|
| Dengar
|
|
Model Model, Photo by Photographer
|
|
|
|
The 501st approval requirements are listed in black.
The Bounty Hunters' Guild defines two additional, optional levels of costuming excellence. In the page below, requirements for Level 1 "Notorious" are listed in blue. Level 2 "Infamous" requirements are in red. Please visit the BHG web site for a full description of these standards.
For 501st membership only the requirements in black need to be met.
|
|
|
- This CRL is a work in progress. This costume may be approved by GMLs, but additional research should be done until the CRL is complete.
- If you have this costume and would like to assist with this CRL, please contact your detachment leader!
- Please note that the use of the word "should" below does not indicate that a requirement is optional. All instances of should will be replaced with must as this guide is completed.
|
| Required Costume Components
|
|
The following costume components must be present and appear as described below for approval .
|
|
|
| Head Wraps
For 501st approval:
- The head wrap should be an open mesh, cheesecloth, gauze-like material that replicates a fresh bandage.
- Bandage should be clean of weathering.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Hood
For 501st approval:
- Light gray close fitting Balacalva style hood with a loose neck/chin cover.
|
For level two certification (if applicable):
- Chin cover: Three weathered snaps on each side. Two caps and one male snap.
|
For level three certification (if applicable):
- The center male snaps are to be centered and brought in ¾” from the capped snaps
|
|
|
|
| Facial Features
For 501st approval:
- Make-up drawn on face to replicate the scar
|
For level two certification (if applicable):
- Scarring make-up or prothstetics used to replicate the scar. Ex. rigid collodion scarring liquid
|
For level three certification (if applicable):
- Eyebrows are covered by latex stage make-up or shaved off.
|
|
|
|
| Shoulder Bells
For 501st approval:
- Stormtrooper Bells are used
- One on each side and held together by a webbing strap that is worn across the back of the shoulders.
|
For level two certification (if applicable):
- An elastic strap keeps the bell close to the arm
|
For level three certification (if applicable):
- A 3” “armour scar” is on the backside of the right Shoulder Bell.
|
|
|
|
| Forearms
For 501st approval:
- Stormtrooper forearm pieces are used.
- Forearm pieces are assembled and cut open lengthwise on the plain bottom half of the forearm.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Gloves
For 501st approval:
- Gray or White leather gloves with a 4-6 inch cuff. The brand name WELDAS SOFTOUCH Tig/Mig gloves appear to be the closest to the screen used gloves.
- White Damascus D650 Gauntlets or White/Grey Fencing gloves are a perfectly acceptable alternative.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Chest Armour
For 501st approval:
- A Snow trooper Chest plate and ribbed shoulder straps are used.
- Upper Center Greeblie plate should have two round buttons , a vent piece, two bushings and two off-centered, blocks.
- “T” Greeblie as seen on the snowtrooper chest.
- Lower Center Greeblie is a comm pad placed in the void of the snowtrooper chest plate
- A three button plate is on the left.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
- The Comm Pad is curved
- A webbing strap is attached underneath the ribbed, plastic strap via a Chicago screw on the front and is attached to the backpack by two split rivets
- Square greeblies as seen on the scout trooper helmet mouth area are seen on the lower corners of the chest armour.
|
|
|
|
| Ab/Cod Piece
For 501st approval:
- Sandtrooper Ab Plate is used.
- Left side ab plate has only 3 buttons. Not four.
- Right side ab plate is blank and does not contain buttons like the Stormtrooper
- There is a strap that attaches from the end of the cod piece to the back side of the belt.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
- There is an “armour scar” on the lower left side of the cod piece
|
|
|
|
| Belt and Pouches
For 501st approval:
- Belt is 2 inches wide and can be made of cloth, nylon strap or leather.
- Pouches are rectangular and boxy with an angled flap.
- Pouches secure to belt through a continuous loop on the back of each pouch.
|
For level two certification (if applicable):
- Pouches have two 1” loops
- Belt buckle has a round disk in the center
|
For level three certification (if applicable):
|
|
|
|
| Sidearm holster
For 501st approval:
- Leather or leather-like material.
- Attaches to belt like a Hoth Rebel Trooper or directly to the the thigh armor.
|
For level two certification (if applicable):
|
For level three certification (if applicable):
|
|
|
|
| Thigh Armor
For 501st approval:
- Stormtrooper thighs are used.
- It is suggested for trooping purposes that a hidden garter belt under the jumpsuit or armour is attached to the jumpsuit by way of snaps or other method is best
- The thigh armour is closed in the back.
|
For level two certification (if applicable):
- A wide shim of plastic that is similar to armour is to help close the back seam.
|
For level three certification (if applicable):
- A 1” elastic strap is attached by two split rivets at the top of the front thigh pieces which wraps around the entire leg.
|
|
|
|
| Greaves
For 501st approval:
- Sandtrooper Greaves are used for BOTH legs
- Greaves open in the back to expose the boot. Greaves should not close in the back.
- Diamond Knee plates – six sided (hexagon) mounted onto a five-sided “diamond” shape, with a point on the bottom – are on the wearer’s left and right knees
- There are three 1 ¼ ” straps surrounding the circumference of the greaves.
- Straps loosely hang off and droop
|
For level two certification (if applicable):
- Straps are made of canvas
|
For level three certification (if applicable):
- Straps are made from web belt material
|
|
|
|
| Boots
For 501st approval:
- Light tan or gray moccasin style, calf length boot
|
For level two certification (if applicable):
- Weathered suede or rough leather
|
For level three certification (if applicable):
|
|
|
|
NAVIGATION
|
