two certification (if applicable):
  • Armor must be weathered.
  • Detonator lines must be recessed.
For level three certification (if applicable):


TC animated belt box.jpg Belt Boxes
For 501st approval:
  • Two rectangular boxes are mounted at the hips.
  • Boxes are painted matte or satin white.
    • The top side of the box is tapered outward.
    • There is an inset detail near the top of each box.
  • If weathered, the weathering should be shades of grey.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):


TC animated thighs.jpg Thigh Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
  • The armor piece is weathered with shades of grey.
For level two certification (if applicable):
  • Armor is seamless.
    • No visible traces of how the armor was assembled should be shown.
For level three certification (if applicable):
Blankwhite.gif Kama
For 501st approval:

For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Holsters
For 501st approval:

For level two certification (if applicable):
For level three certification (if applicable):
Blankwhite.gif Shins
For 501st approval:

For level two certification (if applicable):
For level three certification (if applicable):


TC animated boots.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles.
  • Boots have a center strip running from the toe to the ankle, a strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap.
For level two certification (if applicable):
  • Boots must have accurate notched sole.
For level three certification (if applicable):
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.


CW animated dc17 pistol.jpg DC-17 Hand Blaster (animated style)
For 501st approval:
  • This is the animated variant of the DC-17 blaster. Manufactured by BlasTech Industries, DC-17 pistols are designed for use as secondary weapons. Because they are widely recognized for their high stopping power and firing rate, many battlefield officers use them as primarily combat weapons.



CRLdc15s-animated.jpg DC-15S Blaster Carbine (animated style)
For 501st approval:

This is the animated variant of the DC-15S blaster rifle. Manufactured by BlasTech Industries, this weapon is commonly carried by the Troopers of the Galactic Republic.



Blankwhite.gif DC-15A Blaster Rifle (animated style)
For 501st approval:

This is the animated variant of the DC-15A blaster rifle. Manufactured by BlasTech Industries, this blaster is the standard issue weapon carried by the Clone Troopers of the Grand Army of the Republic.


Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.