(Difference between revisions)
Line 1: Line 1:
-
{{CRLheader|Cad Bane in Denal Disguise|File:jpg||}}
+
{{CRLheader|Cad Bane in Denal Disguise|File:Missingprofile.jpg||}}

Revision as of 04:40, 30 May 2014

crlblackhd.gif
Cad Bane in Denal Disguise
Missingprofile.jpg
Model ', Photo by '


Bounty-Hunters-Guild.png

Description: Cad Bane in Clone Trooper Denal disguise
Prefix: BH
Detachment: Bounty Hunters Guild
Context: The Clone Wars, seasons .
{{{5}}}


The 501st approval requirements are listed in black.

The Bounty Hunters' Guild defines two additional, optional levels of costuming excellence. In the page below, requirements for Level 1 "Notorious" are listed in blue. Level 2 "Infamous" requirements are in red. Please visit the BHG web site for a full description of these standards.

For 501st membership only the requirements in black need to be met.

  • This CRL is a work in progress.
  • As such, this costume must be approved by the Legion Membership Officer, via the appropriate section of the Legion forum.
  • If you have this costume and would like to assist with the completion of this library entry, please contact your detachment leader.
  • Please note that the use of the word "should" below does not indicate that the armor piece is considered open to interpretation. All instances of "should be" and "should have" will be replaced with "is" and "has", as this guide is completed.

Required Costume Components

The following costume components are present and appear as described below.

Cad Bane mask.jpg Mask
For 501st approval:
  • The mask must be a high quality representation of the reference images made of silicon, latex or other flesh like material.

For level two certification (if applicable):
For level three certification (if applicable):


TC animated neckseal.jpg Neck Seal
For 501st approval:
  • Neck seal is black in color with no ribbing.
  • No logos or labels are visible.
    • If the seal is not incorporated as part of the under suit, a balaclava or other similar covering is acceptable.
For level two certification (if applicable):
  • Neck seal closes in the front via 2 small black snaps.


TK anh stunt undersuit.jpeg Under Suit
For 501st approval:
  • Black non-textured material, either one-piece or two-piece construction with no visible zippers or logos.


150px Shoulder Bells
For 501st approval:
  • Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
  • Armor must have a blue stripe down the center.
  • Shoulders should be padded so as not to sit flat against the arms. The top of the bell should sit 3/4" - 1" above the natural shoulder.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):
Denal bicep.jpg Upper Arm Armor
For 501st approval:
  • Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
  • Armor must have a blue stripe down the center that lines up with the shoulder.
  • Armor has a notch on the lower area of the back of the arm that matches up with the elbow armor.
  • Armor must be seamless. No visible traces of how the armor was assembled should be shown.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):
Denal forearms.jpg Forearm Armor
For 501st approval:
  • Armor must be painted matte or satin white. If weathered, the weathering should be shades of grey.
  • Armor must have a blue stripe down the center.
  • Left forearm must have a compad that has 4 main square recessed areas and 1 slightly smaller square recessed area. The smaller recess is closest to the elbow.
  • Armor must be seamless on the outside edge. Due to the shape of the armor, a butted seam is acceptable on the inside if required.
  • Elbow plate is integrated into the forearm, extending up to fit into the notch on the bicep.
  • Elbow plate is divided in half: Blue on the outer half, white on the inner (relative to the wearer's torso)
For level two certification (if applicable):
  • Armor must be seamless. No visible traces of how the armor was assembled should be shown.
  • Armor must be weathered.
For level three certification (if applicable):
Denal handplates.jpg Hand Plates
For 501st approval:
  • Armor must be painted blue. If weathered, the weathering should be shades of grey.
  • Hand plates are mirror images of each other.
For level two certification (if applicable):
  • Armor must be weathered.
For level three certification (if applicable):


Generic-black-gloves.jpg Gloves
For 501st approval:
  • Black over the wrist gloves made of leather, nylon, or other low pile fabrics.
  • Gloves cover any exposed skin.
  • Gloves do not show any labels or logos when the armor is worn.



TC animated chest.jpg Chest Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Lower portion of the chest has a curved notch for the abdomen armor to fit into.
  • Chest and back plate match together at the sides and shoulders with no open gap.
    • Butted seam lines are permitted if required.
  • Shoulder straps are placed over the chest and back armor at the seams.
  • Armor is weathered with shades of grey.



TC animated back.jpg Back Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Rear center of back armor has detailed area that contains a O11 pattern.
  • Shoulder straps are placed over the chest and back armor at the seams.
  • Armor is weathered with shades of grey.



TC animated ab.jpg Abdomen Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Top edge of the armor is curved to match the chest.
  • Abdomen armor protrudes out in the middle to match the shape of the chest.
  • (4) inset lines divide the abdomen armor into segments.
  • Abdomen and kidney armor connect at the sides with no open gap.
    • A butted seam between abdomen and kidney armor is acceptable.
  • Armor is weathered with shades of grey.



TC animated grunt kidney.jpg Kidney Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Kidney and abdomen armor connect at the sides with no open gap.
    • A butted seam between the kidney and abdomen armor is acceptable.
  • Armor is weathered with shades of grey.



TC animated cod.jpg Codpiece and Belt front
For 501st approval:
  • Armor is painted matte or satin white.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • The front segments have a key/slot detail.
  • Belt boxes are mounted at the hips.
  • Cod and Posterior armor are connected at the hips.
    • Butted seams are permitted at this connection if required.
  • Armor is weathered with shades of grey.



TC animated butt.jpg Posterior Armor, belt rear and detonator
For 501st approval:
  • Armor is painted matte or satin white.
  • Belt is approx 3" tall and divided into 1.75" wide segments.
  • Codpiece and Posterior armor connect at the hips.
    • Butted seams are permitted at this connection if required.
  • Detonator is centered on the back of belt.
    • Detonator has no control buttons.
    • The detonator has 2 lines set in approx 1/2" - 5/8" from the edges.
      • Lines may be recessed or painted on
  • Armor is weathered with shades of grey.
For level two certification (if applicable):
  • Detonator lines are recessed.


TC animated belt box.jpg Belt Boxes
For 501st approval:
  • Two rectangular boxes are mounted at the hips.
  • Boxes are painted matte or satin white.
    • The top side of the box is tapered outward.
    • There is an inset detail near the top of each box.
  • Armor is weathered with shades of grey.



TC animated thighs.jpg Thigh Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Front of thigh armor has a flat triangular area near the knee with a notch cut out for the knee armor.
  • From the top of the triangle a ridge line travels up the front of the thigh to the top edge.
  • The upper outer edge has an angled section.
  • The armor is weathered with shades of grey.
For level two certification (if applicable):
  • Armor is seamless.
    • No visible traces of how the armor was assembled are shown.


600px-TC animated shins1 copy.jpg Lower Leg Armor
For 501st approval:
  • Armor is painted matte or satin white.
  • Knee armor is integrated with the lower leg.
  • The armor has a flat center triangle below the knee plate, with the single point facing downward.
  • The calf detail of the armor has a ridge wrapping around the back of the leg.
  • Due to the shape of the armor, a butted seam is permitted on the inside or back of the leg.
  • Armor is weathered with shades of grey.



TC animated boots.jpg Boots
For 501st approval:
  • White, ankle high or tall enough to cover the ankle and eliminate any black undersuit visible at the ankle area.
  • Boots are lace-less and have flat soles.
  • Boots have a center strip running from the toe to the ankle.
  • A strap across the top of the foot, and 2 flat white discs on either side of the foot, terminating the strap.
For level two certification (if applicable):
  • Boots have accurate notched sole.
Optional Accessories

Items below are optional costume accessories. These items are not required for approval, but if present must meet the guidelines below.


CRLdc15s-animated.jpg DC-15S Blaster Carbine (animated style)
For 501st approval:

Manufactured by BlasTech Industries, this weapon is commonly carried by the Troopers of the Galactic Republic.

  • This is the animated variant of the DC-15S blaster rifle.



Dc15a Animated.jpg DC-15A Blaster Rifle (animated style)
For 501st approval:

Manufactured by BlasTech Industries, this blaster is the standard issue weapon carried by the Clone Troopers of the Grand Army of the Republic.

  • This is the animated variant of the DC-15A blaster rifle.


This document and all of the images within were created by and are the property of the 501st Legion. All other uses are prohibited.

This CRL is available as a PDF at www.501st.com/databank/Costuming:BH_Cad_Bane_-_In_Denal_Disguise

The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. ©2012 Lucasfilm Ltd. & TM. All rights reserved. Used under authorization.

Visit www.501st.com to learn more.
Personal tools
The 501st Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While it is not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred Imperial costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © & ™ Lucasfilm Ltd. All rights reserved. Used under authorization.