(Difference between revisions)
Line 15: Line 15:
*Helmet has no mohawk
*Helmet has no mohawk
*Cheeks are filled in and replaced with "mud flaps" wrapping the face. This will be grey in color. There are three vents on the cheeks near the eyes on each side of the face.
*Cheeks are filled in and replaced with "mud flaps" wrapping the face. This will be grey in color. There are three vents on the cheeks near the eyes on each side of the face.
-
*Helmet frown is charcoal gray in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown. Only two nose vents should be present.
+
*Helmet frown is charcoal gray in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown. Only two nose vents are present.
*Primer gray stripe around back of dome. There is also a think black line the follows the bottom of the gray stripe that wraps around the dome
*Primer gray stripe around back of dome. There is also a think black line the follows the bottom of the gray stripe that wraps around the dome
-
*Helmet has draping dome that covers the back of the head. On each side where the ears would be two protruding platforms should be there. On the left side of the helmet, there should be a gray antenna with a black base.
+
*Helmet has draping dome that covers the back of the head. On each side, where the ears would be, two protruding platforms are present. On the left side of the helmet, there is a gray antenna with a black base.
*On the face of the dome over the right eye there are 2 .25 inch red dots horizontal to the ground.  
*On the face of the dome over the right eye there are 2 .25 inch red dots horizontal to the ground.  
*There is another set of red dots located behind the left antenna platform.|
*There is another set of red dots located behind the left antenna platform.|
-
*Helmet has the appearance of a neck ring. |
+
*Helmet has the appearance of a neck ring.|
-
*Helmet has an enclosed complete neck ring that seals the helmet to the neck. }}
+
*Helmet has an enclosed complete neck ring that seals the helmet to the neck.}}
{{CRL-realistic-clone-neckseal}}
{{CRL-realistic-clone-neckseal}}
Line 27: Line 27:
{{CRL-generic-undersuit}}
{{CRL-generic-undersuit}}
-
{{CRLtemplate|File:Bacara_shoulders.jpg|Shoulder Bells|
+
{{CRLtemplate-onelevel|File:Bacara_shoulders.jpg|Shoulder Bells|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
*Shoulders should be tear drop in shape with all rounded edges. | |
+
*Shoulders are tear drop in shape with all rounded edges.|
-
*Shoulder bells should not be symmetrical. The Shoulder bells should slightly curve back at the bottom of the shoulder. }}
+
*Shoulder bells are not symmetrical.
 +
**The Shoulder bells slightly curve back at the bottom of the shoulder.|}}
-
{{CRLtemplate|File:Bacara_upper_arms.jpg|Upper Arm Armor|
+
{{CRLtemplate-nolevels|File:Bacara_upper_arms.jpg|Upper Arm Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
*Should have a dimple on the lower area of the back of the arm.  The outside of the bicep should have a hard line edge at the front that turns in.  The inside of the upper arm should be rounded.
+
*There is a dimple on the lower area of the back of the arm.  The outside of the bicep has a hard line edge at the front that turns in.  The inside of the upper arm is rounded.
-
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.| | }}
+
*Armor is seamless.
 +
**No visible traces of how the armor was assembled are shown||}}
-
{{CRLtemplate|File:Bacara_elbows.jpg|Elbow Armor|  
+
{{CRLtemplate-onelevel|File:Bacara_elbows.jpg|Elbow Armor|  
-
*Armor should be painted matte or satin white
+
*Armor is painted matte or satin white
-
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
+
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there are detail slots that look like an equal symbol on both elbow pieces.
-
* Both elbows have strapping. The straps should have a raised detail line at the top and bottom of the strap.| |
+
*Both elbows have strapping.
-
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}
+
**The straps have a raised detail line at the top and bottom of the strap.|
 +
*Elbows are mirror images of each other with a notched area on the outside of the elbow above the detail marks.|}}
-
{{CRLtemplate|File:Bacara_forearms.jpg|Forearm Armor|
+
{{CRLtemplate-onelevel|File:Bacara_forearms.jpg|Forearm Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
*Both left and right forearms should be mirror images of each other.
+
*Both left and right forearms are mirror images of each other.
-
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectanular button.
+
*Right forearm has a compad with 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
-
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.  
+
*Forearm tops have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.  
-
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. | |
+
*Armor is seamless.
 +
**No visible traces of how the armor was assembled are shown.|
*Compad has detail antenna on its left.  
*Compad has detail antenna on its left.  
-
*Instead of a hard edge the top of the forearm has a bone ridge.}}
+
*Instead of a hard edge the top of the forearm has a bone ridge.|}}
-
{{CRLtemplate|File:Bacara_handplates.jpg|Hand Plates|
+
{{CRLtemplate-nolevels|File:Bacara_handplates.jpg|Hand Plates|
-
*Armor should be painted matte or satin white
+
*Armor is painted matte or satin white
*Hand plates are mirror images of each other.   
*Hand plates are mirror images of each other.   
-
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}
+
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.||}}
{{CRLtemplate|File:Generic-black-gloves.jpg|Gloves|
{{CRLtemplate|File:Generic-black-gloves.jpg|Gloves|
-
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. | | }}
+
*Black over the wrist gloves made of leather, nylon, or other low pile fabrics. *Gloves do not show any labels or logos once the armor is on and cover any exposed skin.||}}
-
{{CRLtemplate|File:Bacara_chest.jpg|Chest Armor|
+
{{CRLtemplate-onelevel|File:Bacara_chest.jpg|Chest Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
*Two detail slots on right breast.
*Two detail slots on right breast.
-
*Chest and back plate should match together at the sides with no gap, just a seam line.  
+
*Chest and back plate match together at the sides with no open gap, just a seam line.
-
*Shoulder straps should be placed underneath the chest to connect to the back. |
+
*Shoulder straps are placed underneath the chest to connect to the back.|  
-
|
+
*Shoulder straps are slotted into the chest into the detail ridges of the top connection points.|}}
-
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points. }}
+
-
{{CRLtemplate|File:Bacara_back.jpg|Back Armor|
+
{{CRLtemplate-nolevels|File:Bacara_comm_harness.jpg|Command Harness|
-
*Armor should be painted matte or satin white.
+
*Right shoulder has a maroon colores spaulder placed over it.
-
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
+
**The spaulder cups over the shoulder bell and does not appear to be a flap or flimsy.
-
*Top of the tank has a thermal detonator with three buttons.
+
**This will attach also to a shoulder cover harness over the right shoulder strap.
-
*in the recess under the back tank, there should be two radio boxes.
+
-
*Chest and back plate should match together at the sides with no gap, just a seam line.
+
-
*Shoulder straps should be placed underneath the chest to connect to the back. |
+
-
|
+
-
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
+
-
*Highly detailed resin insert should replace softer details. }}
+
-
 
+
-
{{CRLtemplate|File:Bacara_comm_harness.jpg|Command Harness|
+
-
*Right shoulder will have maroon color spaulder placed over it. It should cup over the shoulder bell and not appear to be a flap or flimsy. This will attach also to a shoulder cover harness over the right shoulder strap.
+
*Right chest has an angular looking plate that is grey in color and has a diagonal maroon color stripe across it.  
*Right chest has an angular looking plate that is grey in color and has a diagonal maroon color stripe across it.  
-
*The two black belts that cross the chest will connect behind this plate. On the belt that crosses the chest to the left side front belt box, a metal or metal like buckle should be secured. The other belt connects to the right front belt box.
+
*The two black belts that cross the chest will connect behind this plate. On the belt that crosses the chest, to the left side front belt box, a metal or metal like buckle is secured. The other belt connects to the right front belt box.
-
*One black belt will drape down from the shoulder and connect to the rear right belt box. | | }}
+
*One black belt will drape down from the shoulder and connect to the rear right belt box.||}}
 +
 
 +
{{CRLtemplate-onelevel|File:Bacara_back.jpg|Back Armor|
 +
*Armor is painted matte or satin white.
 +
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there are two parallel lines and the the right of the back there is a squared detail.
 +
*Top of the tank has a thermal detonator with three buttons.
 +
*in the recess under the back tank, there are two radio boxes.
 +
*Chest and back plate match together at the sides with no gap, just a seam line.
 +
*Shoulder straps are placed underneath the chest to connect to the back.|
 +
*Shoulder straps are slotted into the back armor, into the detail ridges of the top connection points.
 +
*Highly detailed resin insert should replace softer details.|}}
-
{{CRLtemplate|File:Bacara_ab.jpg|Ab Armor|
+
{{CRLtemplate-onelevel|File:Bacara_ab.jpg|Ab Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
-
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
+
*Ab section wraps around the wearers body and is sealed at the sides or at the back.
-
*Ab section should be completely contained under the chest and back armor. |
+
*Ab section is completely contained under the chest and back armor.|
-
|
+
*Ab section is seamless at the sides and close in the back.
-
* Ab section should be seamless at the sides and close in the back. A detail plate should cover the seam line and hide all work.}}
+
**A detail plate covers the seam line and hides all work.|}}
-
{{CRLtemplate|File:Bacara_codbutt.jpg|Cod and Posterior Armor|
+
{{CRLtemplate-onelevel|File:Bacara_codbutt.jpg|Cod and Posterior Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
*Cod and Posterior armor should connect at the hips. | |
+
*Cod and Posterior armor connect at the hips.|
-
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}
+
*Hips are connected via a snap with the correct detailed shape of the armor at the connection point.|}}
-
{{CRLtemplate|File:Bacara_belt.jpg|Belt|
+
{{CRLtemplate-onelevel|File:Bacara_belt.jpg|Belt|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
*Ammo Belt with boxes and detonator.
*Ammo Belt with boxes and detonator.
*Detonator is centered on the back of belt.  
*Detonator is centered on the back of belt.  
-
*8 boxes total, 4 on each side of abdomen and attached to the belt. |
+
*8 boxes total, 4 on each side of abdomen and attached to the belt.|
-
|
+
*Belt Boxes are notched and fitted flush with the details of the belt.
-
*Belt Boxes should be notched and fitted flush with the details of the belt.
+
*Left Rear belt box has two square buttons in the top left corner and and equal symbol detail at the bottom right.
-
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
+
*Right Rear belt box has a bar with two small cylinders centered with and equal symbol detail on the bottom left.
-
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
+
*From the rear two belt boxes the belt has a ribbed detailed appearance.|}}
-
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}
+
-
{{CRLtemplate|File:Bacara_kama.jpg|Kama|
+
{{CRLtemplate-nolevels|File:Bacara_kama.jpg|Kama|
-
*Kama should be maroon matching the color of the spaulder and rank stripe on the chest plate. The rear of the Kama has a triangle split. Kama should start at the front belt boxes. Kama should be from a heavy material like denim or duck cloth. Leather or vinyl is not correct. Kama should flow to the bottom of your knee armor. Approximately 6 inches below your front belt boxes, a thin, white, .5 inch strap with metal clip should be attached to clip onto the command buckle that is attached to the belt. | | }}
+
*Kama is maroon, matching the color of the spaulder and rank stripe on the the chest plate.
 +
*The rear of the Kama has a triangle split.
 +
*Kama starts at the front belt boxes.
 +
*Kama is made from a heavy material like denim or duck cloth.
 +
**Leather or vinyl is not correct.
 +
*Kama flows to the bottom of the knee armor.
 +
*Approximately 6 inches below the front belt boxes, a thin, white, 1/2 inch strap with metal clip is attached to clip onto the command buckle that is attached to the belt.||}}
-
{{CRLtemplate|File:Bacara_thighs.jpg|Thigh Armor|
+
{{CRLtemplate-onelevel|File:Bacara_thighs.jpg|Thigh Armor|
-
*Armor should be painted matte or satin white.  
+
*Armor is painted matte or satin white.  
-
* Front of thigh armor should have a flat triangular area near the knee.  From the top of the triangle a ridge line should go up the front of the thigh to the top.
+
*Front of thigh armor has a flat triangular area near the knee.  From the top of the triangle a ridge line travels up the front of the thigh to the top.
-
*Rear of the thigh should have an indention.
+
*Rear of the thigh has an indention.
-
*Armor should be seamless. No visible traces of how the armor was assembled should be shown. |
+
*Armor is seamless.
-
|
+
**No visible traces of how the armor was assembled are shown.|
-
* Outside of lower portion of the thighs should come to a point and inner lower end should be rounded. }}
+
*Outside of lower portion of the thighs comes to a point and inner lower end should be rounded.|}}
-
{{CRLtemplate|File:Bacara_knees.jpg|Knee Armor|
+
{{CRLtemplate-onelevel|File:Bacara_knees.jpg|Knee Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
*Knees should wrap around the front of the leg. From top center a raised detail line should be present.
+
*Knees wrap around the front of the leg.
-
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
+
*From top center a raised detail line is present.
-
|
+
*Knees are strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.|
-
*Center strap should be primer gray.
+
*Center strap is colored primer gray.
-
*Connection between the knee and the strapping should have a detail clip.}}
+
*Connection between the knee and the strapping has a detail clip.|}}
-
{{CRLtemplate|File:Bacara_shins.jpg|Lower Leg Armor|
+
{{CRLtemplate-onelevel|File:Bacara_shins.jpg|Lower Leg Armor|
-
*Armor should be painted matte or satin white.
+
*Armor is painted matte or satin white.
-
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
+
*Lower Legs are mirror images of each other.
-
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
+
*The front of the armor pieces have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
-
*Calf can have an access area on the inside of the leg. The outside of the calf should be closed. |
+
*Back of the lower legs have an indentation, just under the calf, that follows down to the ankle.
-
|
+
*Calf can have an access area on the inside of the leg.
-
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.}}
+
**The outside of the calf is closed.|
 +
*Calves are seamless and have a trap door access through the indent in the rear of the lower leg.|}}
-
{{CRLtemplate|File:Bacara_boots.jpg|Boots|
+
{{CRLtemplate-nolevels|File:Bacara_boots.jpg|Boots|
-
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles. The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap. There should be no markings or labels from the shoe makers. Boot soles should be primer gray. | | }}
+
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles. The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap. There are no markings or labels from the shoe makers. Boot soles are primer gray.||}}
{{CRLaccessories}}
{{CRLaccessories}}

Revision as of 16:32, 17 May 2014

crlblackhd.gif
Clone Commander Bacara
Bacara mainpic.jpg
Model CC4841, Photo by Sharon Langthorne


Clone-Trooper-Detachment.png

Description: Clone Commander Bacara
Prefix: CC
Detachment: Clone Trooper Detachment
Context: Episode III: Revenge of the Sith
CC-1138, also known as "Bacara," was a clone marshal commander who served in the Grand Army of the Republic. He was selected to be part of the initial ARC training program under the command of Alpha-17. During this time he developed a reputation as a loner. His loner's reputation carried over into his career as a soldier, but it never stopped him from putting the needs of his troops ahead of his own.Upon completion of his ARC training, CC-1138 used his newly acquired knowledge to turn the Galactic Marines into a highly efficient ground unit. Following continued action in the Outer Rim Sieges, Bacara and Ki-Adi-Mundi were ordered to the snow-covered world Mygeeto. While stationed on Mygeeto, Bacara was given Order 66 and gunned down Jedi Master Ki-Adi-Mundi.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
  • Any uncertainties or questionable aspects of the submitted costume should be brought to the appropriate DL/GML peer review section of the legion forum.
Required Costume Components

The following costume components are present and appear as described below.

Bacara helmet.jpg Helmet
For 501st approval:
  • Episode 3 style Clone Helmet - Fanmade bucket.
  • Visor - Black Visor
  • Helmet has no mohawk
  • Cheeks are filled in and replaced with "mud flaps" wrapping the face. This will be grey in color. There are three vents on the cheeks near the eyes on each side of the face.
  • Helmet frown is charcoal gray in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown. Only two nose vents are present.
  • Primer gray stripe around back of dome. There is also a think black line the follows the bottom of the gray stripe that wraps around the dome
  • Helmet has draping dome that covers the back of the head. On each side, where the ears would be, two protruding platforms are present. On the left side of the helmet, there is a gray antenna with a black base.
  • On the face of the dome over the right eye there are 2 .25 inch red dots horizontal to the ground.
  • There is another set of red dots located behind the left antenna platform.
For level two certification (if applicable):
  • Helmet has the appearance of a neck ring.
For level three certification (if applicable):
  • Helmet has an enclosed complete neck ring that seals the helmet to the neck.


Clone trooper neck seal.jpg Neck Seal
For 501st approval:
  • Neck seal is black in color with vertical ribbing or being smooth in appearance.
  • No logos or labels are visible.
    • If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.



TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


Bacara shoulders.jpg Shoulder Bells
For 501st approval:
  • Armor is painted matte or satin white.
  • Shoulders are tear drop in shape with all rounded edges.
For level two certification (if applicable):
  • Shoulder bells are not symmetrical.
    • The Shoulder bells slightly curve back at the bottom of the shoulder.
Bacara upper arms.jpg Upper Arm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • There is a dimple on the lower area of the back of the arm. The outside of the bicep has a hard line edge at the front that turns in. The inside of the upper arm is rounded.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown


Bacara elbows.jpg Elbow Armor
For 501st approval:
  • Armor is painted matte or satin white
  • There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there are detail slots that look like an equal symbol on both elbow pieces.
  • Both elbows have strapping.
    • The straps have a raised detail line at the top and bottom of the strap.
For level two certification (if applicable):
  • Elbows are mirror images of each other with a notched area on the outside of the elbow above the detail marks.
Bacara forearms.jpg Forearm Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Both left and right forearms are mirror images of each other.
  • Right forearm has a compad with 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
  • Forearm tops have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
For level two certification (if applicable):
  • Compad has detail antenna on its left.
  • Instead of a hard edge the top of the forearm has a bone ridge.
150px Hand Plates
For 501st approval:
  • Armor is painted matte or satin white
  • Hand plates are mirror images of each other.
  • Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.


Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics. *Gloves do not show any labels or logos once the armor is on and cover any exposed skin.
For level two certification (if applicable):
For level three certification (if applicable):
Bacara chest.jpg Chest Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Two detail slots on right breast.
  • Chest and back plate match together at the sides with no open gap, just a seam line.
  • Shoulder straps are placed underneath the chest to connect to the back.
For level two certification (if applicable):
  • Shoulder straps are slotted into the chest into the detail ridges of the top connection points.
Bacara comm harness.jpg Command Harness
For 501st approval:
  • Right shoulder has a maroon colores spaulder placed over it.
    • The spaulder cups over the shoulder bell and does not appear to be a flap or flimsy.
    • This will attach also to a shoulder cover harness over the right shoulder strap.
  • Right chest has an angular looking plate that is grey in color and has a diagonal maroon color stripe across it.
  • The two black belts that cross the chest will connect behind this plate. On the belt that crosses the chest, to the left side front belt box, a metal or metal like buckle is secured. The other belt connects to the right front belt box.
  • One black belt will drape down from the shoulder and connect to the rear right belt box.


Bacara back.jpg Back Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there are two parallel lines and the the right of the back there is a squared detail.
  • Top of the tank has a thermal detonator with three buttons.
  • in the recess under the back tank, there are two radio boxes.
  • Chest and back plate match together at the sides with no gap, just a seam line.
  • Shoulder straps are placed underneath the chest to connect to the back.
For level two certification (if applicable):
  • Shoulder straps are slotted into the back armor, into the detail ridges of the top connection points.
  • Highly detailed resin insert should replace softer details.
Bacara ab.jpg Ab Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
  • Ab section wraps around the wearers body and is sealed at the sides or at the back.
  • Ab section is completely contained under the chest and back armor.
For level two certification (if applicable):
  • Ab section is seamless at the sides and close in the back.
    • A detail plate covers the seam line and hides all work.
Bacara codbutt.jpg Cod and Posterior Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Cod and Posterior armor connect at the hips.
For level two certification (if applicable):
*Hips are connected via a snap with the correct detailed shape of the armor at the connection point.
Bacara belt.jpg Belt
For 501st approval:
  • Armor is painted matte or satin white.
  • Ammo Belt with boxes and detonator.
  • Detonator is centered on the back of belt.
  • 8 boxes total, 4 on each side of abdomen and attached to the belt.
For level two certification (if applicable):
  • Belt Boxes are notched and fitted flush with the details of the belt.
  • Left Rear belt box has two square buttons in the top left corner and and equal symbol detail at the bottom right.
  • Right Rear belt box has a bar with two small cylinders centered with and equal symbol detail on the bottom left.
  • From the rear two belt boxes the belt has a ribbed detailed appearance.
Bacara kama.jpg Kama
For 501st approval:
  • Kama is maroon, matching the color of the spaulder and rank stripe on the the chest plate.
  • The rear of the Kama has a triangle split.
  • Kama starts at the front belt boxes.
  • Kama is made from a heavy material like denim or duck cloth.
    • Leather or vinyl is not correct.
  • Kama flows to the bottom of the knee armor.
  • Approximately 6 inches below the front belt boxes, a thin, white, 1/2 inch strap with metal clip is attached to clip onto the command buckle that is attached to the belt.


Bacara thighs.jpg Thigh Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Front of thigh armor has a flat triangular area near the knee. From the top of the triangle a ridge line travels up the front of the thigh to the top.
  • Rear of the thigh has an indention.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
For level two certification (if applicable):
  • Outside of lower portion of the thighs comes to a point and inner lower end should be rounded.
Bacara knees.jpg Knee Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Knees wrap around the front of the leg.
  • From top center a raised detail line is present.
  • Knees are strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.
For level two certification (if applicable):
  • Center strap is colored primer gray.
  • Connection between the knee and the strapping has a detail clip.
Bacara shins.jpg Lower Leg Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Lower Legs are mirror images of each other.
  • The front of the armor pieces have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
  • Back of the lower legs have an indentation, just under the calf, that follows down to the ankle.
  • Calf can have an access area on the inside of the leg.
    • The outside of the calf is closed.
For level two certification (if applicable):
  • Calves are seamless and have a trap door access through the indent in the rear of the lower leg.
Bacara boots.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor. Boots must be lace-less and have flat soles. The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap. There are no markings or labels from the shoe makers. Boot soles are primer gray.


Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.


DC15 carbine.jpg DC-15S Blaster
For 501st approval:

Manufactured by BlasTech Industries the DC-15S is smaller in scale than the DC-15A blaster rifle. Although it has a shorter range than that of the "A" model, it is easier to handle with a higher rate of fire. It features a folding stock for braced firing.

  • Blaster rifle may be scratch built out of plastic, wood, metal or cast in resin.
  • Total length should be approximately 26 “or 66 cm.
  • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • Folding stock (does not need to function).
  • A total of (12) radiator fins are present on the barrel.
  • Spare igniter is present on both sides of barrel.
  • Charge magazine is present on the right side.
For level three certification (if applicable):
  • Charge magazine is metal to gun metal grey in color.
  • Any bolts and screws are metal to gun metal grey in color.
  • Parts of the spare igniter are copper in color.
  • Blaster is weathered.


DC15 rifle.jpg DC-15A Blaster Rifle
For 501st approval:

Manufactured by BlasTech Industries, the DC-15A is a tibanna gas, cartridge powered weapon. Hyper-ionized blue plasma bolts are more than capable of penetrating armored units. Exceptionally effective against both droids and contemporary targets.

  • Blaster rifle is scratch built out of plastic, wood, metal or cast in resin.
  • Total length is approximately 55 inches (139.7 cm).
    • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • A total of (10) radiator fins are present on the barrel.
  • A power setting adjuster is present.
  • The correct style of sniper scope is present.
  • Charge magazine lock is present on the left side.
  • Power setting adjuster, sniper scope and charge magazine lock is metal to gun metal gray in color.
For level three certification (if applicable):
  • Sniper scope is able to be removed from storage position (bottom of rifle) and attached to the top of the rifle.
  • Parts of the spare igniter are copper in color.
  • Front optical sight is able to flip to the up position.
  • Any bolts and screws are metal to gun metal grey in color.
  • Blaster is weathered.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:CC_-_Commander_Bacara

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.