crlblackhd.gif
Jango Fett
BH AOTC Jango Fett.jpg
Model BH 412, Photo by Arturo Delgado


Bounty-Hunters-Guild.png

Description: Jango Fett
Prefix: BH
Detachment: Bounty Hunters Guild
Context: Star Wars Episode II: Attack of the Clones
Jango Fett is the genetic "father" to Boba Fett and all of the clone troopers.

For additional information on Jango Fett costuming, visit the discussion board at The Dented Helmet and check out their Jango Fett reference gallery


The 501st approval requirements are listed in black.

The Bounty Hunters' Guild defines two additional, optional levels of costuming excellence. In the page below, requirements for Level 1 "Notorious" are listed in blue. Level 2 "Infamous" requirements are in red. Please visit the BHG web site for a full description of these standards.

For 501st membership only the requirements in black need to be met.

This Visual Guide has been reviewed by the detachment staff and the LMO team and is certified for use as a minimum approval guideline for GMLs. GMLs are free to approve this costume type.
  • Any uncertainties or questionable aspects of the submitted costume should be brought to the appropriate DL/GML peer review section of the legion forum.
Required Costume Components

The following costume components are present and appear as described below.

BH jango helmet front.jpg Helmet
For 501st approval:
  • Helmet has a dark colored, full one piece "T" visor.
  • Helmet has a rangefinder and stalk on the right side.
  • The mandibles and head band are a medium blue color.
  • The upper cheeks, ear pieces and rangefinder are a darker blue color.
    • Both blues match the visual references as closely as possible in similar lighting.
  • The dome, lower cheeks, key slot area and the back of the helmet are silver in color.
  • The helmet is weathered to match the visual references as closely as possible.  
  • (2) 1/8 inch parallel strips extend around the dome, just above the blue band, and stop on either side of the right earpiece attachment.
    • Auto pin-striping is recommended.
  • The keyhole slots in the rear of helmet are cut out clean and backed with dark mesh, fabric or screening underneath.
  • The ear cap on the rangefinder side of the helmet is attached so that it almost closes the gap between the top and bottom half and so that it sits lower than the piece that's formed into the helmet itself.
For level two certification (if applicable):
  • A dark gray or slate blue, vinyl or leather gasket attaches underneath and inside the helmet sealing it to the neck.
  • The silver cheeks are rounded at the top, unlike the more tapered cheeks of Boba Fett.
For level three certification (if applicable):
  • A servo motor attached to the inside of the helmet motorizes the rangefinder to arc 90 degrees.
BH jango flightsuit.jpg Flightsuit
For 501st approval:
  • Flightsuit is light blue-purple or slate blue in color.
  • Flightsuit is double sleeved with long inner sleeves going under the forearm gauntlets and the shorter outer sleeves stopping just above the elbow.
  • The seams of both sleeves run in a frontal line from the shoulder, down the bicep and forearm.
  • Knee and Lower Leg Armor attach to the legs.
    • Hook and loop fastener or snaps are recommended.
  • Pants do not droop over the boots and tighten up around the knees and ankles.
For level two certification (if applicable):
  • Flightsuit has button holes on either side of the knee to allow for knee straps to go through and secure inside the pants.
BH jango vest.jpg Flak Vest
For 501st approval:
  • Vest is charcoal grey or dark bluish grey in color.
  • Vest is made of leather or similar material.
  • Vest allows for the attachment of chest, back, belly, shoulder and collar armor.
  • Vest closes down the left side and on the left shoulder.
  • Vest has piping on the seams of the neck, shoulder and arm openings.
  • Shoulders do not flare outward like wings.
  • Back of vest has cut slits to allow the Jetpack harness straps to feed through.
  • Vest is long enough to be worn under the girth belt.


BH jango shoulder bells.jpg Shoulder Armor
For 501st approval:
  • Armor is made of a solid material such as fiberglass, styrene or sintra.
  • Armor has dimension giving the feeling of thickness and depth.
  • Armor is silver in color and weathered where indicated in visual references to give the illusion of battle wear and damage.
  • Shoulder Armor has eight points and curves around the upper arm.
  • Armor attaches securely to the shoulders of the vest.


BH jango gauntlets.jpg Gauntlets
For 501st approval:
  • Gauntlets arehinged on the inside of the forearm and close on the outside with hook and loop fastener, or similar attachment.
  • Gauntlets are made of a solid material such as fiberglass, resin or styrene.
  • Gauntlets are silver in color and weathered where indicated in visual references to give the illusion of battle wear and damage.
  • Gauntlets have five blue hoses weathered to match visual references as closely as possible.
    • Three on the right, two on the left.
  • All five hoses are tucked under the short sleeve of the flightsuit and attached securely.
  • The right gauntlet contains the following components as shown in visual references:
    • Two toggle switches on upper inside section.
    • Four forward facing darts in front of middle section.
    • Two small slightly protruding darts in front of lower section (over wrist opening).
    • Larger grappling dart with three "blades" protruding from side housing
    • Two hose connecters at rear of housing and an upper tapering section with a third hose connector.
  • The right gauntlet has four square pattern indentations on lower section as shown in visual reference.
  • The left gauntlet has a rocket securely attached.
  • Left gauntlet has black and silver parallel bands in alternating pattern running the length of the missile.
  • The rear cylinder is black in color and the front tapered section is gold with a black point as shown in the visual references.
    • The tip of the black point is gold in color.
  • The construction of the left gauntlet includes the following details:
    • A small silver and black switch on the inside of the section holding the rocket.
    • A working red LED light behind this switch.
    • Two black buttons sitting on top of the flamethrower assembly on the outside of the gauntlet.
    • Two vertically stacked nozzles that protrude from the front of the flamethrower assembly.
    • Two hose connectors at the rear of the flamethrower assembly.
  • Three square pattern indentations on the lower gauntlet section as show in visual references.


BH jango gloves.jpg Gloves
For 501st approval:
  • Gloves are navy-blue in color.
  • Gloves are made of a thin, soft leather or similar material.
  • Gloves are worn tucked underneath the gauntlets.


BH jango chest armor.jpg Chest Armor
For 501st approval:
  • Consists of collar armor, left and right breast plates, a center diamond and an abdominal plate.
  • Armor is made of a solid material such as fiberglass, styrene or sintra.
  • Armor has dimension giving the feeling of thickness and depth.
  • Armor is silver in color and weathered where indicated in visual references to give the illusion of battle wear and damage.
  • Left breast plate has two indented horizontal bars.
    • The lower one to be wider and positioned as shown in visual references.
  • Center diamond plate between breast plates has an indented vertical rectangle as shown in visual references.
  • Chest Armor attaches securely to the front of the vest.


BH jango back armor.jpg Back Armor
For 501st approval:
  • Armor is made of a solid material such as fiberglass, styrene or sintra.
  • Armor has dimension giving the feeling of thickness and depth.
  • Armor is silver in color and weathered where indicated in visual references to give the illusion of battle wear and damage.
  • Back Armor has two rectangular slots, over the shoulder blades, to allow for the Jetpack straps to feed through.
  • Back Armor attaches securely to the back of the vest.


BH jango jetpack.jpg Jetpack
For 501st approval:
  • Jetpack options include the "standard pack", or the "arena pack".
  • The stndard colors for the jetpack are: medium blue, silver, white, black, yellow-orange, and red.
  • Jetpack has the following main components:
    • One center tank and two side fuel tanks,.
    • "Piano keys" stretching horizontally at the top of the main body on each side of the center raised strip.
  • One center missile.
    • Two side mounted thrusters / nozzles.
    • One beacon light and one stabilizer.
  • Jetpack attaches snugly against the Back Armor via two black shoulder straps which exit the Back Armor through two slots located near the shoulder blades.
  • All patterns, colors and weathering match visual references as closely as possible.
  • Lettering symbols and pin-striping (either hand painted or decals) match visual references as closely as possible.
For level two certification (if applicable):
  • Jetpack beacon is illuminated with a white light.
  • Jetpack attaches to the harness via two black plastic clips that exit the rear of the Jetpack.
BH jango arena pack.jpg Arena Pack
For 501st approval:
  • Jetpack options include the "arena pack", or the "standard pack".
  • The colors for the arena pack are: silver, dark blue and light blue.
  • In place of the larger rocket found on the standard jetpack, the arena pack has a smaller cone shaped missile.
  • The thrusters are located under the fuel tanks.
  • Jetpack attaches snugly against the Back Armor via two black shoulder straps which exit the Back Armor through two slots located near the shoulder blades.
  • All patterns, colors and weathering match visual references as closely as possible.


BH jango bollero belt.jpg Girth Belt
For 501st approval:
  • Girth Belt is made of leather or similar materials.
  • Belt is brown in color.
  • Girth Belt is made of horizontal rows of 1/4" braid and is approximately 5" wide.
    • Depending on the height of the person.
    • Typically (20) to (22) rows of braids constitutes the average size girth belt.
  • Belt attaches in rear.
    • Heavy duty hook and loop fastener or lacing is recommended for durability.
  • Girth Belt has a vertical brown leather loop, approximately three inches wide, covering the rear overlapping belt seam.


BH jango ammo belt.jpg Ammo Belt
For 501st approval:
  • Ammo Belt is made of leather or a similar sturdy material.
  • Belt is brown in color.

Ammo Belt is approximately 2.5 inches wide.

    • The end of belt is tapered and overlaps the other end in rear.
    • Hook and loop fastener (or similar) attachment is recommended.
  • Ammo Belt includes seven equally sized pouches, approximately 2.5 inches wide and 4.5 inches tall, attached to belt by loops.
  • A separate vertical loop, approximately 3/4 inches wide, fits over the belt to the wearer's left against the left most pouch.
  • Ammo Belt attaches in rear, over the braided belt, and the vertical leather loop.


BH jango codpiece.jpg Codpiece
For 501st approval:
  • Armor is made of a solid material such as fiberglass, styrene or sintra.
  • Armor has dimension giving the feeling of thickness and depth.
  • Armor is silver in color and weathered where indicated in visual references to give the illusion of battle wear and damage.
  • Codpiece is worn under all of the belts.


BH jango thigh armor.jpg Thigh Armor
For 501st approval:
  • Armor is made of a solid material such as fiberglass, styrene or sintra.
  • Armor has dimension giving the feeling of thickness and depth.
  • Armor is curved to fit snugly over thighs.
  • Armor is silver in color and weathered where indicated in visual references to give the illusion of battle wear and damage.
  • Thigh Armor attaches securely on the thighs of the flightsuit.


BH jango holsters.jpg Holsters
For 501st approval:
  • Holsters are made of leather or similar sturdy material.
  • Holsters are brown in color.
  • Straps are approximately 1" inch wide and fastened underneath the rear of girth belt and through an angled loop on front, which sits on the Codpiece armor via two brass D rings and a leather (or vinyl) strip, which inserts into the armor loop.
  • Straps are adjustable with 1/4 inch brass ball studs.
    • Six studs in total are used.
    • Two for rear straps, two for front straps and two more for leg straps.
  • The shape of the holster matches the general shape of the blasters.
    • The opening at the top is angled and slightly flared.
    • The bottoms are tapered so that the blasters fit snugly.


BH jango knee armor.jpg Knee Armor
For 501st approval:
  • Armor is made of a solid material such as fiberglass, styrene or sintra.
  • Armor has dimension giving the feeling of thickness and depth.
  • Armor is silver in color and weathered where indicated in visual references to give the illusion of battle wear and damage.
  • Knee Armor has (2) silver colored darts on the outer side of each knee.
  • Inner section has an upside down "F shaped pattern".
For level two certification (if applicable):
  • Knee Armor attaches securely to the front of the knees over the flightsuit using black nylon straps that enter the sides of the flightsuit, through button holes in the suit.
BH jango shin armor.jpg Lower Leg Armor
For 501st approval:
  • Armor is made of a solid material such as fiberglass, styrene or sintra.
  • Armor has dimension giving the feeling of thickness and depth.
  • Armor is silver in color and weathered where indicated in visual references to give the illusion of battle wear and damage.

Lower Leg Armor attaches securely to the front of the shins over the flightsuit.


BH jango boot armor.jpg Foot Armor (Boot Caps)
For 501st approval:
  • Armor is made of a solid material such as fiberglass, styrene or sintra.
  • Armor has dimension giving the feeling of thickness and depth.
  • Armor is silver in color and weathered where indicated in visual references to give the illusion of battle wear and damage.
  • Foot Armor is worn securely on top of the boots and have black nylon straps that snap on each side of the boot's heals.


BH jango boot.jpg Boots
For 501st approval:
  • Boots are made of black leather.
  • Boot sole pattern matches, as closely as possible, to the movie costume.
    • Most identifiable features include a high arch pattern on the inside of the sole.
    • Four profile "swoops" between the sole and leather upper which is silver in color.
  • Boots allow for secure attachment of Foot Armor on top of boot.
For level two certification (if applicable):
  • Boots have snaps attached to the sides of the heel area to allow the attachment of the Foot Armor straps.
For level three certification (if applicable):
  • Film Accurate boots are "Kenneth Cole Pit Crew".
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present appear as described below.

Westars.jpg Westar 34s
For 501st approval:
  • Based on a scratch-built or a modified commercial toy Westar 34 pistol.
  • Pistols are silver or chrome in color with a matte finish on the handles.
For level two certification (if applicable):
  • Pistols are machined metal and chrome plated.

Versions française

S'il vous plaît voir les lien ci-dessous pour le français des version traduites.


This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.