(Difference between revisions)
(31 intermediate revisions not shown)
Line 1: Line 1:
-
{{CRLheader|Commander Appo (Comic Version)|File:Missingprofile.jpg|MODEL NAME|PHOTOGRAPHER NAME}}
+
{{CRLheader|Commander Appo (ROTS Style)|File:Appo.jpg|CC 5298|Joe P.}}
-
{{CRLdetinfo| 1111 |Commander Appo (Comic Version)|CC|Star Wars comic : Dark Times #4:|
+
{{CRLdetinfo|1111|Commander Appo (ROTS Style)|CC|Expanded universe storyline and Hasbro action figures|
-
Appo wore this version of the armor while serving aboard Vader's Imperator-class Star Destroyer, the "Exactor". Working with Clone Commander Vill, Appo oversaw the removal of  Separatist forces from their holdout worlds.}}
+
Appo wore this version of the armor while serving aboard Vader's Imperator-class Star Destroyer, the "Exactor". Working with Clone Commander Vill, Appo oversaw the removal of  Separatist forces from their holdout worlds.
 +
Shown here is the Regiment Commander version of Appo's armor, sporting the blue markings of the 501st.}}
{{CRLctnlevels}}
{{CRLctnlevels}}
-
{{CRLwiplmoapproval}}
+
{{CRLgmlapproval}}
{{CRLrequirements}}
{{CRLrequirements}}
-
{{CRLtemplate|File:E3 Clone Helmet.jpg | Helmet|
+
{{CRLtemplate-onelevel|File:Appo_Helmet.jpg|Helmet|
-
*Episode 3 style Clone Helmet - Fanmade bucket. Some "name brand" helmets may be unacceptable.
+
*Realistic style ROTS Phase II helmet.
-
*Helmet must be painted matte or satin white.
+
**Fan-made helmet.
-
*Visor - Mirrored Chrome or Black Visor
+
**Some "name brand" helmets may be unacceptable.
-
*Mohawk on dome has raised edges on the outside edges of the top.
+
*Helmet is painted matte or satin white.
-
*Tube stripes on each side are dark blue in color. There are 9 stripes per side
+
*Black eye lens.
-
*Frown is charcoal grey in color and has 7 teeth – 1 in the middle and three on each side. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
+
*Helmet Mohawk on dome.
-
*Primer grey stripe around back of dome.
+
*Helmet has a black brow band, just above the eye lens, that extends around to the back of helmet.
-
*Bar above the visor wrapping around the sides is painted black.
+
*Blue stripe runs vertically up front of helmet starting at chin and widens as it continues on top of dome.
-
*Vocoder (chip detail) is painted black.
+
*Helmet frown is charcoal grey in color.
-
*Aerators (cylinders on either side of the vocoder) are painted black, with the center round part painted silver.
+
**Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
-
*Ear bars are painted a dark grey.  The raised edge around the ear cap is painted black.
+
*Stripe running up between vocoder and frown is about 1 inch wide.
-
*Rectangular “grid” on back of helmet painted black.|
+
*Stripe edges, along center of T lens, are about 3/8 inch wide at bottom and expand to about 5/8 inch near top.
-
*Helmet has the appearance of a neck ring. |
+
**Stripe continues above eye lens with about a 3 width and expands upward to align with blue on dome.
 +
**Stripe above black band is about 3 1/2 inches wide and expands outward to about 4 5/8 inch at front edge of mowhawk.
 +
**Stripe at center of dome is about 2 3/4 inches from edge of mohawk.
 +
**Stripe narrows slightly toward back of dome and is about 6 inches wide, and stops short of dome edge leaving about a 3/8 inch white border just above the grey indented band.
 +
*Black aerators with metal grills are mounted inside the two indented front jaw tubes at base of helmet.
 +
*Ear caps are dark grey with black edging and detail.
 +
*(9) dark blue vertical hash marks on each side of helmet cheek.
 +
*Grey indented helmet band around back of dome.
 +
*Black Indented vertical rectangle area on back with ribbed detail.
 +
*Armor is weathered with shades of grey.|
*Helmet has an enclosed complete neck ring that seals the helmet to the neck.}}
*Helmet has an enclosed complete neck ring that seals the helmet to the neck.}}
Line 31: Line 41:
{{CRL-generic-undersuit}}
{{CRL-generic-undersuit}}
-
{{CRLtemplate|File:Appo_Comic_Pauldron.jpg |Command Pauldron|
+
{{CRLtemplate-nolevels|File:Appo_Pauldron.jpg|Command Pauldron|
-
*Pauldron is Episode III style.
+
*Realistic style Phase II (Episode III) Pauldron.
-
*Shoulder mantle and paneling is colored black.||}}
+
*Pauldron has a black leather or vinyl base with wedge shaped panel details.
 +
*Small black angled shoulder plate is attached to base over right shoulder.
 +
*Larger angled shoulder plate is attached to base over left sholder and is blue.
 +
*Ammo strap attaches to front right of pauldron base.||}}
-
{{CRLtemplate|File:501st clone shoulder bells2.jpg|Shoulder Bells|
+
{{CRLtemplate-nolevels|File:Appo_Comic_Shoulders.jpg|Shoulder Armor|
-
*Armor is painted blue.
+
*Realistic style shoulder armor.
-
*Shoulders should be tear drop in shape with all rounded edges.||
+
*Shoulders are tear drop in shape with all rounded edges.  
-
*Shoulder bells should not be symmetrical. The pieces slightly curve back at the bottom of the shoulder.}}
+
*Armor is painted blue.
 +
*Armor is weathered with various scuff marks and shades of grey.|}}
-
{{CRLtemplate|File:Clone_Biceps.jpg|Upper Arm Armor|
+
{{CRLtemplate-nolevels|File:Appo_Biceps.jpg|Upper Arm Armor|
-
*Armor should be painted matte or satin white.
+
*Realistic style Upper Arm Armor.
-
*Should have a dimple on the lower area of the back of the arm. The outside of the bicep should have a hard line edge at the front that turns in. The inside of the upper arm should be rounded.||
+
*Armor is painted matte or satin white.
-
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.}}
+
*Armor has a front hard line outside edge and inside rounded edge.
 +
**Armor piece has a dimple on the lower area of the back of the arm.
 +
*Armor is seamless.
 +
**No visible traces of how the armor was assembled are shown.
 +
*Armor is weathered with shades of grey.||}}
-
{{CRLtemplate|‎File:Clone elbow copy.jpg|Elbow Armor|
+
{{Elbow_Armor_Realistic}}
-
*Armor should be painted matte or satin white.
+
-
*There are two elbows. On each elbow on the outside of the body near the connection point of the elbow strap there should be detail slots that look like an equal symbol on both elbow pieces.
+
-
* Both elbows have strapping.  The straps should have a raised detail line at the top and bottom of the strap.||
+
-
*Elbows should be mirror images of each other with a notched area on the outside of the elbow above the detail marks.}}
+
-
{{CRLtemplate|File:Clone_gauntlets_copy.jpg|Forearm Armor|
+
{{CRLtemplate-nolevels|File:Appo_Forearms.jpg|Forearm Armor|
-
*Armor should be painted matte or satin white.
+
*Realistic style forearm armor.
-
*Both left and right forearms should be mirror images of each other.
+
*Armor is painted matte or satin white.
-
*Right forearm should have a compad that has 8 small buttons,1 Large main button, and 1 slightly smaller rectangular button.
+
*Wrist end of forearm has a blue stripe, about 3/4 inch wide and spaced about 1/4 from wrist edge, wrapped around the armor.
-
*Forearm tops should have a flattened triangular area that have a ridge that comes to a point at the top of the forearm.
+
*Right forearm has a compad with 8 small buttons,1 large main button, and 1 slightly smaller rectangular button closest to the elbow.
-
*The wrist of the forearm must have a blue stripe that wraps around the entire circumference of the forearm.||
+
*Armor is seamless.
-
*Compad has detail antenna on its left.
+
**No visible traces of how the armor was assembled are shown.  
-
*Instead of a hard edge the top of the forearm has a bone ridge.
+
*Armor is weathered with various scuff marks and shades of grey.||}}
-
*Armor should be seamless.  No visible traces of how the armor was assembled should be shown.}}
+
-
{{CRLtemplate|File:Clone_Hand_Guards.jpg|Hand Plates|
+
{{Hand_Plates_Realistic}}
-
*Armor should be painted matte or satin white.
+
-
*Hand plates are mirror images of each other.
+
-
*Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand. | | }}
+
{{CRL-generic_black_gloves}}
{{CRL-generic_black_gloves}}
-
{{CRLtemplate|File:Clone chest copy.jpg|Chest Armor|
+
{{CRLtemplate-nolevels|File:Appo_Chest.jpg|Chest Armor|
-
*Armor should be painted matte or satin white.
+
*Realistic style Chest Armor.
-
*Two detail slots on the bottom right of the right breast.
+
*Armor is painted matte or satin white.
-
*Chest and back plate should match together at the sides with no gap, just a seam line.  
+
*Two detail slots on lower outside edge of right raised chest area.
-
*Shoulder straps should be placed underneath the chest to connect to the back. ||
+
*Armor has blue pillar “A” shape design pattern that runs up the center of chest.
-
* Shoulder straps should be slotted into the chest into the detail ridges of the top connection points.}}
+
**Blue pillar design is narrowest at top with about 1 3/4 inch width and widens downward.
 +
*Design is about 3 1/2 inches wide at the elevated chest edge, and about 6 inches wide at bottom, just above top abdomen edge.
 +
*Blue pillar design flares outward along bottom edge, about 3 1/2 inches in length, creating about a 3/4 inch blue border on surface that tappers to about 1/2  inch. Blue carries over beveled indented edge along abdomen. Flares end in vertical cut edges.
 +
**Two white rectangles aligned vertically in center create the “A” shape design.
 +
**Top white small rectangle is about 3/8 H x 1 1/2 W in inches and located in center of chest just about 1/4 inch below elevated chest area.
 +
**Bottom white long rectangle is spaced about 1/2 inch below top rectangle and is a continuation of the 1 1/2 wide white that runs down to bottom edge of armor.
 +
*Chest and back armor match together at the sides with no open gap.
 +
**A seam line is present.
 +
*Shoulder straps are slotted into the detail ridges of the top connection points.
 +
*Blue areas are weathered with various scuff marks
 +
*Armor is weathered with shades of grey.||}}
-
{{CRLtemplate|File:Clone back.jpg|Back Armor|
+
{{CRLtemplate-nolevels|File:Appo_Ammo_Belt.jpg|Chest Ammo Belt|
-
*Armor should be painted matte or satin white.
+
*Realistic style Chest Ammo Strap with 3 ammo boxes.
-
*Rear tank has detailed area that contains 4 circles. Under the circles at the left side of the back there should be two parallel lines and the the right of the back there should a be a squared detail.
+
**(2) blue ammo boxes placed in top and bottom position along strap.
-
*Chest and back plate should match together at the sides with no gap, just a seam line.  
+
**(1) black ammo box attached between the two blue boxes.
-
*Shoulder straps should be placed underneath the chest to connect to the back. ||
+
**Ammo boxes have black square indented detail near the top and centered.
-
*Shoulder straps should be slotted into the Back into the detail ridges of the top connection points.
+
**Ammo boxes are spaced about 1/2 inch apart.
-
*Highly detailed resin insert should replace softer details.}}
+
*Ammo belt strap is black and about 1 1/2 inch wide. Strap connects to right front of pauldron and extends down behind third belt box on right.||}}
 +
 
 +
{{CRLtemplate-onelevel|File:Appo_Back.jpg|Back Armor|
 +
*Realistic Style back armor.
 +
*Armor is painted matte or satin white.
 +
*Back has a detail plate with four circles on top, two elongated areas on left, and vents on lower right.
 +
*Detail plate is painted blue.
 +
*Back and chest armor match together at the sides with no open gap.
 +
**A seam line is present.
 +
*Shoulder straps are slotted into the detail ridges of the top connection points.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
 +
*Highly detailed resin back box plate cover with circuitry insets.|}}
-
{{CRLtemplate|File:Clone abb.jpg|Ab Armor|
+
{{CRLtemplate-onelevel|File:Abdomen_Phase2_Realistic.jpg|Abdomen Armor|
-
*Armor should be painted matte or satin white.
+
*Realistic style abdomen Armor.
-
*Four 1/4" diameter holes per side on indents of ab plate, eight holes total.
+
*Armor is painted matte or satin white.
-
*Ab section should wrap around the wearers body and be sealed at the sides or at the back.
+
*Eight 1/4" diameter holes, with four holes inside each indented channel of the abdomen.
-
*Ab section should be completely contained under the chest and back armor.||
+
*Abdomen section wraps around the wearers body and is sealed at sides or at back.
-
*Ab section should be seamless at the sides and close in the back.  A detail plate should cover the seam line and hide all work.}}
+
*Abdomen is completely contained under the chest and back armor.
-
 
+
*Armor aligns with codpiece with the seam line hidden by the belt.  
-
{{CRLtemplate|File:CLone cod and rear.jpg|Cod and Posterior Armor|
+
Armor is weathered with shades of grey.|
-
*Armor should be painted matte or satin white.
+
*Seam line along sides or back has no gap.|}}
-
*Cod and Posterior armor should connect at the hips.||
+
-
*Hips should be connected via a snap with the correct detailed shape of the armor at the connection point. }}
+
-
 
+
-
{{CRLtemplate|File:Clone Belt copy.jpg|Belt|
+
-
*Armor should be painted matte or satin white.
+
-
*Ammo Belt with boxes and detonator.
+
-
*Detonator is centered on the back of belt.
+
-
*8 boxes total, 4 on each side of abdomen and attached to the belt.||
+
-
*Belt Boxes should be notched and fitted flush with the details of the belt.
+
-
*Left Rear belt box should have two square buttons in the top left corner and and equal symbol detail at the bottom right.
+
-
*Right Rear belt box should have a bar with two small cylinders centered with and equal symbol detail on the bottom left.
+
-
*From the rear two belt boxes the belt should have a ribbed detailed appearance.}}
+
-
{{CRLtemplate|File:Appo_Comic_Kama.jpg|Kama|
+
{{CRLtemplate-onelevel|File:CLone cod and rear.jpg|Cod and Posterior Armor|
-
*Kama is constructed from a heavy material like canvas or a tight weave burlap.
+
*Realistic style Codpiece and posterior armor.
-
**The Kama should not be lined with matching color fabric.  
+
*Armor is painted matte or satin white.
-
*Kama is a solid black color with matching trim.
+
*Cod and posterior armor connect at the hips.  
-
*The rear of the Kama has a split in the bottom center.  
+
*Armor is weathered with shades of grey.|
-
*Kama is mounted at the start of the front belt boxes.  
+
*Hips have correct detail connector snap and edge feature at the codpiece and posterior side connection.|}}
-
*Kama extends to the bottom of your knee armor.  
+
-
*There are two straps from the kama that connect to a command buckle centered on the front of the belt.||}}
+
{{CRLtemplate|File:501st_Belt.jpg|Belt|
 +
*Realistic style belt, boxes, and detonator.
 +
*Belt, boxes and detonator are painted matte or satin White.
 +
*Belt front, between front boxes, has three vertical rectangle indents which are spaced apart by two protruding rectangle areas.
 +
**The rest of the belt is flat surfaced with raised edging on top and bottom that run along the rest of the belt.  
 +
*Eight Belt Boxes are attached to Belt, with four on each side.
 +
**The two largest Boxes are in front with angled top surface that is higher toward the center.  
 +
**The smallest boxes are located behind the front boxes, about 1/8 inch apart and have an angled end on top.
 +
**The medium sized matching boxes, with flat top cover, are about 1/8 inch from smallest boxes. 
 +
**Left rear box is spaced closer to detonator and has two square buttons in the top left corner, and two dashed indented detail marks on bottom right.
 +
*Right rear box is spaced closer to detonator and has a bar with two small cylinders centered, and two dashed indented detail marks on bottom left.
 +
*A detonator is centered and attached to back of Belt.
 +
**Detonator tube is about 2 1/4 inch diameter with wider detailed end caps.
 +
**Seven horizontally aligned square buttons are on left side of tube, facing backwards.
 +
**Counting from the left side, buttons 1 - 2 - 5 - 6  are painted blue.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
 +
*Boxes are notched on back and fit flush to belt.|
 +
*Back of belt, between rear boxes, has horizontal ribbing.
 +
*Detonator has 1/8 to 1/4 inch wide rectangle base, connecting detonator to Belt.}}
-
{{CRLtemplate|File:Clone thighs.jpg|Thigh Armor|
+
{{CRLtemplate-onelevel|File:Appo_Thighs.jpg|Thigh Armor|
-
*Armor should be painted matte or satin white.  
+
*Realistic style thigh armor.
-
*Front of thigh armor should have a flat triangular area near the knee. From the top of the triangle a ridge line should go up the front of the thigh to the top.
+
*Armor is panted matte or satin white.
-
*Bottom rear of the thigh should have an indentation.
+
*Two parallel vertical blue stripes about 1/2 inch wide each and 3/4 inch apart run down the center of the outside facing side of each thigh.
-
*Armor should be seamless. No visible traces of how the armor was assembled should be shown.||
+
**Front stripe top edge aligns with armor edge and is spaced about 1 1/2 inches below armor edge.
-
*Outside of lower portion of the thighs should come to a point and inner lower end should be rounded.}}
+
**Back stripe top edge aligns with armor edge and is spaced about 1/8 inch below armor edge.
 +
**Both stripes continue down to bottom edge of armor.
 +
**Stripes align with stripes on the lower leg armor.
 +
*Thigh Armor has a flat triangle area above the knee which transitions to a ridge line that runs up the front of the thigh to the top edge.
 +
*Rear of armor has an indented area.
 +
*Armor is seamless.
 +
**No visible traces of how the armor was assembled are shown.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|  
 +
*Outside lower portion of the thighs come to a point and inner lower end is rounded.|}}
-
{{CRLtemplate|File:Clone knees copy.jpg|Knee Armor|
+
{{CRLtemplate-onelevel|File:Legion_Style_Knees_Blue.jpg|Knee Armor|
-
*Armor should be painted matte or satin white.
+
*Realistic style knee armor.
-
*Knees should wrap around the front of the legFrom top center a raised detail line should be present.
+
*Armor is panted matte or satin white.
-
*Knees should be strapped to the leg via a white strap with a raised center area that wraps around the leg and connects on both sides of the Knee.||
+
*Blue stripe edge follows the bottom curve of knee armor with about a 1 1/4 inch widthTop of blue curve pattern creates a white downward point just below elevated vertical rectangle.
-
*Center strap should be primer gray.
+
*Knees have a protruding flat area in front oriented towards the top of Knee.
-
*Connection between the knee and the strapping should have a detail clip.}}
+
*Knees bend around the front and connect to white detail clips that connect the strap on each side.
 +
*A white colored flat strap, about 2 inches wide, wraps around back of leg.
 +
*Blue areas are weathered with various scuff marks.  
 +
*Armor is weathered with shades of grey.|
 +
*Flat Strap has raised 5/8 Inch wide grey center strap.|}}
-
{{CRLtemplate|File:Clone shins.jpg|Lower Leg Armor|
+
{{CRLtemplate-onelevel|File:Appo_Shins.jpg|Lower Leg Armor|
-
*Armor should be painted matte or satin white.
+
*Realistic style lower leg armor.
-
*Lower Legs are mirror images of each other. The front of the armor should have a triangular detail at the top of the leg and a hard ridge line down the front of the shin.
+
*Armor is panted matte or satin white.
-
*Back of the lower legs should have an indentation just under the calf the follow down to the ankle.
+
*Two parallel vertical blue stripes about 1/2 inch wide each and 3/4 inch apart run down the center of the outside facing side of each lower leg armor.
-
*Calf can have an access area on the inside of the leg.  The outside of the calf should be closed.||
+
**Back stripe is aligned with raised point on outside top edge of armor.
-
*Calves should be seamless and have a trap door access through the indent in the rear of the lower leg.
+
**Both stripes run full length of armor from top to bottom edge.
-
*Outside of the lower leg should have a pointed tip at the top and the inside of the lower leg should be rounded off at the top.}}
+
**Stripes align with stripes on the thigh armor.
 +
*Front of lower leg has a flat triangular detail at the top which transitions to a ridge line that travels down the front of the armor to the ankle.
 +
*Back of the lower leg has an indented arched area that continues down to the ankle.
 +
*Bottom of the back side has an arched half circle engraved line at the heel.
 +
*Armor is seamless, except where the calf spoon connects to the back of the lower leg indent edge.
 +
*Blue areas are weathered with various scuff marks.
 +
*Armor is weathered with shades of grey.|
 +
*Calf spoon inserts connect to lower leg inside and are secured to keep in place.|}}
-
{{CRLtemplate|File:Clone shoes copy.jpg |Boots|
+
{{CRL-cloneboots-realistic}}
-
*White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area in armor.
+
-
* Boots must be lace-less and have flat soles.
+
-
*The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
+
-
* This strap shall be white to match the boot.
+
-
*There shall be no markings or labels from the shoe makers. The shoe soles should be gray.||}}
+
{{CRLaccessories}}
{{CRLaccessories}}

Revision as of 13:31, 26 July 2014

crlblackhd.gif
Commander Appo (ROTS Style)
Appo.jpg
Model CC 5298, Photo by Joe P.


Clone-Trooper-Detachment.png

Description: Commander Appo (ROTS Style)
Prefix: CC
Detachment: Clone Trooper Detachment
Context: Expanded universe storyline and Hasbro action figures

Appo wore this version of the armor while serving aboard Vader's Imperator-class Star Destroyer, the "Exactor". Working with Clone Commander Vill, Appo oversaw the removal of Separatist forces from their holdout worlds. Shown here is the Regiment Commander version of Appo's armor, sporting the blue markings of the 501st.


The 501st approval requirements are listed in black.

In the page below, items listed in blue are recommended features that will improve the quality of the costume. Items listed in red are intended to further enhance the finished costume.

For 501st membership only the requirements in black need to be met.

IMPORTANT: The "Animated" armor design, seen in The Clone Wars CG Series, differs from the "Realistic" armor design used to create characters from the theatrical films and graphic novels.
See this thread at clonetroopers.net for the differences between the sculpts.

This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
  • Any uncertainties or questionable aspects of the submitted costume should be brought to the appropriate DL/GML peer review section of the legion forum.
Required Costume Components

The following costume components are present and appear as described below.

Appo Helmet.jpg Helmet
For 501st approval:
  • Realistic style ROTS Phase II helmet.
    • Fan-made helmet.
    • Some "name brand" helmets may be unacceptable.
  • Helmet is painted matte or satin white.
  • Black eye lens.
  • Helmet Mohawk on dome.
  • Helmet has a black brow band, just above the eye lens, that extends around to the back of helmet.
  • Blue stripe runs vertically up front of helmet starting at chin and widens as it continues on top of dome.
  • Helmet frown is charcoal grey in color.
    • Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown.
  • Stripe running up between vocoder and frown is about 1 inch wide.
  • Stripe edges, along center of T lens, are about 3/8 inch wide at bottom and expand to about 5/8 inch near top.
    • Stripe continues above eye lens with about a 3 width and expands upward to align with blue on dome.
    • Stripe above black band is about 3 1/2 inches wide and expands outward to about 4 5/8 inch at front edge of mowhawk.
    • Stripe at center of dome is about 2 3/4 inches from edge of mohawk.
    • Stripe narrows slightly toward back of dome and is about 6 inches wide, and stops short of dome edge leaving about a 3/8 inch white border just above the grey indented band.
  • Black aerators with metal grills are mounted inside the two indented front jaw tubes at base of helmet.
  • Ear caps are dark grey with black edging and detail.
  • (9) dark blue vertical hash marks on each side of helmet cheek.
  • Grey indented helmet band around back of dome.
  • Black Indented vertical rectangle area on back with ribbed detail.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Helmet has an enclosed complete neck ring that seals the helmet to the neck.


Clone trooper neck seal.jpg Neck Seal
For 501st approval:
  • Neck seal is black in color with vertical ribbing or being smooth in appearance.
  • No logos or labels are visible.
    • If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable.



TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


Appo Pauldron.jpg Command Pauldron
For 501st approval:
  • Realistic style Phase II (Episode III) Pauldron.
  • Pauldron has a black leather or vinyl base with wedge shaped panel details.
  • Small black angled shoulder plate is attached to base over right shoulder.
  • Larger angled shoulder plate is attached to base over left sholder and is blue.
  • Ammo strap attaches to front right of pauldron base.


Appo Comic Shoulders.jpg Shoulder Armor
For 501st approval:
  • Realistic style shoulder armor.
  • Shoulders are tear drop in shape with all rounded edges.
  • Armor is painted blue.
  • Armor is weathered with various scuff marks and shades of grey.


Appo Biceps.jpg Upper Arm Armor
For 501st approval:
  • Realistic style Upper Arm Armor.
  • Armor is painted matte or satin white.
  • Armor has a front hard line outside edge and inside rounded edge.
    • Armor piece has a dimple on the lower area of the back of the arm.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
  • Armor is weathered with shades of grey.



Clone elbow copy.jpg Elbow Armor
For 501st approval:
  • Realistic style elbow armor.
  • Armor is painted matte or satin white.
  • Elbow straps have a raised detail line at the top and bottom of the strap.
  • Armor has two parallel dashed detail slots on each outside edge of elbow at the strap connection.
  • Elbows are mirror images of each other with a notched area on the outside of the elbow above the detail marks.
  • Armor is weathered with shades of grey.


Appo Forearms.jpg Forearm Armor
For 501st approval:
  • Realistic style forearm armor.
  • Armor is painted matte or satin white.
  • Wrist end of forearm has a blue stripe, about 3/4 inch wide and spaced about 1/4 from wrist edge, wrapped around the armor.
  • Right forearm has a compad with 8 small buttons,1 large main button, and 1 slightly smaller rectangular button closest to the elbow.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
  • Armor is weathered with various scuff marks and shades of grey.



Clone Hand Guards.jpg Hand Plates
For 501st approval:
  • Realistic style hand plates.
  • Armor is painted matte or satin white
  • Hand plates have a top curving ridge that come to a point over the index or middle finger just past the main knuckle of the hand.
  • Armor is weathered with shades of grey.



Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
  • Gloves cover any exposed skin.
  • Gloves do not show any labels or logos when the armor is worn.


Appo Chest.jpg Chest Armor
For 501st approval:
  • Realistic style Chest Armor.
  • Armor is painted matte or satin white.
  • Two detail slots on lower outside edge of right raised chest area.
  • Armor has blue pillar “A” shape design pattern that runs up the center of chest.
    • Blue pillar design is narrowest at top with about 1 3/4 inch width and widens downward.
  • Design is about 3 1/2 inches wide at the elevated chest edge, and about 6 inches wide at bottom, just above top abdomen edge.
  • Blue pillar design flares outward along bottom edge, about 3 1/2 inches in length, creating about a 3/4 inch blue border on surface that tappers to about 1/2 inch. Blue carries over beveled indented edge along abdomen. Flares end in vertical cut edges.
    • Two white rectangles aligned vertically in center create the “A” shape design.
    • Top white small rectangle is about 3/8 H x 1 1/2 W in inches and located in center of chest just about 1/4 inch below elevated chest area.
    • Bottom white long rectangle is spaced about 1/2 inch below top rectangle and is a continuation of the 1 1/2 wide white that runs down to bottom edge of armor.
  • Chest and back armor match together at the sides with no open gap.
    • A seam line is present.
  • Shoulder straps are slotted into the detail ridges of the top connection points.
  • Blue areas are weathered with various scuff marks
  • Armor is weathered with shades of grey.


Appo Ammo Belt.jpg Chest Ammo Belt
For 501st approval:
  • Realistic style Chest Ammo Strap with 3 ammo boxes.
    • (2) blue ammo boxes placed in top and bottom position along strap.
    • (1) black ammo box attached between the two blue boxes.
    • Ammo boxes have black square indented detail near the top and centered.
    • Ammo boxes are spaced about 1/2 inch apart.
  • Ammo belt strap is black and about 1 1/2 inch wide. Strap connects to right front of pauldron and extends down behind third belt box on right.


Appo Back.jpg Back Armor
For 501st approval:
  • Realistic Style back armor.
  • Armor is painted matte or satin white.
  • Back has a detail plate with four circles on top, two elongated areas on left, and vents on lower right.
  • Detail plate is painted blue.
  • Back and chest armor match together at the sides with no open gap.
    • A seam line is present.
  • Shoulder straps are slotted into the detail ridges of the top connection points.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Highly detailed resin back box plate cover with circuitry insets.
Abdomen Phase2 Realistic.jpg Abdomen Armor
For 501st approval:
  • Realistic style abdomen Armor.
  • Armor is painted matte or satin white.
  • Eight 1/4" diameter holes, with four holes inside each indented channel of the abdomen.
  • Abdomen section wraps around the wearers body and is sealed at sides or at back.
  • Abdomen is completely contained under the chest and back armor.
  • Armor aligns with codpiece with the seam line hidden by the belt.

Armor is weathered with shades of grey.

For level two certification (if applicable):
  • Seam line along sides or back has no gap.
CLone cod and rear.jpg Cod and Posterior Armor
For 501st approval:
  • Realistic style Codpiece and posterior armor.
  • Armor is painted matte or satin white.
  • Cod and posterior armor connect at the hips.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Hips have correct detail connector snap and edge feature at the codpiece and posterior side connection.
501st Belt.jpg Belt
For 501st approval:
  • Realistic style belt, boxes, and detonator.
  • Belt, boxes and detonator are painted matte or satin White.
  • Belt front, between front boxes, has three vertical rectangle indents which are spaced apart by two protruding rectangle areas.
    • The rest of the belt is flat surfaced with raised edging on top and bottom that run along the rest of the belt.
  • Eight Belt Boxes are attached to Belt, with four on each side.
    • The two largest Boxes are in front with angled top surface that is higher toward the center.
    • The smallest boxes are located behind the front boxes, about 1/8 inch apart and have an angled end on top.
    • The medium sized matching boxes, with flat top cover, are about 1/8 inch from smallest boxes.
    • Left rear box is spaced closer to detonator and has two square buttons in the top left corner, and two dashed indented detail marks on bottom right.
  • Right rear box is spaced closer to detonator and has a bar with two small cylinders centered, and two dashed indented detail marks on bottom left.
  • A detonator is centered and attached to back of Belt.
    • Detonator tube is about 2 1/4 inch diameter with wider detailed end caps.
    • Seven horizontally aligned square buttons are on left side of tube, facing backwards.
    • Counting from the left side, buttons 1 - 2 - 5 - 6 are painted blue.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Boxes are notched on back and fit flush to belt.
For level three certification (if applicable):
  • Back of belt, between rear boxes, has horizontal ribbing.
  • Detonator has 1/8 to 1/4 inch wide rectangle base, connecting detonator to Belt.
Appo Thighs.jpg Thigh Armor
For 501st approval:
  • Realistic style thigh armor.
  • Armor is panted matte or satin white.
  • Two parallel vertical blue stripes about 1/2 inch wide each and 3/4 inch apart run down the center of the outside facing side of each thigh.
    • Front stripe top edge aligns with armor edge and is spaced about 1 1/2 inches below armor edge.
    • Back stripe top edge aligns with armor edge and is spaced about 1/8 inch below armor edge.
    • Both stripes continue down to bottom edge of armor.
    • Stripes align with stripes on the lower leg armor.
  • Thigh Armor has a flat triangle area above the knee which transitions to a ridge line that runs up the front of the thigh to the top edge.
  • Rear of armor has an indented area.
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Outside lower portion of the thighs come to a point and inner lower end is rounded.
Legion Style Knees Blue.jpg Knee Armor
For 501st approval:
  • Realistic style knee armor.
  • Armor is panted matte or satin white.
  • Blue stripe edge follows the bottom curve of knee armor with about a 1 1/4 inch width. Top of blue curve pattern creates a white downward point just below elevated vertical rectangle.
  • Knees have a protruding flat area in front oriented towards the top of Knee.
  • Knees bend around the front and connect to white detail clips that connect the strap on each side.
  • A white colored flat strap, about 2 inches wide, wraps around back of leg.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Flat Strap has raised 5/8 Inch wide grey center strap.
Appo Shins.jpg Lower Leg Armor
For 501st approval:
  • Realistic style lower leg armor.
  • Armor is panted matte or satin white.
  • Two parallel vertical blue stripes about 1/2 inch wide each and 3/4 inch apart run down the center of the outside facing side of each lower leg armor.
    • Back stripe is aligned with raised point on outside top edge of armor.
    • Both stripes run full length of armor from top to bottom edge.
    • Stripes align with stripes on the thigh armor.
  • Front of lower leg has a flat triangular detail at the top which transitions to a ridge line that travels down the front of the armor to the ankle.
  • Back of the lower leg has an indented arched area that continues down to the ankle.
  • Bottom of the back side has an arched half circle engraved line at the heel.
  • Armor is seamless, except where the calf spoon connects to the back of the lower leg indent edge.
  • Blue areas are weathered with various scuff marks.
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Calf spoon inserts connect to lower leg inside and are secured to keep in place.


Clone shoes copy.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle.
  • Boots are lace-less.
  • The boots have armor detail to include a natural seam at the toe and a strap that goes over the top of the foot with two protruding disks at each side of the strap.
  • There are no markings or labels from the shoe makers.
  • Boot soles are flat.
  • Boot soles are colored primer grey.


Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.


DC15 carbine.jpg DC-15S Blaster
For 501st approval:

Manufactured by BlasTech Industries the DC-15S is smaller in scale than the DC-15A blaster rifle. Although it has a shorter range than that of the "A" model, it is easier to handle with a higher rate of fire. It features a folding stock for braced firing.

  • Realistic Clone Style DC-15S Blaster.
  • Blaster may be scratch built out of plastic, wood, metal or cast in resin.
  • Blaster has realistic Episode II or Episode III details:
    • Wire frame sight.
    • Folding stock.
    • (12) radiator fins evenly spaced along the length of barrel.
    • Igniter detail knobs.
    • Charge magazine clip on right side.
  • Total length is approximately 26“ (66 cm).
  • Because of the scale, the Hasbro version is incorrect.
For level two certification (if applicable):
  • Charge magazine detail on clip is metal to gun metal grey in color.
  • Detail bolts and screws are metal to gun metal grey in color.
  • Igniter knobs have some copper coloring.
  • Blaster is weathered.
For level three certification (if applicable):
  • Functioning Blue LED is installed in barrel.


DC15 rifle.jpg DC-15A Blaster Rifle
For 501st approval:

Manufactured by BlasTech Industries, the DC-15A is a tibanna gas, cartridge powered weapon. Hyper-ionized blue plasma bolts are more than capable of penetrating armored units. Exceptionally effective against both droids and contemporary targets.

  • Realistic Clone Style DC-15A Blaster Rifle.
  • Blaster rifle is scratch built out of plastic, wood, metal or cast in resin.
  • Blaster has realistic Episode II or Episode III details:
    • Flip up sight in down position.
    • (10) radiator fins evenly spaced along the length of barrel.
    • Power setting adjuster detail lever.
    • Sniper Scope attached under rifle in storage position.
    • Charge magazine clip on left side.
    • Igniter detail knobs.
  • Total length is approximately 55 inches (139.7 cm).
  • Because of the scale, the Hasbro version is not allowed.
For level two certification (if applicable):
  • Charge magazine detail on clip is metal to gun metal grey in color.
  • Detail bolts and screws are metal to gun metal grey in color.
  • Igniter has some copper coloring.
  • Power setting adjuster detail lever is metal or gun metal grey.
  • Sniper scope is metal or gun metal grey.
  • Blaster is weathered.
For level three certification (if applicable):
  • Functioning Blue LED is installed in barrel.

This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:CC_-_Commander_Appo

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.