Costuming:CC - CW-Wolffe - Season 4 - Revision history

Stormtrooperguy at 17:12, 14 May 2012

2012-05-14T17:12:00Z

Stormtrooperguy at 17:10, 14 May 2012

2012-05-14T17:10:46Z

← Older revision		Revision as of 17:10, 14 May 2012
Line 10:		Line 10:
	{{CRLfooter\|CTN_CRL\|C}}		{{CRLfooter\|CTN_CRL\|C}}

-	{{CRLtemplate\|File:S4_wolffe_helmet.jpg\|Helmet\|Wolffe specific Clone Wars style helmet ( modified movie Neyo not acceptable). Helmet painted matte blue-gray with white wolf motif on each side. Weathering should be shades of grey. Red triangle above the brow with 3 yellow 'kill' stripes on either side. RF stalk mounted on the outside of the ear, with a gray RF topper }}	+	{{CRLtemplate\|File:S4_wolffe_helmet.jpg\|Helmet\|
		+	*Wolffe specific Clone Wars style helmet ( modified movie Neyo not acceptable).
		+	*Helmet painted matte blue-gray with white wolf motif on each side.
		+	*Weathering should be shades of grey.
		+	*Red triangle above the brow with 3 yellow 'kill' stripes on either side.
		+	*RF stalk mounted on the outside of the ear, with a gray RF topper\|\| }}

	{{CRL-TC_animated_neckseal}}		{{CRL-TC_animated_neckseal}}

Darren1970 at 16:41, 14 May 2012

2012-05-14T16:41:07Z

← Older revision		Revision as of 16:41, 14 May 2012
Line 110:		Line 110:
	*The edge of the sole should be flat and have notches cut into it.		*The edge of the sole should be flat and have notches cut into it.
	*A detail strap should be placed over the top of each boot. \|}}		*A detail strap should be placed over the top of each boot. \|}}
		+
		+	{{CRLdc17pistol-animated}}

Darren1970 at 19:46, 13 May 2012

2012-05-13T19:46:57Z

← Older revision		Revision as of 19:46, 13 May 2012
Line 94:		Line 94:
	*The edge of the kama should be trimmed in gray. \|}}		*The edge of the kama should be trimmed in gray. \|}}

		+	{{CRLtemplate\|File:S4_wolffe_holsters.jpg\|Holsters\|
		+	* Holsters should be painted matte or satin white. If weathered the weathering should eb shades of gray.
		+	*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. \|}}

	{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|		{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|

Darren1970 at 19:35, 13 May 2012

2012-05-13T19:35:41Z

← Older revision		Revision as of 19:35, 13 May 2012
Line 88:		Line 88:
	* Armor must be seamless. No visible traces of how the armor was assembled should be shown. \|		* Armor must be seamless. No visible traces of how the armor was assembled should be shown. \|
	* Armor must be weathered.\|}}		* Armor must be weathered.\|}}
		+
		+	{{CRLtemplate\|File:S4_wolffe_kama.jpg\|Kama\|
		+	* The kama must be made of black suede-ette material, or heavy canvas.
		+	*The kama should be 2 seperate sections with rounded corners.
		+	*The edge of the kama should be trimmed in gray. \|}}
		+

	{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|		{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|
Line 96:		Line 102:
	* Outer seam of the shin must be seamless. A clamshell opening on the inner seam is acceptable. \|		* Outer seam of the shin must be seamless. A clamshell opening on the inner seam is acceptable. \|
	* Armor must be weathered.\|}}		* Armor must be weathered.\|}}
		+
		+	{{CRLtemplate\|File:S4_wolffe_shoes.jpg\|Boots\|
		+	* The shoes should be blue-gray in colour.
		+	*The edge of the sole should be flat and have notches cut into it.
		+	*A detail strap should be placed over the top of each boot. \|}}

Darren1970 at 19:18, 13 May 2012

2012-05-13T19:18:54Z

← Older revision		Revision as of 19:18, 13 May 2012
Line 87:		Line 87:
	*The rear of the thigh should have an indentation.		*The rear of the thigh should have an indentation.
	* Armor must be seamless. No visible traces of how the armor was assembled should be shown. \|		* Armor must be seamless. No visible traces of how the armor was assembled should be shown. \|
		+	* Armor must be weathered.\|}}
		+
		+	{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|
		+	* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
		+	* Lower shins have blue-gray jagged paint scheme as shown.
		+	*Knee armor is integrated with the lower leg.
		+	*The rear of the shin should have an indentation.
		+	* Outer seam of the shin must be seamless. A clamshell opening on the inner seam is acceptable. \|
	* Armor must be weathered.\|}}		* Armor must be weathered.\|}}

Darren1970 at 13:19, 13 May 2012

2012-05-13T13:19:15Z

← Older revision		Revision as of 13:19, 13 May 2012
Line 80:		Line 80:
	*Detonator is centered on the back of belt with no control buttons. The detonator has 2 lines set in approx 1/2" - 5/8" from the edges. Lines may be recessed or painted on. \|		*Detonator is centered on the back of belt with no control buttons. The detonator has 2 lines set in approx 1/2" - 5/8" from the edges. Lines may be recessed or painted on. \|
	*Armor must be weathered. \| }}		*Armor must be weathered. \| }}
		+
		+	{{CRLtemplate\|File:S4_wolffe_thighs.jpg\|Thigh Armor\|
		+	* Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
		+	* Front of thigh armor should have a flat triangular area near the knee with a notch cut out for the knee armor. From the top of the triangle a ridge line should go up the front of the thigh to the top.
		+	*The upper outer edge should have an angled section.
		+	*The rear of the thigh should have an indentation.
		+	* Armor must be seamless. No visible traces of how the armor was assembled should be shown. \|
		+	* Armor must be weathered.\|}}

Darren1970 at 12:22, 13 May 2012

2012-05-13T12:22:19Z

← Older revision		Revision as of 12:22, 13 May 2012
Line 64:		Line 64:
	*The ab armour joins at the rear and the join is covered by a plate.		*The ab armour joins at the rear and the join is covered by a plate.
	. \|		. \|
		+	*Armor must be weathered. \| }}
		+
		+	{{CRLtemplate\|File:S4_wolffe_cod.jpg\|Codpiece and belt front\|
		+	*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
		+	* Belt is approx 3" tall and divided into segments. The front segments have a key/slot detail.
		+	*Belt boxes are mounted forwards, leaving 2 segments clear at the front.
		+	*Cod and Posterior armor should connect at the hips. \|
		+	*Armor must be weathered. \| }}
		+
		+	{{CRLtemplate\|File:S4_wolffe_but.jpg\|Posterior Armor, belt rear and detonator
		+	\|
		+	*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
		+	* Belt is approx 3" tall and divided into segments.
		+	*Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.
		+	*Detonator is centered on the back of belt with no control buttons. The detonator has 2 lines set in approx 1/2" - 5/8" from the edges. Lines may be recessed or painted on. \|
	*Armor must be weathered. \| }}		*Armor must be weathered. \| }}

Darren1970 at 12:07, 13 May 2012

2012-05-13T12:07:29Z

← Older revision		Revision as of 12:07, 13 May 2012
Line 56:		Line 56:
	*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.		*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
	*Shoulder straps fit into the tops of the chest and back. \|		*Shoulder straps fit into the tops of the chest and back. \|
		+	*Armor must be weathered. \| }}
		+
		+	{{CRLtemplate\|File:S4_wolffe_abs.jpg\|Ab Armor\|
		+	*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
		+	* Top edge of the armour is squared off to match the chest armor.
		+	*The ab armour protrudes out in the middle to batter match the chest.
		+	*The ab armour joins at the rear and the join is covered by a plate.
		+	. \|
	*Armor must be weathered. \| }}		*Armor must be weathered. \| }}

Darren1970 at 12:03, 13 May 2012

2012-05-13T12:03:03Z

← Older revision		Revision as of 12:03, 13 May 2012
Line 48:		Line 48:
	*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.		*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
	*Shoulder straps fit into the tops of the chest and back \|		*Shoulder straps fit into the tops of the chest and back \|
		+	*Armor must be weathered. \| }}
		+
		+	{{CRLtemplate\|File:S4_wolffe_back.jpg\|Back Armor\|
		+	*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
		+	* Top section of the backplate has blue-gray section extending down to the detail plate - as shown.
		+	*Backplate has a detail plate, similar to movie clonetroopers, as shown.
		+	*Chest and back plate must match together at the sides and shoulders with no gap. Butted seam lines are permitted if required.
		+	*Shoulder straps fit into the tops of the chest and back. \|
	*Armor must be weathered. \| }}		*Armor must be weathered. \| }}

← Older revision		Revision as of 19:46, 13 May 2012
Line 94:		Line 94:
	*The edge of the kama should be trimmed in gray. \|}}		*The edge of the kama should be trimmed in gray. \|}}

		+	{{CRLtemplate\|File:S4_wolffe_holsters.jpg\|Holsters\|
		+	* Holsters should be painted matte or satin white. If weathered the weathering should eb shades of gray.
		+	*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. \|}}

	{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|		{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|

← Older revision		Revision as of 19:35, 13 May 2012
Line 88:		Line 88:
	* Armor must be seamless. No visible traces of how the armor was assembled should be shown. \|		* Armor must be seamless. No visible traces of how the armor was assembled should be shown. \|
	* Armor must be weathered.\|}}		* Armor must be weathered.\|}}
		+
		+	{{CRLtemplate\|File:S4_wolffe_kama.jpg\|Kama\|
		+	* The kama must be made of black suede-ette material, or heavy canvas.
		+	*The kama should be 2 seperate sections with rounded corners.
		+	*The edge of the kama should be trimmed in gray. \|}}
		+

	{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|		{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|
Line 96:		Line 102:
	* Outer seam of the shin must be seamless. A clamshell opening on the inner seam is acceptable. \|		* Outer seam of the shin must be seamless. A clamshell opening on the inner seam is acceptable. \|
	* Armor must be weathered.\|}}		* Armor must be weathered.\|}}
		+
		+	{{CRLtemplate\|File:S4_wolffe_shoes.jpg\|Boots\|
		+	* The shoes should be blue-gray in colour.
		+	*The edge of the sole should be flat and have notches cut into it.
		+	*A detail strap should be placed over the top of each boot. \|}}

← Older revision		Revision as of 17:12, 14 May 2012
Line 78:		Line 78:
	*Armor must be weathered. \| }}		*Armor must be weathered. \| }}

-	{{CRLtemplate\|File:S4_wolffe_but.jpg\|Posterior Armor, belt rear and detonator	+	{{CRLtemplate\|File:S4_wolffe_but.jpg\|Posterior Armor, belt rear and detonator\|
-	\|	+
	*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.		*Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
	* Belt is approx 3" tall and divided into segments.		* Belt is approx 3" tall and divided into segments.
	*Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.		*Cod and Posterior armor should connect at the hips. Butted seams are permitted at this connection if required.
	*Detonator is centered on the back of belt with no control buttons. The detonator has 2 lines set in approx 1/2" - 5/8" from the edges. Lines may be recessed or painted on. \|		*Detonator is centered on the back of belt with no control buttons. The detonator has 2 lines set in approx 1/2" - 5/8" from the edges. Lines may be recessed or painted on. \|
-	*Armor must be weathered. \| }}	+	*Armor must be weathered. \|\| }}

	{{CRLtemplate\|File:S4_wolffe_thighs.jpg\|Thigh Armor\|		{{CRLtemplate\|File:S4_wolffe_thighs.jpg\|Thigh Armor\|
Line 92:		Line 91:
	*The rear of the thigh should have an indentation.		*The rear of the thigh should have an indentation.
	* Armor must be seamless. No visible traces of how the armor was assembled should be shown. \|		* Armor must be seamless. No visible traces of how the armor was assembled should be shown. \|
-	* Armor must be weathered.\|}}	+	* Armor must be weathered.\|\|}}

	{{CRLtemplate\|File:S4_wolffe_kama.jpg\|Kama\|		{{CRLtemplate\|File:S4_wolffe_kama.jpg\|Kama\|
	* The kama must be made of black suede-ette material, or heavy canvas.		* The kama must be made of black suede-ette material, or heavy canvas.
	*The kama should be 2 seperate sections with rounded corners.		*The kama should be 2 seperate sections with rounded corners.
-	*The edge of the kama should be trimmed in gray. \|}}	+	*The edge of the kama should be trimmed in gray. \|\|}}

	{{CRLtemplate\|File:S4_wolffe_holsters.jpg\|Holsters\|		{{CRLtemplate\|File:S4_wolffe_holsters.jpg\|Holsters\|
	* Holsters should be painted matte or satin white. If weathered the weathering should eb shades of gray.		* Holsters should be painted matte or satin white. If weathered the weathering should eb shades of gray.
-	*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. \|}}	+	*Holsters may connect to the belt via straps or directly to the kama with no visible attachment. \|\|}}

	{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|		{{CRLtemplate\|File:S4_wolffe_shins.jpg\|Shin Armor\|
Line 114:		Line 113:
	* The shoes should be blue-gray in colour.		* The shoes should be blue-gray in colour.
	*The edge of the sole should be flat and have notches cut into it.		*The edge of the sole should be flat and have notches cut into it.
-	*A detail strap should be placed over the top of each boot. \|}}	+	*A detail strap should be placed over the top of each boot. \|\|}}

	{{CRLdc17pistol-animated}}		{{CRLdc17pistol-animated}}