(Difference between revisions)
Line 38: Line 38:
{{CRLtemplate-nolevels|File:Fox_Shoulders_Phase2.jpg|Shoulder Armor|
{{CRLtemplate-nolevels|File:Fox_Shoulders_Phase2.jpg|Shoulder Armor|
*Shoulders are painted satin or matte white.
*Shoulders are painted satin or matte white.
-
*The left shoulder has the emblem of the galactic senate painted on it in crimson.
+
*The left shoulder has the emblem of the galactic senate painted in crimson.
-
*Shoulders are a mirror image of each other in shape.
+
*Shoulders are tear drop in shape with all rounded edges.
-
*Shoulders taper at the center toward the bottom edge.
+
*Shoulder armor is not symmetrical.
 +
**The shoulders slightly curve back at the bottom.
*Armor is weathered with shades of grey.||}}
*Armor is weathered with shades of grey.||}}

Revision as of 11:03, 19 June 2014

crlblackhd.gif
Commander Fox (Phase 2)
Fox full 2.jpg
Model CC 69696, Photo by Timothy Lee


Clone-Trooper-Detachment.png

Description: Commander Fox (Phase 2)
Prefix: CC
Detachment: Clone Trooper Detachment
Context: The Clone Wars Season 4

Commander Fox appears in the "Deception" episode of Season 4. He is the commander that accepts Hardeen into custody. While never named in the episode, it has been confirmed that it is Fox. Commander Fox appears again in The Clone Wars Season 5 episode "The Jedi Who Knew Too Much" as the head of the Republic detention facility.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
  • Any uncertainties or questionable aspects of the submitted costume should be brought to the appropriate DL/GML peer review section of the legion forum.
Required Costume Components

The following costume components are present and appear as described below.

Fox s4 helmet.jpg Helmet
For 501st approval:
  • Phase 2 Clone Wars style helmet required. Movie style helmets cannot be combined with animated armor.
  • Low fin with a narrow ridge along each side.
  • Grey frown with 3 black teeth either side. Teeth may be cut out and backed with black mesh or painted.
  • T shaped visor that extend down to the nose.
  • 2 aerators in the front, Aerators are black with a grey detail in the centre.
  • Each cheek tube has 6 black stripes.
  • 3 dark grey raised bumps on each ear.
  • Chin greeblie is painted black or dark grey.
  • Helmet is painted crimson.
  • Helmet fin is painted satin or matte white.
  • Centre lower jaw is painted satin or matte white, weathered crimson paint shows underneath the white.
  • There are 12 white stripes on the front of each tube, they are evenly spaced starting at the 12 O’clock position and finishing at the 5 o’clock position for the left and 7 o’clock position for the right.
  • The cheeks are painted satin or matte white and the white extends around the ear and to the rear recessed areas, finishing at the rear raised section.
  • There is an antenna behind the right ear, the base starts at the recessed area and finishes approximately at the top of the ear cap. The antenna then extends from the base.
  • Antenna is painted dark grey or black.
  • Bullet shape lamp with white lense on the left hand side of the dome sits just above the visor. Painted dark grey/black.
  • A phase 2 animated visor sits on the brow and extends to the back of each ear.
  • Visor is painted dark grey or black with grey details.
  • Armor is weathered with shades of grey.



TC animated neckseal.jpg Neck Seal
For 501st approval:
  • Neck seal is black in color with no ribbing.
  • No logos or labels are visible.
    • If the seal is not incorporated as part of the under suit, a balaclava or other similar covering is acceptable.
For level two certification (if applicable):
  • Neck seal closes in the front via 2 small black snaps.


TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


Fox Shoulders Phase2.jpg Shoulder Armor
For 501st approval:
  • Shoulders are painted satin or matte white.
  • The left shoulder has the emblem of the galactic senate painted in crimson.
  • Shoulders are tear drop in shape with all rounded edges.
  • Shoulder armor is not symmetrical.
    • The shoulders slightly curve back at the bottom.
  • Armor is weathered with shades of grey.


Fox s4 biceps.jpg Upper Arm Armor
For 501st approval:
  • Biceps are cylindrical with no detail/sculptural features.
  • Biceps are painted crimson.
  • Biceps have 2 white stripes around the entire bicep. The top of the upper stripe is approximately half way down the bicep. The bottom stripe sits approximately 1/4” off the bottom of the bicep.
  • Armor is weathered with shades of grey.


Fox s4 forearms.jpg Forearm Armor
For 501st approval:
  • Armour is painted crimson.
  • Right forearm has a compad with 8 small buttons, 1 large main button, and 1 slightly small rectangular button. The compad is painted white and weathered with shades of grey.
  • Armour is seamless on the outside edge.
    • Due to the shape of the armour, a butted seam is acceptable on the inside if required.
  • Elbow plate is integrated into the forearm and does not extend past the arm.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
Fox s4 handplates.jpg Hand Plates
For 501st approval:
  • Armor is painted dark scarlet.
  • Hand plates are mirror images of each other.
  • Armor is weathered with shades of grey.



Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
  • Gloves cover any exposed skin.
  • Gloves do not show any labels or logos when the armor is worn.


Fox s4 chest.jpg Chest Armor
For 501st approval:
  • Armour is painted crimson.
  • The pecs of the chest are painted satin or matte white.
  • Lower portion of the chest has an angular notch for the abdomen armour to fit into.
  • Chest and back plate match together at the sides and shoulder with no gap.
  • Each side has a butted seam line where the front and back halves come together.
  • Dark scarlet shoulder straps are placed underneath the chest to connect to the back.
  • Armor is weathered with shades of grey.


Fox s4 back.jpg Back Armor
For 501st approval:
  • Armour is painted crimson.
  • Rear tank has detailed area that contains 4 circles.
  • Under the circles, at the left side of the back, there are two parallel blocks and to the right of the back there are 3 parallel blocks.
    • All details painted dark grey.
  • Dark scarlet shoulder straps are placed underneath the chest to connect to the back.
  • Armor is weathered with shades of grey.


Fox s4 ab.jpg Abdomen Armor
For 501st approval:
  • Armour is painted crimson.
  • Top edge of the armour is angled to match the chest.
  • The ab armour protrudes out in the middle to better up with the chest.
  • 4 inset lines divide the ab plate into segments.
  • A butted seam between the ab plate and kidney is acceptable.
  • Armor is weathered with shades of grey.


Fox s4 kidney.jpg Kidney Armor
For 501st approval:
  • Armour is painted crimson.
  • A butted seam between ab plate and kidney is acceptable.
  • 2 inset lines divide the kidney plate into sections.
  • Armor is weathered with shades of grey.


Fox s4 cod.jpg Cod and Posterior Armor
For 501st approval:
  • Armour is painted crimson.
  • Cod and posterior armour connect at the hips with a neat butted seam line.
  • Armor is weathered with shades of grey.


Fox s4 butt.jpg Belt and Ammo Box's
For 501st approval:
  • Belt is approximately 3” tall and divided into 1.75” wide segments. The front segments have a key/slot detail.
  • Belt boxes are mounted at the hips.
    • Butted seams are permitted at the connection if required.
  • Belt and belt boxes are painted satin or matte white.
  • Detonator is centred on the back of the belt with no control buttons. The detonator has 2 lines set in approx. ½”-5/8” from the edges. Lines may be recessed or painted on.
  • Detonator is painted crimson.
  • The inside of the detonator end caps is painted dark grey.
  • Armor is weathered with shades of grey.


Fox s4 Kama.jpg Kama
For 501st approval:
  • The kama is made of black leather, leather like material, or heavy canvas.
  • The kama has primer grey trim.
  • The front edges of the kama line up with the outside edges of the front two panels of the belt.
  • The back of the kama is split all the way up to the belt.
  • The bottom edges of the kama are rounded.
  • The kama extends to the middle of the knee.


150px Holsters
For 501st approval:
  • Holsters are painted satin or matte white.
  • Holsters connect to the belt via straps.
    • Straps are painted matte or satin white.
  • Armor is weathered with shades of grey.


Fox s4 thighs.jpg Thigh Armor
For 501st approval:
  • Armour is painted crimson.
  • Front thigh armour has a flat triangular area near the knee with a notch cut out for the knee armour. From the top of the triangle a ridge line travels up the front of the thigh to the top.
  • Armour is seamless.
    • No visible traces of how the armour was assembled are shown.
  • Rear of the thigh has an indentation.
  • Armor is weathered with shades of grey.


Fox s4 shins.jpg Lower Leg Armor
For 501st approval:
  • Armour is painted matte or satin white.
  • Knee armour is intergrated with the lower leg.
  • Knee armour is painted crimson.
  • The armour has a flat centre triangle below the knee plate, with the single point facing downward.
  • The calf detail of the armour has a ridge wrapping around the back of the leg.
  • Back of the lower legs have an indentation just under the calf to follow down to the ankle.
  • Calf can have an access area on the inside of the leg.
    • The outside of the calf is closed.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Calves are seamless with a trap door access through the indent in the rear of the lower leg.
Fox s4 boots.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armour. Boots are lace-less and have flat soles.
  • Boots have a cenre strip running from the toe to the ankle, a strap across the top fo the foot, and 2 flat white discs on either side of the foot, terminating the strap.
  • Soles are crimson.
  • Boots are weathered with shades of grey.
For level two certification (if applicable):
  • Boots have accurate notched sole.
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.


CRLdc15s-animated.jpg DC-15S Blaster Carbine (animated style)
For 501st approval:

Manufactured by BlasTech Industries, this weapon is commonly carried by the Troopers of the Galactic Republic.

  • This is the animated variant of the DC-15S blaster rifle.



Dc15a Animated.jpg DC-15A Blaster Rifle (animated style)
For 501st approval:

Manufactured by BlasTech Industries, this blaster is the standard issue weapon carried by the Clone Troopers of the Grand Army of the Republic.

  • This is the animated variant of the DC-15A blaster rifle.


This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:CC_-_Commander_Fox_Phase_2

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.